DAVIS Vantage Pro2 Updater Bedienungsanleitung

Vantage Pro2™Temperature/Humidity Sensor

Replacement Kit

The following instructions are for replacing the Temperature/Humidity sensor

on Vantage Pro2™stations (# 6152, 6152C, 6162, 6162C, 6382) manufactured

after January 2006.

Components

The replacement kit includes the following components:

Tools Needed

You may need some or all of the following tools and other items to install the

Temperature/Humidity Sensor Replacement Kit:

• A medium Phillips-Head screwdriver

• Other tools as required to remove and re-mount the Integrated Sensor Suite

(ISS) or Temperature/Humidity Station.

• Optional — Adjustable crescent wrench

Installing the Temperature/Humidity Sensor

Replacement Kit

The Temperature/Humidity Sensor Replacement Kit works with both the ISS

and Temperature/Humidity stations.

The ISS assembly for Vantage Pro2 stations (# 6152,

6152C, 6162 and 6162C) contains the rain cone,

Sensor Interface Module (SIM) housing, and the

radiation shield plating which houses the

Temperature/Humidity sensor. The ISS is also

available with extra optional components like the

UV and Solar Radiation sensors and mounting

bracket if you have purchased a Vantage Pro2 Plus

(# 6162, 6162C) unit or have purchased these items

separately.

Insulated disk with mounted

Temperature/Humidity senso

#6 screws (2)

ISS

The Temperature/Humidity Station (# 6382)

contains a Temperature/Humidity sensor in a

radiation shield and connects to a provided SIM

shelter.

Optional — Put Console in Setup Mode

If you have a console, you need to put it in Setup Mode. This prevents the

reception of erroneous data while you are removing the ISS. To put your

console in Setup Mode:

• At your Vantage Pro2 console, press and hold DONE and then press the

down arrow ( - ) to put the console in Setup Mode. The “Receiving from...”

screen will display.

Note: Additional information on clearing and setting console data can be found in the

Vantage Pro2 Console Manual.

If you have an Envoy and are concerned with erroneous data, you may edit the

data via the WeatherLink software. See the WeatherLink Online Help for more

information.

Take Down the ISS

Please work on your Vantage Pro2 ISS in a safe place. We strongly

recommend that you take the station down from its sited location before

replacing the sensor.

To take down the ISS:

1. Locate the SIM housing cover on the side of the ISS and open it.

2. Disconnect the Solar Panel wire on the SIM cover from the SIM board by

pulling the Solar Panel connector.

3. Pull the foam insert out of the cable access port in between the cables and

set the foam insert aside.

4. Disconnect the anemometer cable from the sensor connector labeled

WIND and slide the cable out of the cable access port.

5. Cabled ISS Only: Disconnect the console cable from the SIM.

6. You can now remove the ISS from its mounted position. Move it to a safe

place to install the sensor.

Temperature/Humidity Station

Disassemble the Standard Radiation Shield — ISS

Note: We recommend using a workbench or table to perform the following procedures.

1. Open and remove the SIM cover if you have not done so already.

2. Disconnect the TEMP/HUM cable from the SIM

and slide the cable out of the cable access port.

3. Remove the rain collector cone from the ISS base

by rotating the cone counter-clockwise. When the

cone’s latches line up with openings in the base,

you can lift the cone off. The cone fits in the base

tightly and may require extra pressure to remove.

Steady the ISS base between your knees when

removing the cone.

4. Remove the three 8-32 x 4''

screws holding the radiation

shield plates together from the

top of the rain collector base.

5. Separate out the radiation

shielding plates to locate the

Temperature/Humidity sensor

in the plating. See “Remove the

Previous Temperature/

Humidity Sensor” on page 4 for

instructions on removing the

previous sensor.

Twist to Open

4" Screw

Plates

Rain Collector Base

Temp/Humidity

Sensor

Lock

Washer

Flat

Washer

Disassemble the Radiation Shield — Temperature/Humidity

Station

Note: We recommend using a workbench or table to perform the following procedures.

1. Place the Temperature/

Humidity Station on a

level surface.

2. Loosen the three

mounting screws that

hold the mounting

bracket and the

radiation shield

together.

3. Separate the radiation

shield plates to locate

the Temperature/

Humidity sensor in the

plating. See “Remove

the Previous

Temperature/Humidity

Sensor” below for

instructions on

removing the previous sensor.

Remove the Previous Temperature/Humidity Sensor

1. Locate the Temperature/Humidity sensor on the second to bottom plate in

the radiation shield plating stack.

2. Remove the three screws and flat washer securing the Temperature/

Humidity sensor to the radiation plating.

Mounting

Bracket

Radiation

Shield

Assembly

Lock Washers

Flat Washers

4" Screws

Cable Clamp

emperature/Humidity

Sensor

Note: The orientation of the Temperature/Humidity sensor may be different from station to

station. Even if the sensor is inverted and attached to spacers it should still be removed

and replaced with the Temperature/Humidity sensor replacement kit.

3. Remove the sensor and cable clamp from the plate.

4. Return the plate to the radiation plating stack in the order it was mounted.

Insert the Temperature/Humidity Sensor

1. Locate the plate at the top of the radiation shield plating and find the

insulating disk on the underside of the plate.

2. Remove the two screws holding the insulating disk attached on the

underside and discard the disk.

3. Take the insulating disk with the mounted Temperature/Humidity sensor

and set it in the same place as the previous insulating disk.

Top Plate

Insulating Disk

4. Use the screws that were taken from the last insulating disk or use the

screws provided with the Temperature/Humidity Sensor Replacement Kit

to mount the Temperature/Humidity sensor in place.

5. Reassemble the radiation

shield plating.

6. Check the orientation of

the Temperature/

Humidity sensor cable.

When the plating is

reassembled, the cable

should be oriented on the

right side of the plating

so that it can be easily

placed between the top

radiation shield and the

rain collector base.

7. Replace the three 4''

screws, lock washers and

flat washers into their

respective holes in the

rain collector base and

screw the radiation shield

plates back into place.

Re-install the ISS

1. Install the rain collector

cone and lock it in place.

2. Slide the new

Temperature/Humidity

sensor cable back

through the cable access

port of the SIM box.

3. Connect the Temperature/Humidity sensor cable into the correct port.

4. Close the SIM cover temporarily without connecting the solar panel

cables.

5. Test communication between the ISS and the console. To test

communication, take the console out of Setup Mode (see “Take the

Console Out of Setup Mode” on page 7 for more information) and make

sure the console is receiving data from the ISS or Temperature/Humidity

Station. See the ISS manual or Temperature/Humidity Station Manual for

more information on testing communication.

4" Screw

(3)

Plates

Rain Collector Base

Temp/Humidity

Sensor Plate

Lock

Washer

Flat

Washer

6. Re-install the ISS in its previous location.

7. Open the SIM cover and connect the WIND (anemometer) cable.

8. Plug in the solar panel cable to the solar panel connector.

9. Cabled ISS Only: Connect the console cable.

10. Re-insert the foam into the cable access port in the SIM box.

11. Close the SIM box.

12. Use cable ties to secure cables.

Take the Console Out of Setup Mode

1. At your Vantage Pro2 console, press and hold DONE for three seconds to

take the console out of Setup Mode.

2. Check the console for erroneous rain data and clear if necessary.

To clear erroneous daily rain data:

• Select the RAINDAY button. The graph icon displays next to the daily

rain variable.

• Press and release 2ND, then immediately press and hold CLEAR.

• The daily rain variable will start blinking.

• Keep holding CLEAR until the reading changes to zero.

• Refer to your Vantage Pro2 Console Manual for more information on

clearing any other weather variables or clearing all weather variables in

the console.

You have completed the replacement kit.

This product complies with the essential protection requirements

of the EC EMC Directive 89/336/EC.

Vantage Pro2 Temperature Humidity Sensor Replacement Kit

Rev. A, February 1, 2008

Document Part Number: 07395.243

Used with Temperature/Humidity Sensor Replacement Kit # 6930

For Vantage Pro2 Stations # 6152, 6152C, 6162, 6162C, 6382

Vantage Pro®and Vantage Pro2™are trademarks of Davis Instruments Corp., Hayward, CA.

Information in this document subject to change without notice.

Tested to comply

with FCC standards

FOR HOME OR OFFICE USE

3465 Diablo Avenue, Hayward, CA 94545-2778 U.S.A.

510-732-9229 • Fax: 510-732-9188

E-mail: [email protected] • www.davisnet.com

Contacting Davis Technical Support

If you have any questions, or encounter problems with your Vantage Pro2

weather station, or with the current firmware installation, please contact Davis

Technical Support. We’ll be glad to help.

(510) 732-7814 — Monday - Friday, 7:00 a.m. - 5:30 p.m. Pacific Time. We

are unable to accept collect calls.

(510) 670-0589 — Technical Support Fax.

[email protected] — E-mail to Technical Support.

[email protected] — General e-mail.

www.davisnet.com — Davis Instruments web site. See the Weather Support

section for copies of user manuals, product specifications, application notes,

and information on software updates. Watch for FAQs and other updates.

Andere Handbücher für Vantage Pro2 Updater

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere DAVIS Zubehör Handbücher

DAVIS

DAVIS Wireless Temperature/Humidity Station Bedienungsanleitung

DAVIS

DAVIS 7714 Radiation Shield Bedienungsanleitung

DAVIS

DAVIS Solar Power Kit Bedienungsanleitung

DAVIS

DAVIS Wireless Temperature/Humidity Station Bedienungsanleitung

DAVIS

DAVIS Vantage Pro2 Updater Bedienungsanleitung

DAVIS

DAVIS 6440 Bedienungsanleitung

DAVIS

DAVIS ISS Leitfaden

DAVIS

DAVIS Surge Protector Shelter (Small) Bedienungsanleitung

DAVIS

DAVIS 6322C Bedienungsanleitung

DAVIS

DAVIS 6151 Bedienungsanleitung

DAVIS

DAVIS Soil Moisture Sensor & Temperature Probe Bedienungsanleitung

DAVIS

DAVIS Vantage Pro2 Updater Bedienungsanleitung

DAVIS

DAVIS UV Sensor Bedienungsanleitung

DAVIS

DAVIS Solar Power Kit Bedienungsanleitung

DAVIS

DAVIS Solar Radiation Sensor Bedienungsanleitung

DAVIS

DAVIS Vantage Pro ISS Retrofit Kit Bedienungsanleitung

DAVIS

DAVIS AirLink Bedienungsanleitung

DAVIS

DAVIS Solar Power Kit Bedienungsanleitung

DAVIS

DAVIS 6440 Bedienungsanleitung

DAVIS

DAVIS Vantage Pro ISS Retrofit Kit Bedienungsanleitung

DAVIS

DAVIS Vantage Pro2 Updater Bedienungsanleitung

DAVIS

DAVIS 7817 Bedienungsanleitung

DAVIS

DAVIS and Vantage Pro Bedienungsanleitung

DAVIS

DAVIS 7709 Solar Power kit Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung