DAEWOO ELECTRONICS DV-F882DY-C Bedienungsanleitung
DAEWOO ELECTRONICS CO., LTD.
Service Manual
MODEL : DV-F882DY-C
DV-F882DY-A
DV-F882DY-C
DV-F882DY-A
DV-F882DY-M
DV-F882PY-D
DV-F802D-CP
DV-F802D-AP/
DV-F802P-DP
SPECIFICATIONS
SYSTEM
Video signal PAL standard colour
PAL/SECAM
channel memory 55 positions
UHF output signal 30-39 CH (adjustable)
73±3dBuV
VIDEO
Input: Video Line in 1.0Vp-p
75 ohms unbalanced, sync.
negative
Output: Video line out 75 ohms unbalanced, sync.
negative
Signal to noise ratio More than 43dB (SP)
Horizontal resolution 230 lines
AUDIO
Input: Audio Line in Impedance: more than
50Kohm
–8 dBm, unbalanced
Output: Audio line out Impedance: less than 1Kohm
–6 dBm, unbalanced
Frequency response 100 Hz-8KHz
Hi-Fi, 20Hz-20kHz
Signal to noise ratio More than 38 dB
Hi-Fi More than 60dB
Audio Distortion Less than 3% (SP)
Hi-Fi Less than 0.5%
TAPE TRANSPORT
Tape width 12.65mm (1/2")
Tape speed 23.39mm/sec
Maximum recording time 360 min, with E-180 tape (LP)
FF. REW time Approx 4 min (E-180)
GENERAL
Power requirements AC 230V 50Hz
Power consumption 19W
Nicam 20W
DIMENSIONS
Set size (WxHxD) 360x90x312 mm
Carton size (WxHxD) 445x180x412 mm
Weight (gross) 5.4Kg
Channel coverage
SYSTEM PAL,SECAM-B/G
PAL,SECAM-B/G,D/K PAL-I
HYPER BAND
VHF Ch 2~12
UHF Ch 21~69
Channel CATV Ch X,Y,Z UHF Ch 21~69
SI~S41
IN/OUTPUT JACK TYPE
Model EUROPE
JACK SCART Type
TYPE
• Safety Check after Servicing
Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires
have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order
to verify compliance with safety standards.
1. Insulation resistance test
Confirm the specified insulation resistance or greater between power cord plug prongs and externally exposed parts of
the set (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone
jacks, etc.). See table below.
2. Dielectric strength test
Confirm specified dielectric strength or greater between power cord plug prongs and exposed accessible parts of the
set (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks,
etc.) See table below.
3. Clearance distance
When replacing primary circuit components, confirm
specified clearance distance (d), (d') between soldered
terminals, and between terminals and surrounding
metalic parts. See table below.
Table 1: Rating for selected areas
* Class II model only.
Note: This table is unofficial and for reference only. Be sure to confirm the precise values for your particular country and
locality.
4. Leakage current test
Confirm specified or lower leakage current between B (earth ground, power cord plug prongs) and externally exposed
accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks,
earphone jacks, etc.)
Measuring Method: (Power ON)
Insert load Z between B (earth ground, power cord plug
prongs) and exposed accesible parts. Use and AC
voltmeter to measure across both terminals of load Z.
See figure 2 and following table.
Table 2: Leakage current ratings for selected areas
Note: This table is unofficial and for reference only. Be sure to confirm the precise values for your particular country and
locality.
Fig. 2
AC Line Voltage Region Insulation Dielectric Clearance
Resistance Strength Distance (d), (d')
100V Japan ≥1 MΩ/500 V DC 1kV AC 1 minute ≥3 mm
110 to 130V USA & – – – 900V AC 1 minute ≥3.2mm
Canada
* 110 to 130 V Europe ≥4 MΩ/500 V DC 3 kV AC 1 minute ≥6 mm (d)
200 to 240 V Australia ≥8 mm (d')
(a: Power cord)
AC Line Voltage Region Earth Ground
Load Z Leakage Current (i) (B) to:
100V Japan ¡ ≤1m A rms Exposed accessible
parts
110 to 130 V USA & ¡ ≤0.5 m A rms Exposed accessible
parts
¡ ≤0.7 m A peak Antenna earth
110 to 130 V Europe ¡ ≤2 m A dc terminals
200 to 240 V Australia ¡ ≤0.7 m A peak Other terminals
¡ ≤2 m A dc
Fig. 1
1k
1.5k
1.5kµF
2k
50k
d
Primary circuit termimals
Chassis
d'
a
Z
Exposed
accessible
part AC Voltmter
(high impedance)
Earth Ground
power cord plug prongsB
TABLE OF CONTENTS
SECTION 1. CONTROLS AND FUNCTIONS..........................................................................................................2
SECTION 2. ELECTRICAL ADJUSTMENTS
2-1. SERVO CIRCUIT ADJUSTMENT METHOD.....................................................................................................................3
2-2. AUDIO CIRCUIT ADJUSTMENT METHOD......................................................................................................................4
2-3. IF MODULE CIRCUIT ADJUSTMENT METHOD..............................................................................................................5
SECTION 3. TROUBLE SHOOTING FLOW CHART
3-1. POWER CIRCUIT.............................................................................................................................................................16
3-2. LOGIC CIRCUIT...............................................................................................................................................................18
3-3. SERVO-SYSCON CIRCUIT.............................................................................................................................................20
3-4. AUDIO CIRCUIRT (NORMAL) .........................................................................................................................................25
3-5. AUDIO CIRCUIT (HI-FI)....................................................................................................................................................27
3-6. VIDEO CIRCUIT ...............................................................................................................................................................29
SECTION 4. CIRCUIT DIAGRAM
4-1. CONNECTION DIAGRAM (DV-F802 SERIES)................................................................................................................39
4-2. CONNECTION DIAGRAM (DV-F882 SERIES)................................................................................................................40
4-3. POWER CIRCUIT.............................................................................................................................................................41
4-4. SERVO-LOGIC CIRCUIT.................................................................................................................................................42
4-5. LOGIC CIRCUIT (DV-F802 SERIES)...............................................................................................................................43
4-6. LOGIC CIRCUIT II (DV-F882 SERIES) ............................................................................................................................44
4-7. HEADAMP CIRCUIT........................................................................................................................................................45
4-8. VIDEO CIRCUIT ...............................................................................................................................................................46
4-9. HI-FI AUDIO CIRCUIT......................................................................................................................................................47
4-10. PIF NICAM CIRCUIT......................................................................................................................................................48
4-11. PIF/MPX CIRCUIT..........................................................................................................................................................49
4-12. PIF CIRCUIT...................................................................................................................................................................50
4-13. OSD CIRCUIT ................................................................................................................................................................51
4-14. VPS/PDC CIRCUIT........................................................................................................................................................52
4-15. IN/OUT SW CIRCUIT I...................................................................................................................................................53
4-16. IN/OUT SW CIRCUIT II..................................................................................................................................................54
4-17.REMOCON CIRCUIT......................................................................................................................................................55
SECTION 5. VOLTAGE CHARTS.................................................................................................................................56
SECTION 6. COMPONENTS LOCATION GUIDE ON PCB BOTTOM VIEW........................................64
SECTION 7. DIS ASSEMBLY ........................................................................................................................................69
SECTION 8. ELECTRICAL PARTS LIST..................................................................................................................73
1
SECTION 1. CONTROLS AND FUNCTIONS
2
PLAY
STOP
POWER
EJECT
REC/OTR
REW FF
=
POWER
EJECT
REC/OTR
REW FF
PLAY
STOP
VIDEO L –AUDIO– R
CHANNEL
B.L.U.E D.I.A.M.O.N.D
RAPID REWIND SYSTEM
=
REC/OTR
POWER EJECT
õ CH.TRK.ö
PLAY
REW F.F
STOP
DV-F882 Series
DV-F802 Series
RF OUT
ANT. IN
TV
EURO-AV
OFF
CH.H CH.L
TEST
ON
FRONT
REAR
2-1. SERVO CIRCUIT ADJUSTMENT METHOD
1. PLAYBACK PHASE
• Connection Method
• Adjustment Procedure
1) Play back the test tape.(DP-2)
2) Set the oscilloscope to the CHOP mode. Connect CH1 to the SW PULSE (PT01 PIN ¤Ø).
3) Insert PATH JIG and Press “REC” button on the remote controller.
4) Check the position of the V-sync from the rising edge of the SW pulse.
(Standard: 6.5H±0.5H)
SECTION 2. ELECTRICAL ADJUSTMENT
Adjustment Parts Checking Point Measuring Equipment Mode Test Tape
JPT01 DP-2
Check PT01 PIN ¤Ø Oscilloscope Play
Modulator
JPT01
CH-1
OSCILLOSCOPE
CH-2
PT01 TOP VIEW
PATH JIG 6
3
2-2. AUDIO CIRCUIT ADJUSTMENT METHOD
1. AUDIO RECORD BIAS
• Connection Method
• Adjustment Procedure
1) Set the TV/LINE to LINE mode.
2) Set the input to open mode
3) Connect the Audio level meter to both TP1 and TP2
4) After inserting a blank tape, record in SP mode.
5) Adjust R290 to obtain 3.0 mVrms.
4
TOP VIEW
R290
3.0mVrms +
–
A/CHEAD
TP2
(–)
TP1
(+)
Audio LEVEL METER
S/N: 97P65064HA
HEAD AMP PCB
Adjustment Parts Checking Point Measuring Equipment Test Tape Input Signal
R290 A/C Head PCB Audio level meter Rec None signal
TP1(+), TP2(-)
5
2-3. IF MODULE CIRCUIT ADJUSTMENT METHOD
2-3-1. PAL B/G 2 CARRIER SYSTEM
1. 32.4MHz TRAP
• Connection Method
• Adjustment Procedure
1) Supply +12V to pin No.1, and GND to Pin No 2. of 102
2) Connect the signal generator output to pin 3 and GND to pin 2 of P102.
3) Connect the oscilloscope to TP1.
4) Adjust L101 until the level of signal becomes minimum.
P102
L104
L105
IC101
#3
#2
L101 TP1 L108
TP2
L103 Z101
TP6 TP7
IC102
TP3
L109
P101
IC103
L110
TP4
minimum
CH-1
Oscilloscope
GND
OUT
#3
PIF PCB (Component Side)
SIGNAL
GENERATOR
fc: 32.4 MHz (No modulation)
Output Level: 80dBµV (75Ω loaded)
#2
Adjustment Parts Checking Point Measuring Equipment Condition of Adj. Input Signal
L101 TP1 Oscilloscope EE Mode Refer to the
Signal Gen followings
2. PIF COIL
• Connection Method
• Adjustment Procedure
1) Supply +12V to pin No.1, and GND to Pin No 2. of 102
2) Connect the signal generator output to pin 3 and GND to pin 2 of P102.
3) Connect the oscilloscope to TP2.
4) Adjust L104 to obtain the minimum DC voltage of TP2.
6
P102
L104
L105
IC101
#3
#2
L101 TP1 L108
TP2
L103 Z101
TP6 TP7
IC102
TP3
L109
P101
IC103
L110
TP4
CH-1
Oscilloscope
GND
OUT
minimum
#3
PIF PCB (Component Side)
SIGNAL
GENERATOR
fc: 38.9MHz
Output Level: 80dBµV (75Ω loaded)
#2
Adjustment Parts Checking Point Measuring Equipment Condition of Adj. Input Signal
L104 TP2 Oscilloscope EE Mode Refer to the
Signal Gen followings
3. AFT COIL
• Connection Method
• Adjustment Procedure
1) Supply +12V to pin No.1, and GND to Pin No 2. of 102
2) Connect the signal generator output to pin 3 and GND to pin 2 of P102.
3) Connect the Test circuit to pin No. 7 of P102
4) Connect the oscilloscope to “A” point and GND
5) Adjust L105 to obtain 2.3V DC Voltage at the "A" point
7
P102
L104
L105
IC101
#3
#2
L101 TP1 L108
TP2
L103 Z101
TP6 TP7
IC102
TP3
L109
P101
IC103
L110
TP4
2.3±0.5V
CH-1
Oscilloscope
GND OUT
#3
#7
PIF PCB (Component Side)
#2
#7
SIGNAL
GENERATOR
fc: 38.9MHz, fm: 15.625KHz (30% AM Modulation)
Output level: 80dBµV (75Ω loaded)
43kΩ
33kΩ
18kΩ
"A"
Vcc+12V
GND
(Test circuit)
Adjustment Parts Checking Point Measuring Equipment Condition of Adj. Input Signal
L105 “A” point Oscilloscope EE Mode Refer to the
Signal Gen. followings
Dieses Handbuch passt für folgende Modelle
6
Inhaltsverzeichnis
Andere DAEWOO ELECTRONICS DVR Handbücher
