Directed VOXX DEI 933.VW14 v2.11.198.12 Bedienungsanleitung

933.VW14

v2.11.198.12

2018 Volkswagen Tiguan (Smart Key)

THVWN2 Compatible

(Sold Separately)

Functions compatible with the 2018 Volkswagen Tiguan (Smart Key)

*Telematics features: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart Pro.

* Odometer

3x LOCK START (Start control using OEM Remote)

3x LOCK STOP (Stop control using OEM Remote)

Arm Factory Security

Brake Status (foot brake)

Disarm Factory Security

Door Lock Control

Door Locks Status

Door Unlock

Driver Priority Unlock

E-Brake Status

Entry Monitoring ALL Door Pins

Entry Monitoring Driver Door Pin

Entry Monitoring Hood Pin

Entry Monitoring Trunk/Hatch Pin

Factory Alarm Trigger Monitoring

FOB Control

Fuel level/EV battery level

Ignition Status

RAP Shut Down (Retained ACC Power)

Remote Start Takeover

SmartStart

Tach / RPM Output

Trunk / Hatch Release

Universal RF Bypass- Key Req'd

Introduction 3

Pre-installation and application warnings 4

Installation 5

Wiring diagram with T-Harness (THVWN2) 5

Wiring diagram 6

Key Wrap with T-Harness (THVWN2) 7

Immobilizer interface 8

Locating components in the vehicle 10

Vehicle connections 11

Module programming 14

For Security-Only programming, see next section. 14

Module programming for security-only installations 15

Pairing remotes 16

Connecting the module 16

8556T Temperature Sensor 16

8504D Combo Sensor 16

RF Systems 16

When used in conjunction with SmartStart 17

D2D port configuration 17

Manual transmission 18

LED diagnostics and troubleshooting 19

Soft reset 21

Hard reset 21

Tach learning procedure (not needed with Virtual Tach) 22

Initializing Virtual Tach (not needed with hardwired or data tach applications) 22

Limited lifetime consumer warranty 23

Quick Reference Guide (customer copy) 24

Contents

3933.VW14 2.11.198.12 2018 Volkswagen Tiguan (Smart Key)

Introduction

This guide provides information on the installation of the DS3/DS3+ and DS4/DS4+ modules as a digital solution. Using these modules in a

digital conﬁguration requires the module to be ﬂashed with vehicle-speciﬁc ﬁrmware. Refer to our website (www.directechs.com) and click

on the DIRECTLINK text in the header for additional information.

DS3/DS3+ and DS4/DS4+ modules provide an all-in-one solution for most modern vehicles, and include remote start, keyless entry, security,

and immobilizer bypass capabilities. T-harnesses may also be used in many applications for easy installation.

The following methods are available to conﬁgure modules:

• Web: www.directechs.com (DS3/DS3+ and DS4/DS4+)

• Desktop application: Directlink DT (DS3/DS3+ and DS4/DS4+)

• Mobile device: Directlink App (DS4/DS4+ only)

When ﬂashing via Directlink DT (desktop app) or via the Web, an XKloader2 will be required.

To conﬁgure via Web or DirectLink DT (desktop app):

1. Disconnect the main module from any (+) 12V power source.

2. Connect the module to your computer using the XKLoader2.

3. Follow the steps in the pop-up window that will be displayed when the module is detected.

Notes:

•Flashing via web is only possible using Internet Explorer on Windows 8, 8.1, and 10.

•This method is not compatible with any other browser (Edge, Chrome, Firefox, etc.).

•When using Windows 11 or newer, Directlink DT is mandatory.

The DS4/DS4+ module is designed to be conﬁgured using the DirectLink application through mobile devices.

To download the DirectLink mobile application, visit the Google Play or Apple store. They can also be

conﬁgured via Web and DirectLink DT. The DS4/DS4+ features are built in Bluetooth® 4.0, allowing you to

conﬁgure and control your system. The DS3/DS3+ module is not equipped with Bluetooth®, therefore is not

compatible with the DirectLink app for mobile devices.

To conﬁgure via DirectLink mobile app (Android/iOS):

1. Follow and complete the wiring diagram(s) related to your installation through the app.

2. When installation is complete, select Conﬁgure DS4/DS4+.

3. Follow the on-screen instructions.

FLASH REQUIRED!

4 White

4933.VW14 2.11.198.12 2018 Volkswagen Tiguan (Smart Key)

Pre-installation and application warnings

START HERE This section highlights important information for this speciﬁc ﬁrmware and will assist in pricing accordingly, as

well as bringing awareness to any operational or vehicle limitations.

Compatibilities and Requirements

T-Harness

compatible THVWN2

AUX

Keys required for

programming 1Keys required

for operation 1

Vehicle Takeover Refer to the Quick Reference Guide section for more details.

Firmware notes

Different input/output conﬁgurations: Version 2.00 and higher use different input/output conﬁgurations and are not compatible

with the wiring instructions of previous versions. Updating an older version to version 2.00 or higher will require wiring modiﬁcations.

Note: Damage to the vehicle may occur if the appropriate wiring modiﬁcations are not done.

Immobilizer bypass: This ﬁrmware does not support immobilizer bypass. One (1) programmed OEM key must be wired into the

vehicle to complete the installation of a remote starter.

Remote Start: To remote start the vehicle, ALL doors must be closed and locked.

Fuses: It is important to check that the fuses are positioned correctly in the module. Proper fuse positioning is displayed on each wiring

diagram.

T-Harness (THVWN2):

•All T-Harness wires not listed in the diagram are not required for the installation. Loose wires such as Siren Output and

Hood Input may need to be pulled from the tapped section of the T-harness. Refer to the "wiring diagram with T-Harness"

for more information on connections and installation instructions.

•The optional Plug & Play THVWN2T-Harness is sold separately.

•The OBDII Diagnostic Connector features will remain the same even when the T-Harness is installed.

•All T-Harness wires not listed in the diagram are not required for the installation.

Unless speciﬁed otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.

Refer to the "Vehicle connections" following the installation diagram.

Footnotes

[1] Hood pin: The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory

hood pin, or if not supported in data

[2] Siren: The siren is only required when enabling the security features during module ﬂashing.

[3] Key Wrap instructions: Refer to the "Immobilizer interface with OEM immobilizer receiver" section.

[4] Security Only: Refer to the "Locating components in the vehicle" section for the optional starter disable.

5933.VW14 2.11.198.12 2018 Volkswagen Tiguan (Smart Key)

Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).

(-) GWA Output: Dk. Blue/Black

Cut the Dk. Blue/Black loop labeled GWA

and extend the wires coming from the

module side.

Extend

wire.

Refer to the Optional starter disable connection

section for relay and connection details.

Wiring diagram with T-Harness (THVWN2)

Steering Column Electronics Module

(black connector at steering column)

With Heated

Steering Wheel

(14-pin connector)

Without Heated

Steering Wheel

(16-pin connector)

HS CAN 2 High:

Orange/Green, pin 6

HS CAN 2 Low:

Orange/Brown, pin 5

HS CAN 2 High:

Orange/Green, pin 4

HS CAN 2 Low:

Orange/Brown, pin 3

14 13 12 11 10 9

4 3 26 5

16 15 14 13 12 11

8 7 6 5

14 3

(+) Brake:

Black/Red, pin 7

Brake Connector

(blue connector at driver’s kick)

15 16 17

These connectors are not used for this installation type.

Security Only

Mandatory Connections

Remote Start Only

Legend:

Remote Start + Security

(+) Brake Output: White

Hood Pin (-) Hood Input: Gray

Siren

(+) Siren Output: Brown/Red

22 812

4 2442

Slide to open

A module can also be used for

this installation.

IMPORTANT:

Position the

fuses correctly!

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3/PK LIGHT(15A) (+)

THVWN2

(optional T-Harness

connector side view)

OBDII

Diagnostic

Connector

Key Wrap

Starter

Disable

Relay

8-pin White Connector

12-pin Black Connector

22-pin White Connector

Headlight Switch

(red conn. at light switch)

PKL

CAN-A

CAN-B

PTS Switch

(black connector at

start/stop button)

PTS-1

KEY

PTS-2

CAN 2 High: Orange/Green

CAN 2 Low: Orange/Brown

6933.VW14 2.11.198.12 2018 Volkswagen Tiguan (Smart Key)

Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).

10 6

PTS Switch

(black connector at start/stop button)

(-) PTS 2:

Violet/Blue, pin 4

(-) PTS 1: Violet, pin 3

4321

Wiring diagram

HS CAN Low: Tan: 1

(+) Brake Output: White: 7

(-) PTS 2 Output: Lt. Blue/Black: 10

HS CAN High: Tan/Black: 2

HS CAN 2 High: Orange/Green: 4

HS CAN 2 Low: Orange/Brown: 3

(-)

PTS 1 Output: Lt. Green/Black: 1

Siren Hood Pin

(-) Hood Input: Gray: 21

(+) Siren Output: Brown/Red: 11

Steering Column Electronics Module

(black connector at steering column)

Diagnostic Connector OBDll

(connector side view)

With Heated

Steering Wheel

(14-pin connector)

Without Heated

Steering Wheel

(16-pin connector)

HS CAN Low:

Orange/Brown, pin 14

(+) 12V:

Red/Blue, pin 16

HS CAN High: Orange/Black

Orange/Red, pin 6

HS CAN 2 High:

Orange/Green, pin 6

HS CAN 2 Low:

Orange/Brown, pin 5

HS CAN 2 High:

Orange/Green, pin 4

HS CAN 2 Low:

Orange/Brown, pin 3

(-) Ground: Brown, pin 4

Parking Light Interrupt (connector side): Blue/White: 1

(+) Parking Light Output: Blue/Red: 2

Parking Light Interrupt (vehicle side): Blue: 3

Key Wrap: Lt. Green: 8

Key Wrap: Lt. Green/Red: 7

Key Wrap: Lt. Green/White: 9

(-) Ground: Black: 10

(+) 12V Input: Red: 6 & 12

(+) Parking Lights:

Gray/Yellow, pin 3

Parking Lights Interrupt:

Red/Blue, pin 8

CUT

Headlight Switch

(red connector at light switch)

14 13 12 11 10 9

4 3 26 5

16 15 14 13 12 11

8 7 6 5

14 3

(+) Brake:

Black/Red, pin 7

Brake Connector

(blue conn. at

driver’s kick)

15 16 17

Refer to the Optional

Starter disable connection

section for relay and

connection details.

(-) GWA Output: Dk. Blue/Black: 9

Security Only

Mandatory Connections

Remote Start Only

Legend:

Remote Start + Security

22 812

4 2442

Slide to open

A module can also be used for

this installation.

IMPORTANT:

Position the

fuses correctly!

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3/PK LIGHT(15A) (+)

7933.VW14 2.11.198.12 2018 Volkswagen Tiguan (Smart Key)

Key Wrap with T-Harness (THVWN2)

Remove battery from

OEM Remote Control

The loop must be

positioned over or

under the key but

not around it.

The loop must be

positioned

between the Lock

button and the

flip key button.

Key Wrap

THVWN2

(main section of T-Harness, connector side view)

4 2442

OEM

Immobilizer

Receiver

Use the T-harness connector labeled Key Wrap.

Starter

Disable

Relay

Key Wrap

PKL

Connect the 2-pin conn.

from the t-harness into

the OEM Immobilizer

Receiver connector.

OEM

Immobilizer

Receiver

Cut

NOT

USED

NOT

USED

Cut and extend the Green wire and connect it

to the connector side of the Immobilizer Receiver.

Cut and extend the Green/White wire and connect

it to the vehicle side of the Immobilizer Receiver.

Cut

Immo.: Pin 1

When possible use valet key for key wrap. If a blade key is used or if the vehicle is equipped with Keyless Entry, the battery must be

removed from OEM key (the OEM remote may differ from the models shown in the illustrations).

Make sure to test and secure the loops before reassembling the vehicle.

8933.VW14 2.11.198.12 2018 Volkswagen Tiguan (Smart Key)

- Make 4-6 loops and place them as close to the front of key port (OEM Immobilizer Receiver) as possible.

4-6 loops

COM Relay 2: Lt. Green: 8

N.O. Relay 2: Lt. Green/Red: 7

OEM

Immobilizer

Receiver

4 2442

22 810 12

Method 1: Immobilizer interface with OEM immobilizer receiver

OEM

Immobilizer

Receiver

N/A: Green, pin 6

Black/White - NOT USED

Black/Red

Black

N/A: Violet, pin 5

N/A: Pink, pin 3

(-) GWR: Blue, pin 2

(+)12V : Red, pin 1 (+)12V

(-) Ground: Black, pin 4

556UXL is sold SEPARATELY.

Method 2: Immobilizer interface using 556UXL

IMPORTANT!: Not all OEM remotes can be inserted in 556UXL because of their size.

Make sure the key will fit, otherwise it is recommended to use a different method.

COM Relay 2: Lt. Green: 8

N.O. Relay 2: Lt. Green/Red: 7

4 2442

22 810 12

Note: The discontinued 556U or 556UW can

still be used for the installation.

Move 556UXL loop as close to the

front of ignition cylinder (OEM

Immobilizer Receiver) as possible.

Test and secure mounted loop

before reassembling the vehicle.

Immobilizer interface

4-6 loops

Remove battery from

OEM Remote Control

The loop must be

positioned over or

under the key but

not around it.

Make 4-6 loops

and place them

around the front

of the plastic body

of the vehicle’s

coded key.

The OEM immobilizer

receiver is located on the

underside of the steering

column, where the ignition

switch would normally be.

When possible use valet key for key wrap. If a blade key is used or if the vehicle is equipped with Keyless Entry, the battery must be

removed from OEM key (the OEM remote may differ from the models shown in the illustrations).

Make sure to test and secure the loops before reassembling the vehicle.

4-6 loops

9933.VW14 2.11.198.12 2018 Volkswagen Tiguan (Smart Key)

Method 3: Key wrap using OEM Immobilizer Ring

N.C. Relay 2: Lt. Green/White: 9

OEM

Immobilizer

Ring

Immobilizer

ECU

COM Relay 2: Lt. Green: 8

N.O. Relay 2: Lt. Green/Red: 7

4-6 loops

Remove battery from

OEM Remote Control

The loop must be

positioned over or

under the key but

not around it.

Make 4-6 loops

and place them

around the front

of the plastic body

of the vehicle’s

coded key.

4 2442

22 810 12

4-6 loops

10 933.VW14 2.11.198.12 2018 Volkswagen Tiguan (Smart Key)

Locating components in the vehicle

Optional starter disable connection

When using an external relay, use a 1N4002 diode or larger.

22 812

4 2442

Security Only

Mandatory Connections

Remote Start Only

Legend:

Remote Start + Security

(-) Ground When Armed (GWA) Output: Blue/White: 2

86 85

87a

Cut

Starter (conn. side)

Starter (veh. side)

(+) Ignition

Refer to the

Vehicle connections

section for wire and

connector details.

1A diode [1N4002+ ]

Important: When ﬂashing your module for Security Only, the Ground When Armed (GWA)

function is pre-conﬁgured. When ﬂashing your module for Remote Start & Security, you must

manually assign the designated output to Anti Grind (AG) Starter Kill.

(Applicable to CORE 194+.)

Inhaltsverzeichnis

Andere Directed Autozubehör Handbücher

Directed

Directed DS3+ Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed GM10 Gebrauchs- und Pflegehandbuch

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed VOXX DEI 403.VW14 v2.11 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed FORD12 Bedienungsanleitung

Directed

Directed Xpresskit DBALL2 Bedienungsanleitung

Directed

Directed XPRESSKIT solex DLCH-CHDL6+ Bedienungsanleitung

Directed

Directed DS4+ Bedienungsanleitung

Directed

Directed Directechs DS3 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed 933.NISS3HT Bedienungsanleitung

Directed

Directed DS4+ Bedienungsanleitung

Directed

Directed 933.MIT3 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed DS3+ Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed DS3+ Bedienungsanleitung

Directed

Directed FORD5 Bedienungsanleitung

Directed

Directed DS4+ Bedienungsanleitung

Directed

Directed DS3+ Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung