Directed Electronics Python 533 Bedienungsanleitung

Model 533

Installation Guide

This product is intended for installation by a professional

installer only! Attempts to install this product by a person other than a

trained professional may result in severe damage to a vehicle’s electrical

system and components.

N5303P 2009-07

Bitwriter®, Code Hopping™, Doubleguard®, ESP2™, FailSafe®,

Ghost Switch™, Learn Routine™, Nite-Lite®, Nuisance Prevention®

Circuitry, Revenger®, Silent Mode™, Soft Chirp®, Stinger®,

Valet®, Vehicle Recovery System®, VRS®, and Warn Away® are all

Trademarks or Registered Trademarks of Directed Electronics.

Bitwriters with date code of 6A or older require an IC upgrade (p/n

998M). Some Bitwriters with a date code of 6B do not require the IC

upgrade. Refer to Tech Tip # 1112 for more information.

The Bitwriter® (p/n 998U)

requires chip version 2.7 or

newer to program this unit.

The 3-pin to 4-pin adapter cable is also required.

(included with 998U v 2.6 and above).

Contents

Warning! Safety first .........................................................................................5

What is included...............................................................................................7

Installation points to remember............................................................................8

Virtual tach ..............................................................................................8

D2D........................................................................................................8

Before beginning the installation.................................................................9

After the installation ..................................................................................9

Component locations and finding wires ............................................................10

Valet/program switch..............................................................................10

Status LED..............................................................................................11

Making your wiring connections .......................................................................12

Primary harness (H1), 12-pin connector.....................................................13

Auxiliary harness (H2), 6-pin connector.....................................................13

Door lock harness, 3-pin connector ...........................................................13

Remote start ribbon harness .....................................................................14

Heavy gauge relay satellite .....................................................................14

Relay satellite 4-pin connector ..................................................................14

Remote start harness, (H3) 5-pin connector ................................................15

AUX 4/Horn (H4), 2-pin connector ...........................................................15

Wire connection guides...................................................................................15

Primary harness (H1), 12-pin connector.....................................................15

Auxiliary harness (H2), 6-pin connector.....................................................21

Heavy Gauge relay satellite .....................................................................24

Relay satellite 4-pin connector .................................................................26

Remote start, (H3) secondary harness .......................................................26

AUX 4, Horn, (H4) 2-pin connector...........................................................28

Neutral safety switch interface ..........................................................................29

Testing the neutral safety switch ................................................................29

Plug-in LED and valet/program switch................................................................30

D2D programmer interface - 4-pin red plug ........................................................30

Shock sensor harness, 4-pin connector...............................................................31

Tachometer settings .........................................................................................32

Virtual tach ............................................................................................32

Tach learning .........................................................................................33

Programming jumpers......................................................................................34

Tach threshold On/Off ............................................................................34

Light flash (+) / (-) polarity .......................................................................34

Transmitter/receiver Learn Routine™..................................................................35

Transmitter configurations.................................................................................38

Standard configuration............................................................................38

Multi-level security arming ................................................................................39

System features learn routine ............................................................................40

Feature menus ................................................................................................42

Menu 1 - Basic ......................................................................................42

Menu 2 - Advanced ...............................................................................43

Menu 3 - Remote start ............................................................................44

Feature descriptions.........................................................................................45

Menu 1 - Basic ......................................................................................45

Menu 2 - Advanced ................................................................................48

Menu 3 - Remote start ............................................................................51

Additional features .........................................................................................53

Table of zones ................................................................................................54

Long term event history ....................................................................................55

Shutdown diagnostics......................................................................................56

Safety check...................................................................................................57

Troubleshooting ..............................................................................................58

Alarm....................................................................................................58

Remote start ..........................................................................................59

Wiring quick reference guide ...........................................................................61

Relay satellite wiring quick reference guide ........................................................62

Satmode,

bank selector

AUDIO

PWR

REWFF

PLAY/PROG NR

3456

DISC- DISC+

11:53

XM1-1 CH-001

VOL

SCAN SOUND

AM/FM

CD/AUX

SAT

RADIO

SEEK

SKIP

RPT

DISP -

MODE

A.SEL

RDM

TUNE

AUTO

OFF

DUAL

A/C MODE

Channel control

Category

Control

001 014 018

040 065 115

Toggles between

channel and

category modes

Bank and

present

indicator

Upper display

text mode

selector

Sat mode

and bank

selector

Preset 1-6.

Press until

beepto save

to a preset.

Channeland text

Indicator fields

Toggles

Scan mode

Tune mode

indicator

ANTENNA

SC OUTPUT

Sirius-Ready, SAT Radio Ready or select OEM headunits with optional Honda Bus Compatible Translator

Headunit bus cableSiriusConnect Cable

HON-SC1

Honda Bus

Compatible

Translator

Warning! Safety ﬁrst

The following safety warnings must be observed at all times:

Due to the complexity of this system, installation of this product must only be•

performed by an authorized Directed Electronics dealer.

When properly installed, this system can start the vehicle via a command•

signal from the remote control. Therefore, never operate the system in an

area that does not have adequate ventilation.

The following precautions are the sole responsibility of the user; however, autho-

rized Directed Electronics dealers should:

Never use a test light or logic probe when installing this unit. Always•

use a multimeter.

Never operate the system in an enclosed or partially enclosed area without•

ventilation (such as a garage).

When parking in an enclosed or partially enclosed area or when having•

the vehicle serviced, the remote start system must be disabled using the

installed toggle switch. It is the user’s sole responsibility to properly handle

and keep out of reach from children all remote controls to assure that the

system does not unintentionally remote start the vehicle.

USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT

THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING

FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY EN-

CLOSEDVEHICLESTORAGEAREAMUST REMAINCLOSEDAT ALL TIMES.

Use of this product in a manner contrary to its intended mode of operation may

result in property damage, personal injury, or death. Except when performing

the Safety Check outlined in this installation guide, (1) Never remotely start the

vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the

keys in the ignition. The user will be responsible for having the neutral safety fea-

ture of the vehicle periodically checked, wherein the vehicle must not remotely

start while the car is in gear. This testing should be performed by an authorized

Directed Electronics dealer in accordance with the Safety Check outlined in

this product installation guide. If the vehicle starts in gear, cease remote start

operation immediately and consult with the user to ﬁx the problem immediately.

After the remote start module has been installed, test the remote start module

in accordance with the Safety Check outlined in this installation guide. If the

vehicle starts when performing the Neutral Safety Shutdown Circuit test, the

remote start unit has not been properly installed. The remote start module must

be removed or properly reinstalled so that the vehicle does not start in gear. All

installations must be performed by an authorized Directed Electronics dealer.

OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN

GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERAT-

ING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RE-

SULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE

THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED RE-

MOTE START MODULE. DIRECTED ELECTRONICS, INC. WILL NOT BE HELD

RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.

What is included

A control module•

A transceiver/antenna•

One 5-button 2-way LCD transmitter (P/N 477P)•

One 4-button 1-way transmitter (P/N 474P)•

A Stinger™ DoubleGuard® two-stage shock sensor•

A Revenger™ Soft Chirp™ six-tone programmable siren•

A status LED indicator light•

A push-button Valet® switch•

A shut-down toggle switch•

513

533

Installation points to remember

This product is designed for fuel-injected, automatic transmission vehicles only.

Installing it in a standard transmission vehicle is dangerous and is contrary to

its intended use.

➤ Virtual tach

Virtual Tach is the default RPM-sensing method for the new hybrid keyless entry

/remote start systems. Virtual Tach gives the installer the performance of a hard

wired tach wire, with the convenience of voltage sensing. It is far superior to

any voltage-sense feature you’ve tried before. This feature monitors the cranking

voltage of the vehicle using a very fast micro controller and an analog-to-digital

converter. The microprocessor “saves” the base voltage as a reference. When

Virtual Tach “sees” the slightest uptick in voltage, indicating that the alternator is

charging the battery, the starter motor shuts off instantly.

➤ D2D

The system has the ability to interface with an Xpresskit module through the D2D

port. The advantage to using a D2D interface is that there is less wiring involved

in the installation. Check the Xpresskit module installation guide to determine

which wires are not needed, and which options are available. For more infor-

mation visit www.xpresskit.com.

