Dell PowerEdge 1300 Installations- und Betriebshandbuch











Throughout this guide, blocks of text may be accompanied by an icon and printed in

bold type or in italic type. These blocks are notes, notices, cautions, and warnings,

and they are used as follows:

NOTE: A NOTE indicates important information that helps you make better use of your

computer system.





  !"

"#

$%&$%&!"

"#

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Computer

Corporation is strictly forbidden.

Trademarks used in this text: Dell, the DELL E COM logo, and PowerEdge are trademarks of

Dell Computer Corporation; Intel and Pentium are registered trademarks of Intel Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities

claiming the marks and names or their products. Dell Computer Corporation disclaims any propri-

etary interest in trademarks and trade names other than its own.

August 2000 P/N 54RJD Rev. A00

iii



Precautionary Measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Recording the System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Updating the ESM Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Updating the BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Saving RCU Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Installing Upgrade Microprocessors in the PowerEdge 1300 . . . . . . . . . . . . . . . . . 1-4

Installing Upgrade Microprocessors in the PowerEdge 2300 . . . . . . . . . . . . . . . . . 1-6

Installing Upgrade Microprocessors in the PowerEdge 4300 . . . . . . . . . . . . . . . . . 1-8

Installing Upgrade Microprocessors in the PowerEdge 4350 . . . . . . . . . . . . . . . . 1-11

Removing the Microprocessors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

Removing and Replacing the Guide Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

Removing and Replacing the Cooling Shroud . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15

Removing the Cooling Shroud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15

Replacing the Cooling Shroud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16

Installing the Upgrade Microprocessor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16

Installing a New Cooling Shroud in the PowerEdge 1300 and 2300 . . . . . . . . . . . 1-18

Reassembling and Checking the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19

 Figure 1-1. Removing the System Board Assembly . . . . . . . . . . . . . . . . . . . . . . 1-7

Figure 1-2. Removing the System Board Mounting Tray. . . . . . . . . . . . . . . . . . 1-10

Figure 1-3. Removing the System Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

Figure 1-4. Removing the Microprocessor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

Figure 1-5. Removing the Old Guide Bracket Assembly . . . . . . . . . . . . . . . . . . 1-14

Figure 1-6. Installing the New Guide Bracket Assembly . . . . . . . . . . . . . . . . . . 1-14

Figure 1-7. Removing the Cooling Shroud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16

Figure 1-8. Installing the Microprocessor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17

Figure 1-9. Installing a New Cooling Shroud Assembly . . . . . . . . . . . . . . . . . . . 1-18

support.dell.com Dell PowerEdge Systems — Microprocessor Upgrade 1-1





$%&'

!"

!

("

)*+,



This document provides procedures for upgrading the Intel®Pentium®II or III

microprocessors with either Intel Pentium II or Pentium III microprocessors in the

following Dell PowerEdge systems:

PowerEdge 1300

PowerEdge 2300

PowerEdge 4300

PowerEdge 4350

Installing one or more microprocessors in your server may involve the following

activities:

Verifying the basic input/output system (BIOS) revision and saving the current

configuration data

Accessing the system board (see your system’s Installation and Troubleshooting

Guide)

Replacing the system board mounting plate or tray (PowerEdge 2300 and 4300)

Installing the upgrade microprocessor

Installing the cooling shroud (if applicable)

Reassembling and checking the system

The upgrade procedure requires a #2 Phillips screwdriver. In addition, you should use

a wrist grounding strap for electrostatic discharge (ESD) protection. Read the safety

instructions in the following section.

1-2 Dell PowerEdge Systems —Microprocessor Upgrade

The contents of your kit will vary, depending on the PowerEdge system and the

number of microprocessors you are installing. Each kit will have one or more new

Pentium II or Pentium III microprocessor(s), diskettes containing the Resource

Configuration Utility (RCU), BIOS, embedded server management (ESM) firmware,

and diagnostics. Also included, for some system models, is a cooling shroud and

mounting hardware or a replacement system board mounting plate or tray.



Before you perform any of the procedures in this document, take a few moments to

read the following warning for your personal safety and to prevent damage to the

computer system from ESD.

$%&(%- %'%*.*(-/'%(0

1 '2

Before you start to work on the computer, perform the following steps in the

sequence listed:

1. Turn off your computer and any devices.

2. Ground yourself by touching an unpainted metal surface on the chassis, such as

the metal around the card-slot openings at the back of the computer, before

touching anything inside your computer.

While you work, periodically touch an unpainted metal surface on the computer

chassis to dissipate any static electricity that might harm internal components.

3. Disconnect your computer and devices from their power sources. Also, discon-

nect any telephone or telecommunication lines from the computer.

Doing so reduces the potential for personal injury or shock.

In addition, take note of these safety guidelines when appropriate:

When you disconnect a cable, pull on its connector or on its strain-relief loop,

not on the cable itself. Some cables have a connector with locking tabs; if

you are disconnecting this type of cable, press in on the locking tabs before

disconnecting the cable. As you pull connectors apart, keep them evenly aligned

to avoid bending any connector pins. Also, before you connect a cable, make

sure both connectors are correctly oriented and aligned.

Handle components and cards with care. Don’t touch the components or

contacts on a card. Hold a card by its edges or by its metal mounting bracket.

Hold a component such as a microprocessor chip by its edges, not by its pins.

If your system has two microprocessors installed, the secondary microprocessor

must be the same type and have the same operating frequency and cache size as the

primary microprocessor. For example, if the system you are installing has a

500-megahertz (MHz) Pentium III primary microprocessor, the secondary

microprocessor must also be a 500-MHz Pentium III microprocessor.

support.dell.com Dell PowerEdge Systems —Microprocessor Upgrade 1-3

/'

'/

3





4"





Before shutting down your system, perform these preliminary steps:

Record the system configuration

Update the ESM firmware

Update the BIOS (if necessary)

Use the RCU diskette (provided in the kit) to save the RCU configuration settings

(see your User’s Guide for information).



View the system configuration screens in the System Setup program and make a

record of the settings.



If an ESM firmware diskette is included with your kit, update your ESM firmware with

the version contained on that diskette by performing the following steps. The latest

version of the ESM firmware is also available online at http://support.dell.com.

1. Insert the ESM firmware diskette provided in the upgrade kit into the diskette

drive.

2. Reboot the system.

3. After the system completes the boot routine, follow the instructions on the

screen.

4. After the Successfully Completed Done message appears on the screen,

remove the ESM firmware diskette from the diskette drive and follow the

instructions on the screen to reboot the system.

1-4 Dell PowerEdge Systems —Microprocessor Upgrade

 !

If a BIOS diskette is included with your kit, update your BIOS with the version

contained on that diskette by performing the following steps. The latest version of

the BIOS is also available online at http://support.dell.com.

1. Insert the BIOS diskette provided in the upgrade kit into the diskette drive.

2. Reboot the system.

3. After the system completes the boot routine, follow the instructions on the

screen.

4. After the BIOS has been successfully installed message appears on

the screen, remove the BIOS diskette from the diskette drive and follow the

instructions on the screen to reboot the system.

"

Use the RCU to save the current system configuration settings by performing the

following steps:

1. Insert the RCU diskette into the diskette drive and reboot the system.

2. When the welcome screen appears, press <Enter>.

The main menu appears.

3. Select Step 5: Save and Exit, and then follow the online instructions to save the

current system configuration information.

NOTE: The RCU recognizes microprocessors operating at 450 MHz and faster.

The latest version of the RCU is available online at http://support.dell.com.





To upgrade to Pentium II or Pentium III microprocessors in the PowerEdge 1300, per-

form the following steps:

1. Access the system board, which involves the following steps:

a. Disconnecting power and peripheral cables.

b. Removing the covers.

c. Rotating the power supply.

See your system Installation and Troubleshooting Guide for instructions.

2. Remove the microprocessors.

See “Removing the Microprocessors”, found later in this document.

support.dell.com Dell PowerEdge Systems —Microprocessor Upgrade 1-5

3. Remove and replace the guide brackets.

See “Removing and Replacing the Guide Brackets”, found later in this

document.

4. Remove the cooling shroud.

See “Removing and Replacing the Cooling Shroud”, found later in this

document.

5. Install the upgrade microprocessor.

See “Installing the Upgrade Microprocessors”, found later in this document.

6. Replace the cooling shroud.

See “Removing and Replacing the Cooling Shroud”, found later in this

document.

If the upgrade kit comes with a new cooling shroud, you must install the new

cooling shroud. See “Installing a New Cooling Shroud”, found later in this

document.

7. Reassemble and check the system, as follows:

a. Rotate the power supply back into position, making sure that the securing

tab snaps into place.

b. Replace the covers and front bezel. Reconnect your computer and peripher-

als to their power sources and turn them on.

As the system boots, it detects the presence of the new microprocessor

and automatically changes the system configuration information in the Sys-

tem Setup program.

NOTE: After you remove and replace the cover of a PowerEdge 1300 system,

the chassis intrusion detector causes the following message to be displayed at

the next system start-up:

ALERT! Cover was previously removed.

c. Enter the System Setup program and confirm that the top line in the system

data area correctly identifies the installed microprocessor(s). By default, the

serial numbers of Pentium III microprocessors are not displayed. See the

procedures in “Using the System Setup Program”in your User's Guide for

accessing and modifying entries in the System Setup screens.

d. Reset the chassis intrusion detector while in the System Setup program by

changing Chassis Intrusion to Not Detected.

NOTE: If a setup password has been assigned by someone else, contact your

network administrator for information on resetting the chassis intrusion detector.

1-6 Dell PowerEdge Systems —Microprocessor Upgrade

e. Run the Dell Diagnostics to verify that the new microprocessor is operating

correctly.

See your User’s Guide and your computer Installation and Troubleshooting

Guide for additional information on running the Dell Diagnostics and

troubleshooting any problems that may occur.





To upgrade to Pentium II or Pentium III microprocessors in the PowerEdge 2300, per-

form the following steps.

$%&5

!"



)'25

+)6-6+

5



NOTES: If you are installing a 600 MHz (or greater) microprocessor in your

PowerEdge 2300, the system board mounting plate must be replaced. A replacement

mounting plate is provided with the upgrade kit.

If you are upgrading a PowerEdge 2300 with one or two microprocessors with an

operating frequency less than 600 MHz, you do not need to replace the system board

mounting plate.

1. Access the system board, which involves the following steps:

a. Disconnecting power and peripheral cables.

b. Removing the covers.

c. Removing the front bezel.

d. Removing the cooling fan shroud.

e. Replacing the system board mounting plate or tray. Applies only when

installing 600 MHz or greater microprocessors.

See your system Installation and Troubleshooting Guide for specific instructions,

if needed.

support.dell.com Dell PowerEdge Systems —Microprocessor Upgrade 1-7

2. If you are installing a 600 MHz or greater microprocessor, replace the system

board mounting plate as follows.

a. Unlock and remove the front bezel.

b. Remove the right- and left-side computer covers.

c. Record the location and disconnect all external peripheral cables from their

connectors on the back of the computer.

d. Record the location of any internal expansion card cables, and then record

the slot number assignments and remove all the expansion cards.

Place the expansion cards in antistatic bags or on a grounded antistatic mat

or other antistatic surface.

e. Record the locations and disconnect all internal cables attached to the sys-

tem board.

f. At the left side of the system, locate and remove the three screws that

secure the system board and mounting plate to the chassis (see Figure 1-1).



mounting

screws (3)

system board and

mounting-plate assembly

Dieses Handbuch passt für folgende Modelle

Andere Dell Server Handbücher

Dell

Dell PowerEdge systems 6300 Stücklistenhandbuch

Dell

Dell PowerEdge R720 t Bedienungsanleitung

Dell

Dell Force10 C150 Bedienungsanleitung

Dell

Dell Dimension 4100 Leitfaden

Dell

Dell PowerEdge R210 Technisches Handbuch

Dell

Dell PowerEdge 4200 Series Bedienungsanleitung

Dell

Dell PowerEdge M630 Bedienungsanleitung

Dell

Dell EMC VxFlex Ready Node Bedienungsanleitung

Dell

Dell PowerEdge 1655MC Technisches Handbuch

Dell

Dell PowerEdge T630 Bedienungsanleitung

Dell

Dell PowerVault DL4000 Bedienungsanleitung

Dell

Dell PowerEdge 1650 Leitfaden

Dell

Dell EMC PowerEdge M640 Handbuch

Dell

Dell PowerEdge R510 Bedienungsanleitung

Dell

Dell X95FF Handbuch

Dell

Dell PowerEdge R805 System Allgemeine Anweisungen

Dell

Dell PowerEdge C8000 Bedienungsanleitung

Dell

Dell VxRail G560 Bedienungsanleitung

Dell

Dell PowerEdge 2550 Bedienungsanleitung

Dell

Dell PowerEdge R310 Bedienungsanleitung

Dell

Dell PowerEdge 1400SC Technisches Handbuch

Dell

Dell PowerEdge PDU Managed LED Bedienungsanleitung

Dell

Dell PowerEdge 2650 Bedienungsanleitung

Dell

Dell PowerEdge T610 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung

Vertiv

Vertiv Avocent ACS6000 Montage- und Wartungsanleitung

A & T Internationale

A & T Internationale Xserve Service-Handbuch