Digital Equipment 100BaseFX Mod-MAC Bedienungsanleitung

EK-DLXFX-IM. A01

Installing and Cabling the 100BaseFX Mod-MAC (DLXFX)

Introduction

The 100BaseFX Mod-MAC is part of the Mod-MAC product family (which includes the 100BaseTX and

10BaseFL). It provides connectivity between a DIGITAL MultiSwitch 612EX and network devices using

100BaseFX Multimode Fiber (MMF). The 100BaseFX Mod-MAC only operates in the DIGITAL MultiSwitch

612EX. As illustrated above, the 100BaseFX Mod-MAC contains a transmit (1) and receive (2) connector.

Installation Procedure

Before you install a 100BaseFX Mod-MAC, make sure that the module has no power connected to it. The

100BaseFX Mod-MACs are not hot-swappable. To install the 100BaseFX Mod-MAC, complete the following

steps. A Phillips-head screwdriver is required.

1Remove the dust cap from the module’s modular interface connector.

2Hold the 100BaseFX Mod-MAC by its bezel so that it is parallel with a slot opening on the module.

3Insert the 100BaseFX Mod-MAC and align its sides with the guide in the module’s slot opening.

4Push the 100BaseFX Mod-MAC into the slot until it is firmly seated inside the module.

5Align and securely fasten the two Phillips-head screws on the 100BaseFX Mod-MAC bezel.

NPB-0600-96F

NPB-0611-96F

6Insert the transmit (1) and receive (2) 100BaseFX cable connectors into the transmit and

receive100BaseFX Mod-MAC port connectors, respectively , respectively.

When the module is powered on, the following 100BaseFX Mod-MAC LEDs become operational:

Reference

If the LEDs do not operate as described, refer to the troubleshooting information in the DIGITAL MultiSwitch

612EX Installation and Configuration manual. The manual provides safety and product specification information.

The informationisalso available on the DigitalEquipmentCorporation Network Products EngineeringHome Page

on the World Wide Web at the following addresses:

North America: http://www.networks.digital.com

Europe: http://www.networks.europe.digital.com

Australia: http://www.digital.com.au/networks

Digital, and the DIGITAL logo are trademarks of Digital Equipment Corporation.

Item Name Description

1 Activity LED Flickers in response to traffic on this port.

2 Port Status Is turned off if there is no connection; blinks if the port has

been disabled by management; steady on if there is a

connection.

NPB-0610-96F

NPB-0609-96F

DLXFX-MA

Inhaltsverzeichnis

Andere Digital Equipment PCI-Karte Handbücher

Digital Equipment

Digital Equipment 9FX Vision 330 Bedienungsanleitung

Digital Equipment

Digital Equipment EtherWORKS Turbo PCI Bedienungsanleitung

Digital Equipment

Digital Equipment EtherWORKS Turbo PCI Bedienungsanleitung

Digital Equipment

Digital Equipment Fast EtherWORKS DE500-BA Bedienungsanleitung

Digital Equipment

Digital Equipment 10BaseFL Mod-MAC Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung