Dell PowerEdge 1650 Bedienungsanleitung

www.dell.com | support.dell.com

Dell™ Systems

Rack Installation Guide

5X860et0.fm Page 1 Monday, October 21, 2002 11:48 AM

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury,

or death.

____________________

Information in this document is subject to change without notice.

Reproductioninanymannerwhatsoever without the written permissionofDellComputerCorporationisstrictlyforbidden.

Trademarks used in this text: Dell, the DELL logo, VersaRails, and RapidRails are trademarks of Dell Computer

Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and

names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names

other than its own.

October 2002 P/N 5X860 Rev. A00

5X860et0.fm Page 2 Monday, October 21, 2002 11:48 AM

Contents 3

Contents

CAUTION: Safety Instructions . . . . . . . . . . . . . . . . . . 1-1

Rack Mounting of Systems . . . . . . . . . . . . . . . . . . . 1-1

Installation Instructions . . . . . . . . . . . . . . . . . . . . . . 1-2

Rack Requirements for VersaRails . . . . . . . . . . . . . . . 1-3

Four-Post Rack Installation . . . . . . . . . . . . . . . . . . . . 1-3

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Recommended Tools and Supplies. . . . . . . . . . . . . . . . 1-3

RapidRails Rack Kit Contents. . . . . . . . . . . . . . . . . . 1-4

VersaRails Rack Kit Contents . . . . . . . . . . . . . . . . . . 1-4

Installation Tasks. . . . . . . . . . . . . . . . . . . . . . . . 1-5

Removing the Rack Doors. . . . . . . . . . . . . . . . . . . . 1-5

Marking the Rack . . . . . . . . . . . . . . . . . . . . . . . 1-6

Installing the RapidRails Slide Assemblies . . . . . . . . . . . 1-7

Installing the VersaRails Slide Assemblies . . . . . . . . . . . 1-9

Installing the System in the Rack . . . . . . . . . . . . . . . 1-10

Installing the Cable-Management Arm . . . . . . . . . . . . 1-11

Routing Cables . . . . . . . . . . . . . . . . . . . . . . . . 1-14

Replacing the Rack Doors. . . . . . . . . . . . . . . . . . . 1-16

Two-Post Rack Installation. . . . . . . . . . . . . . . . . . . . 1-16

Recommended Tools and Supplies. . . . . . . . . . . . . . . 1-16

Rack Kit Contents . . . . . . . . . . . . . . . . . . . . . . 1-17

Two-Post Rack Installation Tasks . . . . . . . . . . . . . . . 1-17

Marking the Rack . . . . . . . . . . . . . . . . . . . . . . 1-18

Installing the Slide Assemblies in the Rack . . . . . . . . . . 1-19

Installing the System in the Rack . . . . . . . . . . . . . . . 1-25

Installing the Cable-Management Arm . . . . . . . . . . . . 1-26

Routing Cables . . . . . . . . . . . . . . . . . . . . . . . . 1-26

5X860ey0.fm Page 3 Monday, October 21, 2002 11:48 AM

4Contents

Index

Figures

Figure 1-1. RapidRails Rack Kit Contents . . . . . . . . . 1-4

Figure 1-2. VersaRails Rack Kit Contents . . . . . . . . . 1-5

Figure 1-3. One Rack Unit . . . . . . . . . . . . . . . . . 1-6

Figure 1-4. Marking the Vertical Rails . . . . . . . . . . 1-7

Figure 1-5. Installing the RapidRails Slide Assemblies . . . 1-8

Figure 1-6. Installing the VersaRails Slide Assemblies . . . 1-9

Figure 1-7. Installing the System in the Rack

(RapidRails or VersaRails) . . . . . . . . . 1-11

Figure 1-8. Installing the Cable-Management Arm . . . 1-12

Figure 1-9. Opening the Wire Covers . . . . . . . . . . 1-13

Figure 1-10. Installing the Power Cord Strain Relief . . . 1-14

Figure 1-11. Routing Cables . . . . . . . . . . . . . . . 1-15

Figure 1-12. Two-Post Rack Kit Components . . . . . . . 1-17

Figure 1-13. Two-Post, Open-Frame Relay Rack

Universal-Hole Spacing . . . . . . . . . . . 1-18

Figure 1-14. Two-Post, Open-Frame Relay Rack

Wide-Hole Spacing . . . . . . . . . . . . . 1-19

Figure 1-15. Installing the Slide Assemblies for

Center-Mount Configuration . . . . . . . . 1-21

Figure 1-16. Installing the Stiffening Bracket (shown in

3-inch rack position) . . . . . . . . . . . . 1-22

Figure 1-17. Rotating the Front Mounting Bracket for

Flush-Mount Installation . . . . . . . . . . 1-23

Figure 1-18. Installing the Slide Assemblies for

Flush-Mount Configuration . . . . . . . . . 1-24

5X860ey0.fm Page 4 Monday, October 21, 2002 11:48 AM

Rack Installation Guide 1-1

CAUTION: Safety Instructions

Use the following safety guidelines to help ensure your own personal safety and to help

protect your system and working environment from potential damage. For complete safety

information, see the System Information Guide.

Rack Mounting of Systems

Observe the following precautions for rack stability and safety.

Systems are considered to be components in a rack. Thus, "component" refers to any

system as well as to various peripherals or supporting hardware.

CAUTION: Installing systems in a rack without the front and side stabilizers

installed could cause the rack to tip over, potentially resulting in bodily injury

under certain circumstances. Therefore, always install the stabilizers before

installing components in the rack.

After installing system/components in a rack, never pull more than one

component out of the rack on its slide assemblies at one time. The weight of

more than one extended component could cause the rack to tip over and may

result in serious injury.

NOTE: Your system is safety-certified as a free-standing unit and as a component for

use in a Dell™ rack cabinet using the customer rack kit. The installation of your

system and rack kit in any other rack cabinet has not been approved by any safety

agencies. It is your responsibility to ensure that the final combination of system and

rack complies with all applicable safety standards and local electric code

requirements. Dell disclaims all liability and warranties in connection with such

combinations.

• System rack kits are intended to be installed in a rack by trained service technicians. If

you install the kit in any other rack, be sure that the rack meets the specifications of a

Dell rack.

CAUTION: Do not move racks by yourself. Due to the height and weight of the

rack, a minimum of two people should accomplish this task.

• Before working on the rack, make sure that the stabilizers are secured to the rack,

extended to the floor, and that the full weight of the rack rests on the floor. Install

front and side stabilizers on a single rack or front stabilizers for joined multiple racks

before working on the rack.

• Always load the rack from the bottom up, and load the heaviest item in the rack first.

• Make sure that the rack is level and stable before extending a component from the

rack.

5X860eb0.fm Page 1 Monday, October 21, 2002 11:49 AM

1-2 Rack Installation Guide

www.dell.com | support.dell.com

Installation Instructions

This installation guide provides instructions for trained service technicians installing one or

more systems in a rack cabinet or in an open-frame relay rack. The RapidRails™ rack kit can

be installed in all the system manufacturer’s rack cabinets without tools, and the

VersaRails™ rack kit can be installed in most industry-standard rack cabinets. The

procedures for installing both RapidRails and VersaRails rack kits are similar. One rack kit is

required for each system to be installed in the rack cabinet.

This guide includes procedures for the following rack kits:

• RapidRails kit in a four-post rack cabinet

• VersaRails kit in a four-post rack cabinet

• Two-post kit (installed in either center-mount or flush-mount configuration)

For ease in troubleshooting and the identification of system health, some rack kits include a

status-indicator cable assembly that extends the information from the two-color status

indicators on the front and back panels to the back of the cable-management arm. For more

information on these indicators, see the User’s Guide.

Before attempting this installation, you should read through this entire document carefully.

CAUTION: Do not install rack kit components designed for another system. Use

only the rack kit for your system. Using the rack kit for another system may

result in damage to the system and personal injury to yourself and to others.

• Use caution when pressing the component rail release latches and sliding a

component into or out of a rack; the slide rails can pinch your fingers.

• After a component is inserted into the rack, carefully extend the rail into a locking

position, and then slide the component into the rack.

• Do not overload the AC supply branch circuit that provides power to the rack. The

total rack load should not exceed 80 percent of the branch circuit rating.

• Ensure that proper airflow is provided to components in the rack.

• Do not step on or stand on any component when servicing other components in a

rack.

CAUTION: Safety Instructions (continued)

5X860eb0.fm Page 2 Monday, October 21, 2002 11:49 AM

Rack Installation Guide 1-3

Rack Requirements for VersaRails

NOTICE: The VersaRails rack kit is intended to be installed by trained service technicians in a

rack that meets the specifications of American National Standards Institute (ANSI)/Electronic

Industries Association (EIA) standard ANSI/EIA-310-D-92, International Electrotechnical

Commission (IEC) 297, and Deutsche Industrie Norm (DIN) 41494. One rack kit is required for

each system that is installed in a rack.

Four-Post Rack Installation

Before attempting this installation, you should read through this entire procedure carefully.

Before You Begin

Before you begin installing your system in the rack, carefully read "Safety Instructions" as

well as the safety instructions found in your system’s System Information document for

additional information.

CAUTION: When installing multiple systems in a rack, complete all of the

procedures for the current system before attempting to install the next system.

CAUTION: Rack cabinets can be extremely heavy and move easily on their

casters. They have no brakes. Use extreme caution while moving the rack

cabinet. Retract the leveling feet when relocating the rack cabinet. Avoid long

or steep inclines or ramps where loss of cabinet control may occur. Extend the

leveling feet for support and to prevent the cabinet from rolling.

NOTE: For instructions on installing the system itself, see "Installing the System in the Rack."

Important Safety Information

Observe the safety precautions in the following subsections when installing your system in

the rack.

CAUTION: You must strictly follow the procedures in this document to protect

yourself as well as others who may be involved. Your system may be very large

and heavy and proper preparation and planning are important to prevent injury

to yourself and to others. This becomes increasingly important when systems are

installed high up in the rack.

Recommended Tools and Supplies

You may need the following tools and supplies to install the system in a four-post rack:

• #2 Phillips screwdriver

• Masking tape or a felt-tip pen, for use in marking the mounting holes to be used

5X860eb0.fm Page 3 Monday, October 21, 2002 11:49 AM

1-4 Rack Installation Guide

www.dell.com | support.dell.com

RapidRails Rack Kit Contents

The RapidRails rack kit includes the following items (see Figure 1-1):

• One pair of RapidRails slide assemblies

• One cable-management arm

• Two stop blocks (left and right)

• One status-indicator cable assembly

• Releasable tie wraps (not shown in Figure 1-1)

Figure 1-1. RapidRails Rack Kit Contents

VersaRails Rack Kit Contents

The VersaRails rack kit includes the following items (see Figure 1-2):

• One pair of VersaRails slide assemblies

• One cable-management arm

• Two stop blocks (left and right)

• One status-indicator cable assembly

• Ten 10-32 x 0.5-inch flange-head Phillips screws

• Releasable tie wraps (not shown in Figure 1-2)

NOTE: The nonmetric screws described in illustrations and in procedural steps are

identified by size and number of threads-per-inch. For example, a #10 Phillips-head

screw with 32 threads per inch is identified as a 10-32 screw.

slide assemblies (2)

cable-management arm

stop blocks (2)

status-indicator cable

5X860eb0.fm Page 4 Monday, October 21, 2002 11:49 AM

Rack Installation Guide 1-5

Figure 1-2. VersaRails Rack Kit Contents

Installation Tasks

Installing a rack kit involves performing the following tasks in their numbered order:

1Removing the rack doors

2Marking the rack

3Installing the slide assemblies in the rack

• RapidRails slide assemblies

• VersaRails slide assemblies

4Installing the system in the rack

5Installing the cable-management arm

6Routing cables

7Replacing the rack doors

Removing the Rack Doors

See the procedures for removing doors in the documentation provided with your rack

cabinet.

CAUTION: Because of the size and weight of the rack cabinet doors, never

attempt to remove or install them by yourself.

CAUTION: Store the two doors where they will not injure someone if the doors

accidently fall over.

slide assemblies (2)

10-32 x 0.5-inch flange-head

Phillips screws (10)

cable-management arm

stop blocks (2)

status-indicator cable

5X860eb0.fm Page 5 Monday, October 21, 2002 11:49 AM

1-6 Rack Installation Guide

www.dell.com | support.dell.com

Marking the Rack

You must allow 1 U (44 mm, or 1.75 inches) of vertical space for each system you install in

the rack. Rack cabinets that meet EIA-310 standards have an alternating pattern of three

holes per rack unit with center-to-center hole spacing (beginning at the top hole of a 1-U

space) of 15.9 mm, 15.9 mm, and 12.7 mm (0.625 inch, 0.625 inch, and 0.5 inch) for the

front and rear vertical rails (see Figure 1-3). Rack cabinets may have round or square holes.

NOTE: The vertical rails may be marked by horizontal lines and numbers in 1-U

increments. If you wish, you can make a note of the number marking on the rack’s

vertical rail. It is not necessary to mark or place tape on the rack. If you choose this

method, skip ahead to the procedure "Installing the RapidRails Slide Assemblies."

Figure 1-3. One Rack Unit

CAUTION: If you are installing more than one system, install the slide assemblies

so that the first system is installed in the lowest available position in the rack.

To mark the rack, perform the following steps:

1Place a mark on the rack’s front vertical rails where you want to locate the bottom of

the system you are installing in the rack cabinet.

The bottom of each 1-U space is at the middle of the narrowest metal area between

holes (marked with a horizontal line on some rack cabinets—see Figure 1-3).

1 U (44 mm or 1.75 inches)

12.7 mm (0.5 inch)

15.9 mm (0.625 inch)

12.7 mm (0.5 inch)

5X860eb0.fm Page 6 Monday, October 21, 2002 11:49 AM

Andere Handbücher für PowerEdge 1650

Inhaltsverzeichnis

Sprachen:

Andere Dell Server Handbücher

Dell

Dell EMC PowerEdge R740 Handbuch

Dell

Dell PowerEdge R320 Bedienungsanleitung

Dell

Dell PowerEdge 1500SC Technisches Handbuch

Dell

Dell PowerEdge C8000 Bedienungsanleitung

Dell

Dell PowerEdge T710 Bedienungsanleitung

Dell

Dell PowerEdge C5220 Kurzanleitung

Dell

Dell PowerEdge XR5610 Handbuch

Dell

Dell DL4300 Bedienungsanleitung

Dell

Dell Force10 MXL Blade Bedienungsanleitung

Dell

Dell PowerEdge 1955 Bedienungsanleitung

Dell

Dell PowerEdge T320 Kurzanleitung

Dell

Dell PowerEdge R210 II Betriebsanleitung

Dell

Dell POWEREDGE 1900 Bedienungsanleitung

Dell

Dell POWEREDGE 1900 Service-Handbuch

Dell

Dell VEP4600 Bedienungsanleitung

Dell

Dell PowerEdge R820 Bedienungsanleitung

Dell

Dell PowerEdge 2410 Bedienungsanleitung

Dell

Dell PowerEdge 1850 Technisches Handbuch

Dell

Dell PowerEdge M520 Bedienungsanleitung

Dell

Dell PowerEdge M910 Kurzanleitung

Dell

Dell PowerEdge 1400SC Bedienungsanleitung

Dell

Dell PowerEdge 2300 Bedienungsanleitung

Dell

Dell PowerVault NX3000 Bedienungsanleitung

Dell

Dell PowerEdge 2410 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung

Vertiv

Vertiv Avocent ACS6000 Montage- und Wartungsanleitung

A & T Internationale

A & T Internationale Xserve Service-Handbuch