Digital Watchdog Snapit DWC-V4363D Bedienungsanleitung

ABOUT MANUAL

Before installing and using the camera, please read this manual carefully.

Be sure to keep it handy for future reference.

Vandal-Proof Dome Camera

DWC-V4363D/ V4363DB

DWC-V4363TIR/ V4363TIRB

DWC-V4363DH

12132012

PRECAUTIONS

FCC COMPLIANCE

Do not open or modify.

Do not open the case except during maintenence and installation, for it may be dangerous and can

cause damages.

Do not put objects into the unit.

Keep metal objects and flammable substances from entering the camera.

It can cause fire, short-circuits, or other damages.

Be careful when handling the unit.

To prevent damages, do not drop the camera or subject it to shock or vibration.

Do not install near electric or magnetic fields.

Protect from humidity and dust.

Protect from high temperature.

Be careful when installing near the ceiling of kitchen or a boiler room, as the temperature may rise

to high levels.

Cleaning:

To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.

Mounting Surface:

The material of the mounting surface must be strong enough to support the camera.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against

harmful interference, when the equipment is operated in a residential environment. This equipment

generates, uses, and radiates radio frequency energy; and if it is not installed and used in accordance

with the instruction manual, it may cause harmful interference to radio communications.

WARNING: Changes or modifications are not expressly approved by the manufacturer.

TABLE OF CONTENTS

Introduction

Installation

Module OSD Menu

Troubleshooting

Warranty Information

Specifications

Features

Parts and Descriptions

Dimensions

Inside the Box

Mount Installation Instructions

Connecting to Monitors

Adjusting the Camera Lens

8-13

14-15

18-29

31-32

33-36

Adjusting the 3-Axis Gimbal 17

FEATURES*

1/3” CCD

620 TV Lines (B&W), 600 TV Lines (Color)

3.3~12mm Varifocal Auto Iris Lens

70ft Range IR with Intelligent Camera Sync [DWC-V4363TIR Only]

Electronic Day and Night [DWC-V4363D & DWC-V4363DH]

TDN (True Day and Night / IR Cut Filter) [DWC-V4363TIR Only]

Smart DNR (Digital Noise Reduction)

DRC (Dynamic Range Compressor)

Star-Light (Super Low Light Technology)

HME (Highlight Masking Exposure)

Programmable Privacy Zones & Motion Detection

Easy Icon Driven OSD Menu with Built-In Joystick

IP68 Certified

Heater Built-in [DWC-V4363DH Only]

Junction Box Included

UTP & RS485 Built-In

Auto Sensing 12VDC or 24VAC with Line Lock

Secondary Video-BNC Output

PART & DESCRIPTIONS*

1Lens

Power Input Connector (Dual Voltage)

UTP

RS-485

Primary Video-BNC Output Connector

Camera Control Board

Bubble Dome Cover

Upper Case

Flush Mount Base

Surface Mount Base / Junction Box

Assembly Screws (#8 - 32 x 0.75)

Secondary Video-BNC Output Connector

Safety Wire

Mounting Screws

NO IR IR

DIMENSIONS IN MILLIMETERS (IN)*

101(3.98”)

137(5.39”)

17(0.67”)

28(1.1”)

54(2.13”)

98.8(3.89”)

121

(4.76”)

118.8

(4.68”)

139(5.47”)139(5.47”)

36(1.42”)

29(1.41”)

53.8(2.12”)

Flush Mount

Surface Mount

121

(4.76”)

INSIDE THE BOX*

Included with Snapit Vandal Dome Camera

User Manual

Mounting Template

4 Machine Screws and 4 Dry Wall Anchors

TORX-T20 Wrench

L-Wrench

TORX-T20 Bolt

DC Plug

Secondary Video-BNC Cable

7 8

SURFACE MOUNT INSTALLATION INSTRUCTIONS*

Use the camera’s mounting

template or your camera to

mark the holes as required.

Drill holes into the drywall and

insert the drywall mounts into

the holes.

Pull wires through and make

connections.

If you need to keep the wiring within the

camera housing, refer to the diagram

below.

Mount the surface mount

base (junction box) to the

wall.

DC 12V

AC 24V

UTP

RS485

To use the side conduit, remove the

security screw with the supplied

3.0mm Allen key, and unscrew the

conduit plug.

Route wiring behind

the inner posts

(dark gray area).

DC 12V

AC 24V

UTP

RS485

1 2 3

Secure the three (3) assembly

screws.

Adjust the camera’s position

by using the 3-Axis Gimbal.

Tighten the three locking

screws in with the L-Wrench

to secure the dome cover

over the camera.

Snap the camera module onto

the base by aligning the red

and black markings on the

base and the camera module.

6 7 8

FLUSH MOUNT INSTALLATION INSTRUCTIONS*

For a flush mount housing, detach the surface mount base,

which is also known as the junction box, from the flush

mount base.

Use the mounting template to mark the holes for the screws

and a larger hole for the top extruded component of the

flush mount base.

The three assembly screws (ST4X35) fixed to the flush

mount base should be used to mount the camera to the

surface of the wall or ceiling.

ST4X35

Secure the three (3) assembly

screws.

Adjust the camera’s position

by using the 3-Axis Gimbal.

Tighten the three locking

screws in with the L-Wrench

to secure the dome cover

over the camera.

3 4 5

Andere Handbücher für Snapit DWC-V4363D

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Digital Watchdog Sicherheitskamera Handbücher

Digital Watchdog

Digital Watchdog x39 Bedienungsanleitung

Digital Watchdog

Digital Watchdog Star-Light Plus DWC-B6563WTIR Bedienungsanleitung

Digital Watchdog

Digital Watchdog MEGApix PanO DWC-PPVF9Di2TW Bedienungsanleitung

Digital Watchdog

Digital Watchdog Star-Light Plus HD over Coax... Bedienungsanleitung

Digital Watchdog

Digital Watchdog STAR-LIGHT PLUS DWC-V7553WTIR Bedienungsanleitung

Digital Watchdog

Digital Watchdog DWC-D6351D Bedienungsanleitung

Digital Watchdog

Digital Watchdog Star-Light DWC-D4783WD Bedienungsanleitung

Digital Watchdog

Digital Watchdog MEGApix DW-MV82WiA Bedienungsanleitung

Digital Watchdog

Digital Watchdog DWC-VS753WT Bedienungsanleitung

Digital Watchdog

Digital Watchdog MEGApix DWC-MVT4Wi28 Bedienungsanleitung

Digital Watchdog

Digital Watchdog MEGApix DWC-MPA20M Bedienungsanleitung

Digital Watchdog

Digital Watchdog STAR-LIGHT DWC-V4283WTIR Bedienungsanleitung

Digital Watchdog

Digital Watchdog Starlight V3363DH Bedienungsanleitung

Digital Watchdog

Digital Watchdog DWC-MB44iALPR Bedienungsanleitung

Digital Watchdog

Digital Watchdog B2372TIR Bedienungsanleitung

Digital Watchdog

Digital Watchdog MEGApix DWC-MT94WiAT Bedienungsanleitung

Digital Watchdog

Digital Watchdog MegaPix DWC-MVT4WiA Bedienungsanleitung

Digital Watchdog

Digital Watchdog DWC-PB753WTW Bedienungsanleitung

Digital Watchdog

Digital Watchdog STAR-LIGHT 960H DWC-V6553D Bedienungsanleitung

Digital Watchdog

Digital Watchdog Star-Light Plus DWC-B6853WTIR Bedienungsanleitung

Digital Watchdog

Digital Watchdog Star-Light Plus DWC-B6563WTIRW Bedienungsanleitung

Digital Watchdog

Digital Watchdog MEGApix DWC-MTT4WiA Bedienungsanleitung

Digital Watchdog

Digital Watchdog MEGAPIX DWC-MF5Wi4TWDMP Bedienungsanleitung

Digital Watchdog

Digital Watchdog DWC-PZ21M69TW Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung