De Agostini Model Space C57 Bedienungsanleitung
Build the
Steam
Locomotive
Pack 03
Contents
Stage 13: The safety valves and motion bars
Stage 14: The piston rods and cylinder covers
Stage 15: The cylinder side plates
Stage 16: The piston rods and crossheads
Stage 17: The rear underframe
Stage 18: Rear end beam and plate
Stage 19: The motion frame
Stage 20: The equalising bars
31
33
35
38
40
42
44
46
Step by step Pages
Editorial and design by Continuo Creative, 39-41 North Road, London N7 9DP.
Published in the UK by De Agostini UK Ltd, Battersea Studios 2, 82 Silverthorne Road, London SW8 3HE.
Published in the USA by De Agostini Publishing USA, Inc., 915 Broadway, Suite 609, New York, NY 10010.
All rights reserved © 2016
Warning: Not suitable for children under the age of 14. is product is not a toy and is not designed or intended for use in play. Items may vary
from those shown.
Build the
Steam
Locomotive
Step by step: Stage
Tools
Where your parts t
31
13
The safety valves and
motion bars
Front steam chest covers × 2
Piston valve tail guides A × 2
Piston valve tail guides B × 2
Motion bars × 2
Cylinder safety valves × 2
2 × 5mm screws x 3
Phillips screwdriver
Synthetic rubber adhesive
Flat le or sandpaper
Toothpick
1
Valve guideCylinder safety valve Motion bar
Your parts
Insert one of the cylinder safety valves into one of the cylinder covers on the rear plate,
into the hole from which the screw was removed in Stage 12.
Insert the second safety
valve into the hole in the
cover on the other side of
the rear plate.
32
2 3
4 5 Complete
Check the two motion bars
for any burrs or ash left
over from casting.
Position the front
end of one of
the bars over the
hole in the square
projection on
the cover.
Repeat this for the other cover.
Apply a small amount of synthetic rubber
adhesive to the front steam chest covers,
and insert the covers into the two holes in
the front plate, pressing rmly into place.
Loosely x it in
place with a 2 ×
5mm screw.
Remove any you nd with a
le or sandpaper, taking care
not to alter the bars’ shape.
Apply synthetic
rubber adhesive to
the front of piston
valve tail guides B,
and combine with
guides A, as shown.
Remove any excess
adhesive with a
toothpick.
Apply synthetic rubber adhesive to
the front sides of the piston valve
tail guides A. Insert the guides into
the holes on the rear cylinder plate,
above the covers. Before the glue
dries, adjust the position of the
guides so they are vertical (red line)
and parallel to the underframe.
Round hole - front end Oval hole - rear
Top
Bottom
Step by step: Stage
Tools
Where your parts t
33
14
The piston rods and
cylinder covers
Piston rods × 2
Piston rod housings × 2
Cylinder safety valves × 2
Front cylinder covers × 2 Synthetic rubber adhesive
Instant adhesive
1
Front cylinder cover Piston assembly rod guide
Piston assembly rod guide
Apply synthetic rubber adhesive to
the thin end of one of the piston rods.
Insert the piston rod into the hole in the
rectangular end of a piston rod housing.
Remove any excess adhesive
from around the join between
the two parts.
Your parts
34
23
4
Complete
It is always best to use as
small an amount of instant
adhesive as possible, but,
as it is a liquid adhesive, it
is easy to apply too much.
If this happens, you can
use some tissue twisted
to a point to soak up the
excess, as shown on the
right. You can also use a
cotton swab, but this will
lack the narrow tip that
the rolled tissue will have.
As superglue dries quickly,
you will need to act fast.
Before the adhesive
dries, place the assembly
on a at surface. Check
that the rod is vertical
from all directions.
Apply synthetic rubber
adhesive to the back
side of one of
the front cylinder
covers, avoiding the
circled hole.
Screw one of the safety valves
into the hole at the bottom of the
cylinder cover.
Hold the rod in position
and apply some instant
adhesive to the inside of
the housing.
Align the position of the
small hole with the one
in the cylinder plate.
Insert the centre of the
cover into the large hole
in the plate.
Repeat the process to t the other
cylinder cover and safety valve.
Allow the adhesive to
dry, then repeat this
process to assemble
the second set. Before the adhesive
dries look through the
small hole to ensure it
is aligned.
Apply some synthetic rubber
adhesive to the back of both
piston rod housings.
Place the housings onto the
projections in the centres of the
front cylinder covers (circled).
Front
Back
Tip
Step by step: Stage
Tools
Where your parts t
35
15
1
The cylinder
side plates
Air valve wheels × 2
Inspection hatches × 2
Hole covers × 4
2 × 2mm screws × 30
Cylinder side plates × 2
Drainage pipes × 2
Phillips screwdriver
Synthetic rubber adhesive
Instant adhesive
Soft cloth or towel
Cylinder side plate
Your parts
On the front side of each inspection
hatch, the projections at the top and
bottom (outlined) are raised.
Apply synthetic rubber adhesive
to the back of one of the
inspection hatches and glue it
into place on the side plate.
Drainage pipe
Back
Front
Place a cylinder side plate, an air valve wheel,
an inspection hatch and two hole covers as
shown above.
Ax here
36
2
4
3
5
Prepare one of the
air valve wheels and
two hole covers.
Position the wheel
with the projections
at the arrowed
points when gluing
to the side plate.
Apply synthetic
rubber adhesive
to the back of the
wheel and glue
it into the circled
hole. Adjust the position of the wheel
so that the projections match
those shown above left.
Apply synthetic rubber
adhesive to the pins on the
backs of the hole covers and
place them into the circled
holes in the side plate.
Don’t let any
glue block
the holes
at the side of
the plate.
Align the side plate
assembly with the
left front and rear
cylinder plates.
Half-tighten a 2 ×
2mm screw into each
of the aligned holes
(circled).
Align the holes in the side
plate with those in the
cylinder plates.
Half-tighten another
two 2 × 2mm screws
into the two holes on
the underside (circled).
This shows the position
of the left side plate after
being tted.
At this point, the front or
rear cylinder covers may
not be ush with the
side plate, as is the case
in this picture.
Place the left
side of the model
on a soft cloth
or towel, and
then repeat the
process to t the
right side plate.
Tightening the screws fully
should close this gap.
Turn the side
plate over and
apply a small
amount of instant
adhesive to the
backs of the pins.
37
FOCUS
76
When steam is fed into the
cylinders, water can accumulate
in them due to condensation,
especially when operating
in the cold, which can cause
trouble in steam locomotives.
The drain pipes at the bottom
of the cylinders allow this
build-up of water to be
discharged from the
pressure system.
The drainage pipe under a
cylinder of a real C57. Here you can see a C57 underway with its
drainage pipes fully opened, discharging
the water from the cylinders.
The front end of
each drainage
pipe is thinner
than the rear.
Apply some
synthetic rubber
adhesive to the
three pins on one
of the pipes and
insert them into the
circled holes on the
underside of the left
side plate.
Fit the other drainage pipe
to the bottom of the right
side plate in the same way. Apply some instant
adhesive to the ends
of the three pins of the
pipes, to make them
more secure.
Front
Drainage
pipes
Before the glue
dries, make sure the
drainage pipes are
vertical, as shown.
Complete
The drainage pipes
Step by step: Stage
Tools
Where your parts t
38
16
The piston rods
and crossheads
Left crosshead
Right crosshead
Left outer crosshead
Right outer crosshead
Crosshead pins × 2
Nuts × 2
Piston rods × 2
Pliers
Epoxy adhesive
Socket wrench (5.5mm)
1
CrossheadPiston rod
Insert a crosshead
pin into one of the
outer crossheads.
Tighten the nut.
A 5.5mm socket
wrench will make
this easier.
Place a nut onto the thread
of the crosshead pin.
Fit a crosshead pin and nut to the other
outer crosshead in the same way.
Your parts
Andere Handbücher für Model Space C57
4
Andere De Agostini Spielzeug Handbücher
De Agostini
De Agostini MODEL SPACE Soleil Royal Bedienungsanleitung
De Agostini
De Agostini Model Space MiG-29 Bedienungsanleitung
De Agostini
De Agostini Model Space MiG-29 Bedienungsanleitung
De Agostini
De Agostini Model Space MiG-29 Bedienungsanleitung
De Agostini
De Agostini MODEL SPACE SUZUKI GSX 1300R HAYABUSA Bedienungsanleitung
De Agostini
De Agostini Model Space T-72 Bedienungsanleitung
De Agostini
De Agostini Model Space MiG-29 Bedienungsanleitung
De Agostini
De Agostini Model Space T-72 Bedienungsanleitung
De Agostini
De Agostini MODEL SPACE Honda CB750 FOUR Bedienungsanleitung
De Agostini
De Agostini MODEL SPACE Honda CB750 FOUR Bedienungsanleitung
De Agostini
De Agostini Model Space T-72 Bedienungsanleitung
De Agostini
De Agostini Model Space MiG-29 Bedienungsanleitung
De Agostini
De Agostini MODEL SPACE SUZUKI GSX 1300R HAYABUSA Bedienungsanleitung
De Agostini
De Agostini Millennium Falcon 3 Series Bedienungsanleitung
De Agostini
De Agostini MODEL SPACE Honda CB750 FOUR Bedienungsanleitung
De Agostini
De Agostini Model Space Harley-Davidson FLSTF Fat Boy Bedienungsanleitung
De Agostini
De Agostini Model Space C57 Bedienungsanleitung
De Agostini
De Agostini Model Space T-72 Bedienungsanleitung
De Agostini
De Agostini Model Space D51 200 Bedienungsanleitung
De Agostini
De Agostini MODEL SPACE Honda CB750 FOUR Bedienungsanleitung
