DAVIS And Vantage Pro Bedienungsanleitung

Product # 6311

VANTAGE PRO®UPDATER

User’s Guide

Vantage Pro Updater Overview

The Vantage Pro Updater allows you to update the firmware in a Vantage con-

sole via the expansion port used by the WeatherLink data logger. The Updater

can be powered by a 5 Volt Vantage Pro AC-power adapter or a 9V battery. One

9V battery should provide over 20 hours of operation.

Section 1: Using the VP Updater

Updating the Vantage Pro Console Firmware

These are the basic steps involved in using the Updater to reprogram the firm-

ware in a Vantage Pro console.

1. If you are using WeatherLink software with your Vantage Pro weather sta-

tion, be sure to download the weather data into your computer before

beginning this procedure.

2. Press the [DONE] key and the down arrow [-] key on your VP console to

enter setup mode. This will preserve the time and other settings on your

console.

3. Remove power from the console by unplugging the AC wall adapter and

removing the batteries.

4. If a WeatherLink data logger is installed, remove it from the console.

5. Turn the VP Updater on. The Status LED should be GREEN. If it shows

another color, see the Status LED Summary Table.

6. Insert the Link Program Adapter (See Figure 2) into the console expansion

port. See Figure 1 for location of port. It’s the same port used by the Weath-

erLink data logger.

7. Press the Updater Start Button. The LED should start flashing YELLOW.

8. When Updater is done programming, the LED will turn GREEN and you

will hear 1 beep. A RED or YELLOW LED indicates a problem. See the Sta-

tus LED Summary Table and the Troubleshooting Notes for more informa-

tion.

9. Unplug the Updater from the Console.

10. If you have a WeatherLink data logger, plug it into the console.

11. Restart the console by replacing the batteries and/or connecting the AC

wall adapter.

12. Check the release notes for the version of firmware you just installed. You

may have additional steps to perform in order to complete the update.

Page 2 Vantage Pro® Updater

Status LED Summary Table

Troubleshooting Notes

On power up the Updater will beep twice and sequence the colors of the LED.

When the LED is GREEN it is ready to use. The first beep indicates the processor

is running. The second beep means it can talk to the flash memory where the

firmware image to be loaded is stored.

• If you do not hear a beep after powering up, the battery is dead or some-

thing is wrong with the Updater.

• If you do hear a beep after powering up, but the LED is left off showing no

color, the Updater has detected a low battery condition.

• If, after pressing the Start button the LED does not change to flashing YEL-

LOW but instead beeps twice and goes to RED, the Updater cannot talk to

the console. Check connections and press Start again.

• If firmware has been updated correctly, the status LED turns GREEN.

• If a target flash page does not verify, the status LED will turn solid RED.

• If the fuse bits do not program correctly, the status LED will be solid YEL-

LOW.

• If the console did not program correctly, you can push the Start button to

try to program it again.

• If the firmware fails the verification, the status LED will start flashing RED.

You can push the Start button to leave this state and go to the GREEN state.

Note: The Vantage Pro Updater sends diagnostic messages through its serial port that may be

helpful if the operator is puzzled about what is going on. These messages can be viewed in

PROCOMM or HYPERTERMINAL.

LED Color Updater Status Additional Info

Solid Green The Updater is ready. If after programming, it means

everything programmed ok.

Solid Yellow The fuse bits did not program cor-

rectly.

Solid Red The target flash did not program

correctly. If just after the Start button is

pushed,theUpdaterisnottalking

to the target at all.

No Color The battery is low.

Flashing Yellow Target flash pages for firmware

are being programmed or veri-

fied.

Flashing Red The firmware update failed verifi-

cation. If the condition repeats, the Up-

dater flash memory may be cor-

rupt. Reload the firmware into the

VP Updater.

Page 3

Vantage Pro Console

Data Logger Battery Cove

Expansion Port

Figure 1. Data Logger and Console

ON/OFF

Switch

#6311

Vantage Pro®Updater

START

Status

Light

Start

Button

Link

Program

Adapter

Serial

Port

igure 2. Vantage Pro Updater

Product Numbers: 6311

Davis Instruments Part Number: 7395.310

Vantage Pro Updater User’s Guide

Rev A Manual (4/24/2002)

3465 Diablo Avenue, Hayward, CA 94545-2778 U.S.A.

510-732-9229 • Fax: 510-732-9188

E-mail: [email protected] • www.davisnet.com

Section 2: Advanced Operations

Updating the Updater Overview

The Updater software (updater.exe) allows you to load new versions of firm-

ware into the VP Updater. The firmware image is stored in a file named flash.bin

and can be downloaded from the Support section of our website: www.davis-

net.com.

A PC is required to install new versions of firmware on the VP Updater. The

installation is done through a serial port at 19,200 using the Updater software

provided by Davis.

Using Updater Software to Update the Updater

1. Make sure the flash.bin file is in the Updater software directory before you

start the program.

2. Connect the included serial cable to the Updater’s serial port (see Fig. 2).

The other end of the cable connects to the serial port on your computer

using the included serial port adapter.

3. Turn the VP Updater ON using the ON switch (see Figure 2).

4. Start the Updater software.

5. The software should detect the VP Updater on one of your serial ports.

Note: If the Updater Software doesn’t detect the VP Updater, check all the connections and

make sure battery is good or check that the AC-power adapter is connected and receiv-

ing power.

6. When the software asks, "LOAD NEW FIRMWARE TO UPDATER? (Y or N)":

• Press “Y” to update the firmware in the Updater.

• You can press “N” to cancel the operation.

7. The program will load the new firmware into the VP Updater and double

check that the firmware loaded correctly.

8. Type 'Q' to quite the program. You can then close the window.

Contacting Davis Instruments

(510) 732-7814 Technical Support, Monday – Friday, 7:00 a.m. – 5:30 p.m. Pacific Time.

(510) 670-0589 Fax to Customer Service or Tech Support.

www.davisnet.com Davis Instruments’ website. Check out the Weather Support section.

support@davisnet.com E-mail to Technical Support.

Andere Handbücher für and Vantage Pro

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere DAVIS Zubehör Handbücher

DAVIS

DAVIS 6322C Bedienungsanleitung

DAVIS

DAVIS Short-Range Modem Pair Bedienungsanleitung

DAVIS

DAVIS Surge Protector Shelter (Small) Bedienungsanleitung

DAVIS

DAVIS Solar Power Kit Bedienungsanleitung

DAVIS

DAVIS Vantage Pro ISS Retrofit Kit Bedienungsanleitung

DAVIS

DAVIS Wireless Temperature/Humidity Station Bedienungsanleitung

DAVIS

DAVIS Soil Moisture Sensor & Temperature Probe Bedienungsanleitung

DAVIS

DAVIS 6151 Bedienungsanleitung

DAVIS

DAVIS Solar Radiation Sensor Bedienungsanleitung

DAVIS

DAVIS Vantage Pro2 Updater Bedienungsanleitung

DAVIS

DAVIS WeatherLink Live 6100 Bedienungsanleitung

DAVIS

DAVIS 7714 Radiation Shield Bedienungsanleitung

DAVIS

DAVIS 7709 Solar Power kit Bedienungsanleitung

DAVIS

DAVIS Vantage Vue ISS Bedienungsanleitung

DAVIS

DAVIS Vantage Pro2 Updater Bedienungsanleitung

DAVIS

DAVIS UV Sensor Bedienungsanleitung

DAVIS

DAVIS Vantage Pro2 Updater Bedienungsanleitung

DAVIS

DAVIS Vantage Pro2 Updater Bedienungsanleitung

DAVIS

DAVIS ISS Leitfaden

DAVIS

DAVIS 7817 Bedienungsanleitung

DAVIS

DAVIS SONIC-ANEMO-DZP Bedienungsanleitung

DAVIS

DAVIS Wireless Temperature/Humidity Station Bedienungsanleitung

DAVIS

DAVIS 6151 Bedienungsanleitung

DAVIS

DAVIS AirLink Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

DAVIS and Vantage Pro Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken