DFI CS62-TC Bedienungsanleitung
CS62-TC
Rev. A+
System Board Users Manual
Carte Mère Manuel Pour Utilisateur
System-Platine Benut erhandbuch
Tablero Electrónico del Sistema Manual del Usuario
48400116
Copyright
This publication contains information that is protected by copyright.
No part of it may be reproduced in any form or by any means or
used to make any transformation/adaptation without the prior
written permission from the copyright holders.
This publication is provided for informational purposes only. The
manufacturer makes no representations or warranties with respect to
the contents or use of this manual and specifically disclaims any
express or implied warranties of merchantability or fitness for any
particular purpose. The user will assume the entire risk of the use or
the results of the use of this document. Further, the manufacturer
reserves the right to revise this publication and make changes to its
contents at any time, without obligation to notify any person or
entity of such revisions or changes.
© 001. All Rights Reserved.
Trademarks
Microsoft® MS-DOS®, WindowsTM, Windows® 95, Windows® 98,
Windows® 98 SE, Windows® ME, Windows® 000 and Windows
NT® 4.0 are registered trademarks of Microsoft Corporation. Intel®,
Pentium® III and CeleronTM are registered trademarks of Intel
Corporation. Award is a registered trademark of Award Software,
Inc. Other trademarks and registered trademarks of products
appearing in this manual are the properties of their respective
holders.
Caution
To avoid damage to the system:
Use the correct AC input voltage range.
To reduce the risk of electric shock:
Unplug the power cord before removing the system chassis
cover for installation or servicing. After installation or servicing,
cover the system chassis before plugging the power cord.
Battery:
Danger of explosion if battery incorrectly replaced.
Replace only with the same or equivalent type recommend by
the manufacturer.
Dispose of used batteries according to the battery
manufacturers instructions.
Joystick or MIDI port:
Do not use any joystick or MIDI device that requires more than
10A current at 5V DC. There is a risk of fire for devices that
exceed this limit.
FCC and DOC Statement on Class B
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio TV technician for
help.
Notice:
1. The changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
. Shielded interface cables must be used in order to comply with
the emission limits.
4
Quick Setup Guide
Quick Setup
Guide
Table of Contents
Chapter 1
Quick Setup Guide.............................................
Chapter
English......................................................................
Chapter 3
Français (French).................................................
Chapter 4
Deutsch (German)................................................
Chapter 5
Español (Spanish)..................................................
5
4
41
59
77
5
Quick Setup Guide
Quick Setup
Guide
Chapter 1 - Quick Setup Guide
Table of Contents
1.1 System Board Layout..................................................................................................
1. Jumpers.....................................................................................................................................
1.3 Ports and Connectors................................................................................................
1.4 Award BIOS Setup Utility.......................................................................................
6
7
10
19
Note:
The users manual in the provided CD contains detailed information
about the system board. If, in some cases, some information doesnt
match those shown in this manual, this manual should always be
regarded as the most updated version.
6
Quick Setup Guide
Quick Setup
Guide
1.1 System Board Layout
7
Quick Setup Guide
Quick Setup
Guide
1. Jumpers
1. .1 CPUs Front Side Bus - JP and JP3
Warning:
Some processors, when overclocked, may result to the processors or
systems instability and are not guaranteed to provide better system
performance. If you are unable to boot your system due to
overclocking, make sure to set these umpers back to their default
settings.
CPU/DIMM
Auto*
66/100MHz
100/100MHz
133/100MHz
133/133MHz
JP
1- On
-3 On
All Off
All Off
-3 On
JP3
1- On
-3 On
-3 On
All Off
All Off
* denotes default setting
-3 On
1- On All Off
3
1
3
1
3
1
8
Quick Setup Guide
Quick Setup
Guide
1. . Clear CMOS Data - JP4
1. .3 Wake-On-Keyboard / Wake-On-Mouse - JP1
1- On:
Disable the Wake-On-KB/Mouse
function (default)
-3 On:
Enable the Wake-On-KB/Mouse
function
Important:
The 5VSB power source of your power supply must support
≥
720mA.
1
3
1
3
-3 On:
Clear CMOS Data
1- On: Normal
(default)
1 3
1 3
9
Quick Setup Guide
Quick Setup
Guide
1. .4 Wake-On-USB Keyboard - JP5 and JP6
1- On:
Disable the Wake-On-USB
Keyboard function
(default)
-3 On:
Enable the Wake-On-USB
Keyboard function
Important:
If you are using the Wake-On-USB Keyboard function for 2 USB
ports, the 5VSB power source of your power supply must
support
≥
1.5A.
If you are using the Wake-On-USB Keyboard function for 4 USB
ports, the 5VSB power source of your power supply must
support
≥
2A.
3
1
3
1
JP6 - for the USB keyboard that is connected to the USB 1 or USB
port.
JP5 - for the USB keyboard that is connected to the USB 3 or USB 4
port.
USB KB Wake-Up From S3 in the Power Management Setup submenu
of the BIOS must also be enabled.
10
Quick Setup Guide
Quick Setup
Guide
1.3 Ports and Connectors
1.3.1 PS/ Mouse and PS/ Keyboard Ports
Make sure to turn off your computer
prior to connecting or disconnecting a
mouse or keyboard. Failure to do so may
damage the system board.
PS/ Mouse
PS/ Keyboard
1.3. Parallel Port
Parallel Port
Inhaltsverzeichnis
Andere DFI Hauptplatine Handbücher
DFI
DFI CR101-D Bedienungsanleitung
DFI
DFI LanParty NFII Ultra B Bedienungsanleitung
DFI
DFI AZ30-TC Bedienungsanleitung
DFI
DFI 586STE Bedienungsanleitung
DFI
DFI K6BV3+ Bedienungsanleitung
DFI
DFI CA61 Bedienungsanleitung
DFI
DFI 855GME-MGF Bedienungsanleitung
DFI
DFI G586VPM Bedienungsanleitung
DFI
DFI BT160 Bedienungsanleitung
DFI
DFI SB102-D Bedienungsanleitung
DFI
DFI M8MP553 Bedienungsanleitung
DFI
DFI HD330-H81 Bedienungsanleitung
DFI
DFI CP100-NRM Bedienungsanleitung
DFI
DFI G586SP Bedienungsanleitung
DFI
DFI HD636-H81CS Bedienungsanleitung
DFI
DFI LanParty X58-T3eH8 Bedienungsanleitung
DFI
DFI WL051 Bedienungsanleitung
DFI
DFI ICX610-C621A Bedienungsanleitung
DFI
DFI BW171 Bedienungsanleitung
DFI
DFI PW65 Series Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
Biostar
Biostar M7VIT Bravo Bedienungs- und Montageanleitung