➤ Before beginning the installation

Please read this entire installation guide before beginning the installation.•

The installation of this remote start system requires interfacing with many of

the vehicle’s systems. Many new vehicles use low-voltage or multiplexed

systems that can be damaged by low resistance testing devices, such as

test lights and logic probes (computer safe test lights). Test all circuits with a

high quality digital multi-meter before making connections.

Do not disconnect the battery if the vehicle has an anti-theft-coded radio.•

If equipped with an air bag, avoid disconnecting the battery if possible.

Many airbag systems display a diagnostic code through the warning lights

after the lights lose power. Disconnecting the battery causes the anti-theft

code to be erased, which can then require a trip to the dealer.

If using an external LED or Valet Switch, check with the customer about•

where to locate the switch.

To avoid accidental battery drainage; turn off the interior lights or remove•

the dome light fuse.

Roll down a window to avoid being locked out of the car.•

➤ After the installation

Test all functions. The Using Your System section of the Owner’s Guide is•

very helpful when testing.

When testing, don’t forget that this system is equipped with Nuisance•

Prevention® Circuitry (NPC). NPC can bypass trigger zones, making

them appear to stop working. See the Nuisance Prevention® Circuitry

section of the Owner's Guide.

Review and complete the Safety Check section of this guide prior to the•

vehicle reassembly.

Component locations and ﬁnding wires

For detailed information on where to locate components, and how to ﬁnd the

wires you need, please refer to the Direct Tech web site at

www.directechs.com.

➤Valet/program switch

IMPORTANT! When the vehicle is delivered, please show the user where this

switch is located and how to disarm the system with it.

Ensure that the location you pick for the switch has sufﬁcient clearance to the

rear. The switch should be well hidden. It should be placed so passengers or

stored items (such as in a glove box or center console) cannot accidentally hit it.

The switch ﬁts into a 9/32-inch hole.

This system has Remote Valet. The user can enter and exit Valet Mode without

having to reach the Valet/Program switch. This feature was introduced so that

switch location was less critical in day-to-day use. As long as the Valet/Program

switch can be reached to disarm without a transmitter, easy access is not im-

portant.

Inhaltsverzeichnis

Andere Directed Electronics Autoalarmanlage Handbücher

Directed Electronics

Directed Electronics SmartStart 5000-series Bedienungsanleitung

Directed Electronics

Directed Electronics 625 Bedienungsanleitung

Directed Electronics

Directed Electronics 446 Series Bedienungsanleitung

Directed Electronics

Directed Electronics 6000 Bedienungsanleitung

Directed Electronics

Directed Electronics 2102T Bedienungsanleitung

Directed Electronics

Directed Electronics Vehicle Security System 3901V Bedienungsanleitung

Directed Electronics

Directed Electronics PYTHON 333 Bedienungsanleitung

Directed Electronics

Directed Electronics 700 ESP Bedienungsanleitung

Directed Electronics

Directed Electronics 737T Bedienungsanleitung

Directed Electronics

Directed Electronics 435 Bedienungsanleitung

Directed Electronics

Directed Electronics Hornet 563T Bedienungsanleitung

Directed Electronics

Directed Electronics Automate 640M Bedienungsanleitung

Directed Electronics

Directed Electronics Responder 460 Bedienungsanleitung

Directed Electronics

Directed Electronics Hornet 742T Bedienungsanleitung

Directed Electronics

Directed Electronics Viper 350HV Bedienungsanleitung

Directed Electronics

Directed Electronics 429 Series Bedienungsanleitung

Directed Electronics

Directed Electronics 555X Bedienungsanleitung

Directed Electronics

Directed Electronics 560XV Bedienungsanleitung

Directed Electronics

Directed Electronics VIPER 1000 Bedienungsanleitung

Directed Electronics

Directed Electronics AM1 Bedienungsanleitung

Directed Electronics

Directed Electronics Viper 211HV Bedienungsanleitung

Directed Electronics

Directed Electronics 100 ESP Bedienungsanleitung

Directed Electronics

Directed Electronics Hornet 563T Bedienungsanleitung

Directed Electronics

Directed Electronics Security System and Convenience 125xv Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Ultra Start

Ultra Start 450 SERIES Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Excalibur

Excalibur AL-1860-EDPB Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung