D-Link AirPremier DWL-1700AP Bedienungsanleitung

This product can be set up usingThis product can be set up using

This product can be set up using

any current web browser, i.e.,any current web browser, i.e.,

any current web browser, i.e.,

Internet Explorer or NetscapeInternet Explorer or Netscape

Internet Explorer or Netscape

Navigator.Navigator.

Navigator.

DWL-1700APDWL-1700AP

DWL-1700AP

D-LinkD-Link

D-Link

AirAir

Air

PremierPremier

PremierTMTM

TMTM

Wireless Access PointWireless Access Point

Wireless Access Point

30M MIL-C-5015 Ethernet

Cable

specifications subject to change without notice. DWL-1700AP+. 03242003

Before You BeginBefore You Begin

Before You Begin

Check Your Package ContentsCheck Your Package Contents

Check Your Package Contents

DWL-1700AP Wireless Access Point

Inline Power Injector

Two rubber dipole antennas

It’s best to use a computer (with an Ethernet adapter) that is connected to a switch for

configuring the DWL-1700AP. The default IP address for the DWL-1700AP is

192.168.0.50:2000 with a Subnet Mask of 255.255.255.0 on the wired Ethernet side.

The default setting of the wireless side is 192.168.1.50, with the same subnet

mask.You will need to assign your computer a Static IP address within the same range

as the DWL-1700AP’s IP address for the purpose of configuring the DWL-1700AP. See

the Manual on the CD-ROM if you need assistance in assigning a Static IP address

for your network adapter.

If any of the above items are missing, please contact your reseller.

MIL-C-5015 RS232 Console Port Cable

Cross-over Ethernet cable

Grounding Wire

AC Power Cord

Mast and Wall Mounting kit

This product should ONLY be installed by experienced

installers who are familiar with local building and safety

codes and where ever applicable, are licensed by the

appropriate authorities. Failure to do so may void the D-Link product

warranty and may expose the end user or the service provider to legal and

financial liabilities. D-Link and its resellers or distributors are not liable for

injury, damage or violation of regulations associated with the installation of

outdoor units or antennas.

A safety grounding system is necessary to protect your outdoor

installation from lightning strikes and the build-up of static electricity. So

direct grounding of the antenna mast, Outdoor AP and Surge Arrester is

very important. And so mounting the Outdoor AP on the antenna mast,

you have to connect the Outdoor AP to the same grounding system with

the AC wall outlet.The grounding system must comply with the National

Electrical Code and safety standards that apply in your country. Always

check with a qualified electrician if you are in doubt as to whether your

outdoor installation is properly grounded.

Mounting your DWL-1700APMounting your DWL-1700AP

Mounting your DWL-1700AP

The DWL-1700AP can be mounted on the side of a building or mounted to a mast as shown in the

picture above. A wall (side) mount allows for mounting the DWL-1700AP on the side of a

building. This will provide a convenient mounting location when the roof overhang is not

excessive and/or the location is high enough to provide a clear line of sight.

A safe grounding system is necessary to protect your DWL-

1700AP from lightning strikes and the build-up of static

electricity when installed in an outside environment. So direct grounding

of the antenna mast, DWL-1700AP and Surge Arrester is very important. So

when mounting the DWL-1700AP on an antenna mast, you have to connect

the DWL-1700AP to the same grounding system with the AC wall outlet.

The grounding system must comply with the National Electrical Code and

safety standards that apply in your country. Always check with a qualified

electrician if you are in doubt as to whether your outdoor installation is

properly grounded.

A brief overview on mounting your DWL-1700AP

Step 1: With the unit powered off, attach the dipole antenna to the antenna

connector. NOTE: Do not over-tighten; tightness by hand is sufficient. Position the

antenna vertically for best omni-directional signal reception.

Step 2: Attach the Console Port cable to the Serial Port. Attach the other cable end

to the Serial Port on a PC running a terminal emulation program, and set the terminal

to 115200 Baud, No-Parity, 8 data bits, 1 Stop bit, and ANSI compatible. NOTE:

This connection is required only for setting up initial factory configuration information.

Step 3: Plug the female end of the power cord into the Inline Power Injector, and

then plug the male end of the power cord into a power outlet or power strip. The

Power LED on the front of the Inline Power Injector will light up.

Step 4: Run the cross over Ethernet cable (included in your package) from Data

Input Port (on the front of the Inline Power Injector) to the Ethernet Port on the PC we

mentioned

Step 5: Plug the MIL-C-5015 style Ethernet connector into the Special Ethernet port

on the back of the access point.

Step 6: Plug the RJ-45 Ethernet connector (the other end of the Special Ethernet

cable) into the Power & Data Output Port on the front of the Inline Power Injector.

When the Access Point receives power over the Ethernet cable, the Access Point

will start its boot sequence and the Active LED on the front of the Inline Power

Injector will light up.

Connecting The DWL-1700AP WirelessConnecting The DWL-1700AP Wireless

Connecting The DWL-1700AP Wireless

Access Point To Your NetworkAccess Point To Your Network

Access Point To Your Network

1. Special Ethernet port for connecting the MIL-C-5015 style Ethernet Cable

2. Special serial port for connecting the MIL-C-5015 style RS-232 console port cable

3. Power & Data output port for connecting the other of the MIL-C-5015 style Ethernet

4. Data input port for connecting the Ethernet Cable to a Hub Switch Router or a PC.

6. AC power input port for connecting the power cord.

Please refer to the product image on pg. 5

5. Special N-Type connector for connecting the antenna or RF cable.

Cable.

Hardware Installation Overview

Connecting The DWL-1700AP WirelessConnecting The DWL-1700AP Wireless

Connecting The DWL-1700AP Wireless

Access Point To Your NetworkAccess Point To Your Network

Access Point To Your Network

Using The Setup WizardUsing The Setup Wizard

Using The Setup Wizard

Open your Web browser

and type “http://

192.168.0.50:2000” into

the URL address box. Then

press the Enter or Return

key.

The logon pop-up

screen will appear.

Type “admin” for the

username and by

default the password

is “root”

Click OK

Once you have

logged in, the Home

screen will appear.

Click Run Wizard

****

Click Next

Step 1 - Set up your

new password. You

have the option to

establish a password.

Using The Setup Wizard (continued)Using The Setup Wizard (continued)

Using The Setup Wizard (continued)

You will see the

following screens.

Click Next

Step 2 - Internet

Connection Type (WAN)

Select your Internet

Connection type. Some

ISP’s provide you with an

automatic IP address, if

this is the case you

would select Dynamic. If

you are assigned an IP

address from your ISP,

select Static. In this QIG

we will be using Static.

Step 3 - Set Static IP

Address The DWL-

1700AP is capable of two

levels of wireless

encryption - 64-bit and

128-bit. By default

encryption is disabled.

You can change the

encryption settings for a

more secure wireless

network.

Using The Setup Wizard (continued)Using The Setup Wizard (continued)

Using The Setup Wizard (continued)

Step 4 - Set Wireless

LAN Connection

Enter your desired

ESS-ID and the

channel that you wish

to use here. This is

the ESS-ID that will be

broadcasted to

wireless users.

Click Next

Step 5 - Enable/

Disable Wireless

Encryption

If you wish to use

encryption, you may

enable here. If you

enable encryption,

please be sure to

select the encryption

level and also the

encryption key.

Using The Setup Wizard (continued)Using The Setup Wizard (continued)

Using The Setup Wizard (continued)

Click Next

When you have completed

the steps in this Quick

Installation Guide, your

connected network should

look similar to this:

Your Setup is Complete!Your Setup is Complete!

Your Setup is Complete!

Click Restart

Andere Handbücher für AirPremier DWL-1700AP

Inhaltsverzeichnis

Andere D-Link Drahtloser Zugangspunkt Handbücher

D-Link

D-Link DAP-1160 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

D-Link

D-Link Nuclias Connect DAP-2622 Bedienungsanleitung

D-Link

D-Link DWL-3500AP Bedienungsanleitung

D-Link

D-Link DAP-1160 Bedienungsanleitung

D-Link

D-Link DAP-2610 Bedienungsanleitung

D-Link

D-Link DWR-966 Bedienungsanleitung

D-Link

D-Link DWP-1010 Bedienungsanleitung

D-Link

D-Link DAP-3666 Bedienungsanleitung

D-Link

D-Link DWL-8220AP - AirPremier Wireless Switch Dualband Access... Bedienungsanleitung

D-Link

D-Link AirPlus DWL-900AP Bedienungsanleitung

D-Link

D-Link AirPremier N DAP-2360 Bedienungsanleitung

D-Link

D-Link xtreme n duo dap-1522 Kurzanleitung

D-Link

D-Link DWL-2700AP - AirPremier Outdoor Wireless Access... Bedienungsanleitung

D-Link

D-Link DAP-1620 Handbuch

D-Link

D-Link DAP-2590 - AirPremier N Dual Band PoE Access... Bedienungsanleitung

D-Link

D-Link AirPro DWL-5000AP Bedienungsanleitung

D-Link

D-Link DAP-2553 - Wireless N Dual Band Gigabit Access... Bedienungsanleitung

D-Link

D-Link DWL-X8630APE Bedienungsanleitung

D-Link

D-Link DAP-1360 Bedienungsanleitung

D-Link

D-Link DAP-2620 Bedienungsanleitung

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

D-Link

D-Link AirPremier N DAP-2360 Bedienungsanleitung

D-Link

D-Link DWL-1000AP Montageanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung