Directed DS3+ Bedienungsanleitung
Designed by Installers for Installers
INSTALLATION GUIDE
DS3+ / DS4+
2019 Nissan Qashqai (Smart Key). 933.NISS06 3.23.195.3
© 2021 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle’s
electrical system and components.
Introduction 3
Vehicle function compatibilities 3
Pre-installation and application warnings 4
Installation 4
Wiring diagram with T-Harness (THNIN5) 4
Wiring diagram 6
Locating components in the vehicle 7
Vehicle connections 8
Connecting the module 13
Important! 13
8556T Temperature Sensor 13
8504D Combo Sensor 13
RF Systems 14
When used in conjunction with SmartStart 14
D2D port configuration 14
Manual Transmission 15
Module programming 16
(For security-only programming, see next section.) 16
Module programming for security-only installations 17
LED diagnostics and troubleshooting 18
Soft reset 20
Hard reset 20
Learning the Tach (not needed with Virtual Tach) 21
Initializing Virtual Tach (not needed with hardwired or data tach applications) 21
Limited lifetime consumer warranty 22
Quick reference guide 23
Contents
3933.NISS06 3.23.195.3 2019 Nissan Qashqai (Smart Key)
©2021 VOXX•DEI LLC. All rights reserved.
Introduction
DS3+ is a complete solution for remote start, security (when security features are enabled) and bypass. This guide provides
information on the installation of the module as a digital solution. Please refer to www.directechs.com for more information about
which configuration is best for your application.
Warning! This module can be configured using the web tool located at www.directechs.com. The DS3/DS3+ module is not
equipped with Bluetooth, therefore the blue LED will not flash during module programming or when performing a soft or hard reset.
DS4+ is a complete solution for remote start, security (when security features are enabled), bypass, and features
built in Bluetooth 4.0 allowing you to configure and control your system. This guide provides information on the
installation of the module as a digital solution. Please refer to the DirectLink application or www.directechs.com
for more information about which configuration is best for your application.
Warning! This module is designed to be configured using the DirectLink application for mobile devices,
however it can also be configured using the web tool located at www.directechs.com. To download the DirectLink mobile
application, please visit the Google Play or Apple store.
Vehicle function compatibilities
This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.
Note: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart.
Parking Lights Control
Arm Factory Security
Disarm Factory Security
Door Lock Control
Door Unlock
Trunk / Hatch Release
Control of aftermarket alarm with OEM remote
* Fuel Level
* Odometer
Immobilizer Bypass-Data No Key Req'd
3x LOCK START (Start control using OEM Remote)
3x LOCK STOP (Stop control using OEM Remote)
Accessory Activation
Ignition Activation
Remote Start Takeover
SmartStart
Start (Crank) Activation
Tach / RPM Output
Entry Monitoring ALL Door Pins
Entry Monitoring Hood Pin
Entry Monitoring Trunk/Hatch Pin
Factory Alarm Trigger Monitoring
Brake Status (foot brake)
Door Locks Status
E-Brake Status
Ignition Status
4933.NISS06 3.23.195.3 2019 Nissan Qashqai (Smart Key)
©2021 VOXX•DEI LLC. All rights reserved.
Pre-installation and application warnings
Firmware notes: This section highlights important information for this specific firmware and will assist in pricing accordingly,
as well as bringing awareness to any operational or vehicle limitations.
T-Harness
compatible THNIN5 Keys required for
programming 1Keys required for
operation 0
The optional Plug & Play THNIN5 T-Harness is sold separately.
All T-Harness wires NOT listed in the diagram are NOT required for the installation. Loose wires such as Siren Output and Hood Input
may need to be pulled from the tapped section of the T-harness. Refer to the "wiring diagram with T-Harness" for more information on
connections and installation instructions.
All connectors are displayed from the wire side (unless specified otherwise).
It is important to check that the fuses are positioned correctly in the module. Proper fuse positioning is displayed on each wiring diagram.
Refer to the "Vehicle connections" following the installation diagram.
General notes: This section highlights important information for this specific firmware.
[1] The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin or if NOT supported
in data.
[2] The siren is ONLY required when enabling the security features during module flashing.
[3] The vehicle MUST be disarmed for the power tailgate to operate.
[4] For security-only installations, refer to the "Locating components in the vehicle" section for optional starter disable connection.
5933.NISS06 3.23.195.3 2019 Nissan Qashqai (Smart Key)
©2021 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
Hood Pin
Siren
(+) Siren Output: Brown/Red
THNIN5
(Optional T-Harness)
(-) Hood Pin Input: Gray
Wiring diagram with T-Harness (THNIN5)
BCM
E29
M19
M18
B16
BCM Connector M18
(grey conn. at BCM)
BCM Connector M19
(black conn. at BCM) BCM Connector B16 (green conn. at BCM)
BCM Connector E29
(black conn. at BCM)
M10
BCM Connector M10
(brown conn. at BCM)
(+) Starter Disable Output: Violet/Black
Refer to the
Optional starter
disable
connection
section for relay
and connection
details.
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
22 812
4 2442
Slide to open
A module can also be used for
this installation.
IMPORTANT:
Position the
fuses correctly!
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
5
30
20
20
15
15
8-pin White connector
22-pin White connector
12-pin Black connector
Do NOT cut the
Lt. Green/Black
loop.
6933.NISS06 3.23.195.3 2019 Nissan Qashqai (Smart Key)
©2021 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
Wiring diagram
(-) Hazards Output: White: 5 & 11
(-) Ground: Black: 10
(+) 12V Input: Red: 6 & 12
40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21
20 19 18 17 16 15 14 13 12
11 10
98 7 6543 2 1
BCM Connector M18
(grey conn. at BCM)
(-) Accessory 2:
Lavender/Pink, pin 25
(-) Ignition:
Lavender/L.t Green, pin 27
(-) Accessory 1:
Lavender/Blue, pin 28
(-) Hazards:
Lavender/Yellow, pin 11
HS CAN Low: Tan: 1
HS CAN High: Tan/Black: 2
(-) PTS:
Red,
pin 9
(-) Arm:
Brown,
pin 12
(-) Disarm:
Pink, pin 13
(+) 12V:
Blue, pin 1
BCM Connector M19
(black conn. at BCM)
White conn.
(back of dash
fuse box)
40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21
20 19 18 17 16 15 14
13 12
11 10 8
9
7 6 5 4 3 21
1
(-) Starter:
Blue, pin 19
18 1524 20 16 1322 1921 17 1423
63
12 841
10 7
9
5
2
11
BCM Connector E29
(black conn. at BCM)
HS CAN Low: Pink
or Lavender/Pink,pin 40
HS CAN High: Blue
or Lavender/Blue, pin 20
123456789
10111213141516
17
1819
20
212223242526272829303132
33
343536373839
40
BCM Connector B16 (green conn. at BCM)
Siren
Hood Pin
(+) Siren Output: Brown/Red: 11
(-) Ignition Output: Brown/White: 6
(-) Accessory Output: Brown/Black: 5
(-) Disarm Output: Dk. Blue/Black: 9
(-) Push-to-Start Output: Lt.Green/Black: 1
(-) Accessory 2 Output: Blue/White: 2
(-) Starter Output: Lt. Blue/Black: 10
(-) Hood Input: Gray: 21
(-) Lock:
Gray, pin 10
(-) Arm Output: Orange/Black: 7
(-) Lock Output: Yellow/Black: 8
BCM
E29
M19
M18
B16
M10
(+) Starter Disable Output: Violet/Black: 8
Refer to the
Optional starter
disable
connection
section for relay
and connection
details.
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
22 812
4 2442
Slide to open
A module can also be used for
this installation.
IMPORTANT:
Position the
fuses correctly!
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
5
30
20
20
15
15
7933.NISS06 3.23.195.3 2019 Nissan Qashqai (Smart Key)
©2021 VOXX•DEI LLC. All rights reserved.
Locating components in the vehicle
Cut
(-) Starter: Green
or Blue, pin 19
18 1524 20 16 1322 1921 17 1423
63
12 841
10 7
9
5
2
11
BCM Connector E29
(Black conn. at BCM)
Optional starter disable connection
When using an external relay, use a 1N4002 diode or larger.
22 812
4 2442
(+) Starter Disable Output: Violet/Black: 8
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
86 85
30
87a
87
40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21
20 19 18 17 16 15 14 13 12 11 10 9876543 2 1
BCM Connector M18
(Grey conn. at BCM)
(-) Ignition: Yellow or
Lavender/L.t Green, pin 27
1A Diode (1N4002+)
Important: When flashing your module for Security Only, the Ground When Armed (GWA)
function is pre-configured. When flashing your module for Remote Start & Security, you must
manually assign the designated output to Anti Grind (AG) Starter Kill.
(Applicable to CORE 194+.)
8933.NISS06 3.23.195.3 2019 Nissan Qashqai (Smart Key)
©2021 VOXX•DEI LLC. All rights reserved.
Vehicle connections
The connection information listed below is specific to the 2019 Nissan Qashqai (Smart Key). Refer to “Pre-installation and application warnings” for a list of important notes.
Data harness, 8-pin white connector (H1)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H1/1 Tan (Data) HS CAN Low BCM under driver dash, green 40 pin plug, pin 40
BCM under driver dash, green 40 pin plug, pin 40
Not Applicable
Data
Data
Lavender/Pink
Lavender/Pink
Mandatory
H1/2 Tan HS CAN Low 1 BCM under driver dash, green 40 pin plug, pin 40 Data Lavender/Pink Mandatory
H1/3 Tan/Black HS CAN High 1 BCM under driver dash, green 40 pin plug, pin 20 Data Lavender/Blue Mandatory
H1/4 Tan/Black (Data) HS CAN High BCM under driver dash, green 40 pin plug, pin 20
BCM under driver dash, green 40 pin plug, pin 20
Not Applicable
Data
Data
Lavender/Blue
Lavender/Blue
Mandatory
H1/5 Orange/Brown No Connection No Connection
H1/6 Orange/Brown HS CAN Low 2 No Connection
H1/7 Orange/Green HS CAN High 2 No Connection
H1/8 Orange/Green No Connection No Connection
H1/9 Lt. Green No Connection No Connection
H1/10 Lt. Green No Connection No Connection
H1/11 Violet/Brown No Connection No Connection
H1/12 Violet/Brown No Connection No Connection
H1/13 Orange/Black (-) Arm Output BCM under driver dash, black 40 pin plug, pin 12 - Brown (key lock) Mandatory
H1/14 Orange/Black No Connection No Connection
H1/15 Yellow/Black No Connection No Connection
H1/16 Yellow/Black (-) Lock Output BCM under driver dash, gray 40 pin plug, pin 10 - Gray Mandatory
Analog input/output harness, 22-pin white connector (H2)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H2/1 Lt. Green/Black (-) PTS Output BCM under driver dash, black 40 pin plug, pin 9 - Red Remote Start
Only
H2/2 Lt. Green/Black (-) Factory Alarm Arm (FAA) Output No Connection
H2/3 Blue/White (-) Ground When Running (Status) Output No Connection
H2/4 Blue/White (-) Accessory 2 Output BCM under driver dash, gray 40 pin plug, pin 25 - Lavender/Pink Remote Start
Only
H2/5 Dk. Green/Black (-) Lock Output No Connection
H2/6 Dk. Green/Black (-) Lock Output No Connection
H2/7 Red/White (-) Trunk Output No Connection
H2/8 Red/White (-) Trunk Release Output No Connection
H2/9 Brown/Black (-) Accessory Output BCM under driver dash, gray 40 pin plug, pin 28 - Lavender/Blue Remote Start
Only
H2/10 Brown/Black (-) Horn Output No Connection
9933.NISS06 3.23.195.3 2019 Nissan Qashqai (Smart Key)
©2021 VOXX•DEI LLC. All rights reserved.
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H2/11 Brown/White N/A No Connection
H2/12 Brown/White (-) Ignition Output BCM under driver dash, gray 40 pin plug, pin 27 - Lavender/Lt. Green Remote Start
Only
H2/13 White (+) AUX 1 Output No Connection
H2/14 White (+) AUX 1 Output No Connection
H2/15 Violet/Black (+) AUX 4 Output No Connection
H2/16 Violet/Black (+) Starter Disable Output [4] Starter:
BCM under driver dash, black 24 pin plug, pin 19
Ignition:
BCM under driver dash, gray 40 pin plug, pin 27
Must use a relay.
Must use a 1N4002 diode or larger.
-
-
Blue
Lavender/Lt. Green
Security Only
H2/17 Dk. Blue/Black (-) Disarm Output BCM under driver dash, black 40 pin plug, pin 13 Doubl
e -
Pink (key unlock) Mandatory
H2/18 Dk. Blue/Black (-) Unlock Output No Connection
H2/19 Lt. Blue/Black (-) Factory Alarm Disarm (FAD) Output No Connection
H2/20 Lt. Blue/Black (-) Starter Output BCM under driver dash, black 24 pin plug, pin 19 - Blue Remote Start
Only
H2/21 Brown/Red (+) Siren Output [2] Security Only
H2/22 Brown/Red (+) Siren Output Mandatory
H2/23 Pink (+) Ignition Sense Input No Connection
H2/24 Pink (+) Ignition Sense Input No Connection
H2/25 Violet (+) Door Trigger Input No Connection
H2/26 Violet (+) Door Input No Connection
H2/27 Brown (+) Brake Input No Connection
H2/28 Brown (+) Brake Input No Connection
H2/29 White/Blue (-) Activation Input No Connection
H2/30 White/Blue (-) Activation Input No Connection
H2/31 Red/Blue (-) Trigger Input No Connection
H2/32 Red/Blue No Connection No Connection
H2/33 Black/White (-) E-Brake Input No Connection
H2/34 Black/White (-) E-Brake Input (manual transmission) No Connection
H2/35 Orange/Black (+) Valet Switch Input No Connection
H2/36 Orange/Black (+) Instant Alarm Input No Connection
H2/37 Blue (-) Trunk Trigger Input No Connection
H2/38 Blue (-) Trunk Input No Connection
H2/39 Green (-) Door Input No Connection
H2/40 Green (-) Door Trigger Input No Connection
H2/41 Gray (-) Hood Switch Input [1]
H2/42 Gray (-) Hood Input Mandatory
H2/43 Violet/White (AC) Tach Input No Connection
10 933.NISS06 3.23.195.3 2019 Nissan Qashqai (Smart Key)
©2021 VOXX•DEI LLC. All rights reserved.
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H2/44 Violet/White (AC) Tach Input No Connection
Main harness, 12-pin black connector (H3)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H3/1 Blue/White Relay N.C. No Connection No Connection
H3/2 Blue/White Relay 1 N.C. – No Connection No Connection
H3/3 Blue/Red Relay 1 N.O. – No Connection No Connection
H3/4 Blue/Red Relay N.O. No Connection No Connection
H3/5 Blue Relay COM No Connection No Connection
H3/6 Blue Relay 1 COM – No Connection No Connection
H3/7 White/Brown Relay 3 N.C. – No Connection No Connection
H3/8 White/Brown Relay N.C. No Connection No Connection
H3/9 White Relay COM. (-) Hazards Output BCM under driver dash, gray 40 pin plug, pin 11 - Lavender/Yellow Mandatory
H3/10 White Relay 3 COM – No Connection No Connection
H3/11 Red (+) 12 Volt (Battery) Dash Fuse Box, rear, white 1 pin plug, pin 1 + Blue (30A) Mandatory
H3/12 Red (+) 12 Volt Input Dash Fuse Box, rear, white 1 pin plug, pin 1
Dash Fuse Box, rear, white 1 pin plug, pin 1
Not Applicable
+
+
Blue (30A)
Blue (30A)
Mandatory
H3/13 Lt. Green/Red Relay N.O. No Connection No Connection
H3/14 Lt. Green/Red Relay 2 N.O. – No Connection No Connection
H3/15 Lt. Green Relay 2 COM – No Connection No Connection
H3/16 Lt. Green Relay COM No Connection No Connection
H3/17 Lt. Green/White Relay N.C. No Connection No Connection
H3/18 Lt. Green/White Relay 2 N.C. – No Connection No Connection
H3/19 Black (-) Ground (chassis ground) Mandatory
H3/20 Black (-) Ground Not Applicable (chassis ground)
(chassis ground)
Mandatory
H3/21 White Relay COM. (-) Hazards Output BCM under driver dash, gray 40 pin plug, pin 11 - Lavender/Yellow Mandatory
H3/22 White Relay 3 COM – No Connection No Connection
H3/23 Red (+) 12 Volt (Battery) Dash Fuse Box, rear, white 1 pin plug, pin 1 + Blue (30A) Mandatory
H3/24 Red (+) 12 Volt Input Dash Fuse Box, rear, white 1 pin plug, pin 1
Dash Fuse Box, rear, white 1 pin plug, pin 1
Not Applicable
+
+
Blue (30A)
Blue (30A)
Mandatory
Relay harness, 10-pin white connector (H4)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H4/1 N/A No Connection No Connection
H4/2 N/A No Connection No Connection
Andere Handbücher für DS3+
19
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Directed Autozubehör Handbücher
Directed
Directed GM11 Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
Directed
Directed XPRESSKIT optimax Series Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
Directed
Directed DIRECTECHS HONDA4 Bedienungsanleitung
Directed
Directed DS3+ Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
Directed
Directed DIRECTWIRE DIRECTECHS 933.TL14 Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
Directed
Directed FORD5 Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
Directed
Directed DS3+ Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
