Dji E800 Bedienungsanleitung

DJI E800

Multirotor Propulsion System

V1.0 2015.01

User Manual

DJI E800 Multirotor Propulsion System

Disclaimer

Thank you for purchasing the E800 (hereinafter referred to as “product”). Read this disclaimer carefully

before using this product. By using this product, you hereby agree to this disclaimer and signify that

you have read it fully. Please strictly install and use this product in accordance with the manual. DJI

assumes no liability for damage(s) or injuries incurred directly or indirectly from using, installing or

retting this product improperly, including but not limited to using accessories not designated. Ensure

your ESC rmware matches the motor you will attach it to. Otherwise, you are responsible for all

consequences caused by your own conduct.

This device complies with part 15 of the FCC Rules.

DJI is the registered trademark of SZ DJI Technology Co., Ltd. (abbreviated as “DJI”). Names of

product, brand, etc., appearing in this manual are trademarks or registered trademarks of their

respective owner companies. This product and manual are copyrighted by DJI with all rights

reserved. No part of this product or manual shall be reproduced in any form without the prior written

consent or authorization of DJI.

This disclaimer is made in various language versions; in the event of divergence among different

versions, English version shall prevail.

Cautions

When powered on, the motors and propellers will rotate very quickly and may cause serious

damage and injury. Therefore, please always be aware for your safety.

1. Always y your aircraft a safe distance away from people, animals, high-voltage lines and other

obstacles.

2. Do not get close to or touch the motors or propellers when powered on, as this may cause serious

injury.

3. Make sure there is no short circuit or open circuit.

4. Check that the propellers and the motors are installed correctly and rmly before ight.

5. Check whether all parts of your aircraft are in good condition before ight. Do not y with worn or

broken parts.

6. Use compatible DJI parts.

Legend

Important Hints and Tips Reference

DJI Support Website:

www.dji.com/support

If you have any problems you cannot solve, please contact your local dealer or DJI customer service.

DJI E800 Multirotor Propulsion System

About

The E800 Multirotor Propulsion System is a tuned propulsion system customized for multi-rotor

aircraft weighing 3 to 5 kg. It is efcient, reliable and minimizes vibrations. A revolutionary Electronic

Speed Control (ESC) with a sinusoidal drive replaces the traditional square wave drive, and along

with the new AC permanent magnet synchronous motor, the whole propulsion system is brought

into an era of higher efficiency while providing a steady torque output. The integrated sensors

and patented algorithms give the whole system a high level of intelligence and redundancy, and

advanced features include closed loop torque control, active braking and energy optimization, real-

time system health diagnosis, distinct functional redundancy for the communication link, and more.

Furthermore, the ESC’s rmware can be upgraded by users, enabling you to enjoy the continual

development of the system. The E800 uses new quick-release propellers, which are designed

to prevent propellers from ying off during active braking. Together with the energy optimization

function of the new ESCs, propulsion performance is more efcient than ever before.

1. In the Box

Standard Package

The E800 is available in two different package congurations. The descriptions below correspond

with the Quad-rotor and Hexa-rotor packages, respectively. Please ensure that you have the correct

quantities of each part before beginning the installation process or using the product.

E.g. “1345 Quick-Release Propeller Pair ×4 or ×5” indicates that there are four pairs of propellers

included in the conguration for Quad-rotors and ve pairs of propellers included in the conguration

for Hexa-rotors.

2. Gain Value Settings

The new E800 ESC, with a sinusoidal drive replacing the traditional square wave drive, offers

Motor (Clockwise rotation

)

2 or

Motor (Counter-clockwise rotation)

×2 or ×3

1345 Quick-Release Propeller Pair

×4 or ×5

ESC ×4

×6 Outer ESC LED Indicator ×4

×6 USB Connector

×1 Toolbox ×1

In the toolbox: Power hub, Screws (M2.5×6.3), Screws (M3×8.1), Screws (M3×5.5), Wrench for propellers, Foam

double sided adhesive tape, 2.0 mm hexagonal wrench, etc.

Optional Package 1345 Self-tightening Propeller Pair

1242 Self-tightening Propeller Pair

DJI E800 Multirotor Propulsion System

3. Connecting the ESCs

Tools Required

Tools: Electric soldering iron & soldering tin Use: Soldering each ESC’s power cables to the power hub

1)Check the color tags on the ESC cables to identify the default color of the ESC LED indicator (red

or green). Mount the ESCs onto the appropriate positions of your aircraft according to the LED

color. Note: The LED color can be adjusted in DJI ESC Assistant.

2) Please solder each ESC to the power pads on the power hub as shown in the gure below.

Make sure that the solder is rmly attached on the power pads and that there is no possibility for

a short circuit. The power cable is a coaxial power cable. Do not damage the protector on the

red cable to avoid short circuit.

3)Connect the signal cable to your controller. The orange wire of the signal cable is for the control

signal; the brown wire of the signal cable is for the GND; and the red wire is reserved.

4)Connect the motor to the ESC. Test the motor and make sure the rotation direction of each motor

is correct. If not, switch the position of any two cables that are connecting the motor to the ESC

to change the rotation direction.

Make sure there is no short circuit or open circuit.

It is recommended that you solder a power connector onto the power hub.

4. Assembling the Propellers

Quick-Release Propellers

1) Unpack the propellers and motors.

The propellers with a CW mark should be mounted to clockwise motors, which have a black propeller

The outer power pads are for the GND cables, and the inner power pads are for the power cables.

The red core of the coaxial power cable is positive, and the shielding layer of the coaxial power

cable is negative. Make sure to solder them correctly. Try to solder the cables rmly to the power

hub at the proper length (the wire should be just long enough to reach the soldering point, without

any extra wire bunched up before the soldering point) and outward facing.

To the controller

ESC signal cable

Power cable

Power hub

ESC

Motor

improved acceleration and deceleration performance. Before using, reduce the gain values

according to your ight control system and frame to achieve the same sensitivity as older ESCs (which

use a traditional square wave drive). The table below shows typical gain values when using the E800

with a DJI A2 ight control system and a frame which has a diagonal wheelbase of 580 mm:

Basic Attitude

Pitch Roll Yaw Pitch Roll Vertical

60% 60% 60% 204% 204% 100%

DJI E800 Multirotor Propulsion System

Clockwise Motor Counter- clockwise Motor

CW CCW

Propeller Mount

Securing Spring

2) Align the gap A inside the propeller nut with a n B on the Propeller Mount.

3) Press the propeller down onto the mount rmly and, while holding the propeller pressed down,

rotate the propeller in the lock direction until you feel it secure in place.

4) To remove the propeller, press the propeller down rmly and, while holding the propeller pressed

down, rotate the propeller in the unlock direction until it can be removed easily.

Active braking function is enabled by default, and is for use with the standard quick-

release propellers. Using this function with self-tightening propellers may cause the

propellers to y off or other ight problems.

Be sure to press the propellers down rmly until they are all the way down before rotating

to attach or detach them from the motors. Otherwise the propeller or propeller mounts

may be damaged.

When attaching a new propeller for the rst time, it may not secure in place properly after

rotating, because the hole on the propeller nut is blocked. In this case, pull the propeller

up to help lock it in position. Then hold the motor in place and try to rotate the propeller.

If it can’t be loosened without pressing down, it is locked in place.

When storing for an extended period, remove the quick-release propellers to prevent

undue wear on the spring locks.

Active braking: The motor will provide reverse torque actively to slow down the propeller,

and the rotational energy will be recovered.

Lock: Tighten the propeller by rotating it in this direction.

Unlock: Remove the propeller by rotating it in this direction.

screw and a CW mark on the propeller mount. The propellers without the CW mark should be mounted to

counter-clockwise motors, which have a silver propeller screw and a CCW mark on the propeller mount.

Attaching the

propeller

DJI E800 Multirotor Propulsion System

Self-tightening Propellers (Optional)

1) Select “Self-tightening propeller” in the DJI ESC Assistant. (Refer to 7. Updating your ESCs

Page 7 for details)

2) Remove the two screws (M3) on the top of the motor. Then remove the propeller mount and

securing spring.

3) Attach the propeller with a silver nut onto the counter-clockwise motor (which has a silver

propeller screw). Attach the propeller with a black nut onto the clockwise motor (which has a

black propeller screw).

4) Tighten the propeller by rotating it in the lock direction .

5) Remove the propeller by rotating it in the unlock direction .

“Quick-release propeller” is set by default. When changing the type of the propeller, be

sure to select the corresponding type in the DJI ESC Assistant.

DO NOT use any thread locker on the propeller or motor threads.

6 × M3-6H

Thread depth

3 mm

16 mm

25 mm

19 mm 12 mm

4 × M3-6H Thread depth 4 mm

13 mm

The screw size is M3. Mount the motors using appropriate screws.

Note the thread depth and the size of the screws. Using screws that are too long or too

large may damage the motor.

5. Mounting the Motors

Mount each motor to a frame arm according to the size of the assembly hole.

6. ESC Ports Description

There are two ports on every ESC. They are Data/ESC Firmware Update Port and Outer ESC

LED Port. Identify the marks on the ESC.

Assembly hole on the top of the motor without

the propeller mount and securing spring

Assembly hole on the bottom of the motor

DJI E800 Multirotor Propulsion System

8. ESC LED Indicators & Sound Description

The description is the same for both outer ESC LED indicators and inner ESC LED indicators, as

shown below:

LED Indicators Sound Description

Yellow, Green blinking in turn None Motor is being recognized.

Red or Green blinking slowly 1356 Ready.

—/

—

Solid Red or Green None Motor starts normally.

Unplug any other serial devices connected to your PC before updating. Then follow the instructions below:

1) Download the ESC Assistant installer from the DJI website. Run the installer and follow the

prompts to nish the installation.

2) Connect one end of the USB Connector to the Data/ESC Firmware Update Port. Connect the

other end of the USB Connector to a PC with a Micro-USB cable. Power on the ESC. DO NOT

disconnect until conguration is nished.

3) Run the ESC Assistant and wait for the ESC to connect. Watch the indicators on the bottom of

the screen. When connected successfully, the Computer Connection status will be solid green

and Data Exchange Indicator will blink blue.

4) Click on the [View] page. In the “ESC” section, check the current rmware version and ensure

the installed rmware is the latest version. If not, click the link and follow the prompts to upgrade.

5) The color of the ESC LED indicators, the type of propeller, etc. can also be adjusted through the

DJI ESC Assistant.

The DJI ESC Assistant supports Windows XP, Windows 7 and Windows 8 (32 or 64 bit).

Ensure your ESC rmware matches the motor you will attach it to. Refer to the tag on back

of the ESC to see the default rmware version.

Mount the outer ESC LED indicators according to your needs.

The Data/ESC Firmware Update Port is used to update the ESC rmware

and adjust the ESC. To do this, visit the ofcial DJI website to download

the DJI ESC Assistant.

http://www.dji.com/product/e800/download

7. Updating Your ESCs

ESC USB Connector PC

DJI E800 Multirotor Propulsion System

Red, Yellow blinking in turn

None Fail to Self-Test.

BB---BB---BB---BB… Input voltage is abnormal.

BBB----BBB----BBB… The motor parameters don’t match the

rmware data saved in the ESC.

Quick Yellow blinking BBBBBB…

Throttle stick is not at the bottom position.

Slow Yellow blinking B--------B--------B… No signal input.

Quick Red blinking None Error, land your aircraft immediately*

* You can learn more about any errors by connecting the ESC to the DJI ESC Assistant.

You can understand the working status by observing the LEDs and listening to the sound

of the ESC.

9. Specications

Max Thrust 2100 g/rotor @ 25 V Sea Level

Takeoff Weight Recommended 800 g/rotor

Battery Recommended 6 S LiPo

Working Temperature -5°C ~ 40°C

ESC

Max Allowable Voltage 26 V

Max Allowable Current (Persistent) 20 A

Signal Frequency 30 Hz ~ 450 Hz

Battery 3 S ~ 6 S LiPo

Motor

Stator Size 35×10 mm

KV 350 rpm/V

Weight 106 g

Propeller

Diameter / Thread Pitch 1345 Propellers: 13×4.5 inch

1242 Propellers: 12×4.2 inch

If you have any questions about this document, please contact DJI

by sending a message to [email protected].

The content is subject to change.

Download the latest version from

http://www.dji.com/product/e800

Inhaltsverzeichnis

Andere dji Drohnen- und Quadcopter-Zubehör Handbücher

dji

dji RD2412R Bedienungsanleitung

dji

dji AGRAS T40 Bedienungsanleitung

dji

dji Snail Bedienungsanleitung

dji

dji FC7BMC Bedienungsanleitung

dji

dji OSMO ACTION 3 Bedienungsanleitung

dji

dji FPV GOGGLES Bedienungsanleitung

dji

dji E-Port Development Lit Bedienungsanleitung

dji

dji ZENMUSE XT 2 Bedienungsanleitung

dji

dji RC 2 Bedienungsanleitung

dji

dji datalink 3 Bedienungsanleitung

dji

dji 1345 Bedienungs- und Wartungsanleitung

dji

dji AGRAS T50 Bedienungsanleitung

dji

dji MATRICE 300 RTK Bedienungsanleitung

dji

dji Aeroscope Mobile Bedienungsanleitung

dji

dji Snail Bedienungsanleitung

dji

dji GO 4 Bedienungsanleitung

dji

dji Osmo Z-Axis Bedienungsanleitung

dji

dji RoboMaster RMEM01 Bedienungsanleitung

dji

dji Zenmuse X5 Bedienungsanleitung

dji

dji ACTION 2 Bedienungsanleitung

dji

dji DROP SYSTEM NAV LIGHT EDITION Bedienungsanleitung

dji

dji E5000 PRO Bedienungsanleitung

dji

dji Phantom 4 RTK Bedienungsanleitung

dji

dji Aeroscope AS-F1800 Bedienungsanleitung

Beliebte Drohnen- und Quadcopter-Zubehör Handbücher anderer Marken

A2Z Drone Delivery

A2Z Drone Delivery RDS2 Bedienungsanleitung

ParaZero

ParaZero SafeAir Mavic Bedienungsanleitung

JT SS125 Bedienungsanleitung

RunCam

RunCam Phoenix HD Bedienungsanleitung

DRS

DRS DRS-M210-V2 Bedienungsanleitung

Kogan

Kogan 4K GALAXY Bedienungsanleitung

Opale Parachutes

Opale Parachutes SAFETECH 3.2K ST60 Bedienungsanleitung

Flycolor

Flycolor X-Cross Mini 4in1 Bedienungsanleitung

ParaZero

ParaZero SafeAir Phantom Bedienungsanleitung

HOBBYEAGLE

HOBBYEAGLE A3 Mini Bedienungsanleitung

TCMM RC

TCMM RC AC 220 Bedienungsanleitung

iKarus

iKarus Profi Gyro Bedienungsanleitung

R2TECK

R2TECK NEXG1 Bedienungsanleitung

Hesai

Hesai Pandar40P Bedienungsanleitung

Flycolor

Flycolor X-Cross HV 2 Series Bedienungsanleitung

CZZN

CZZN GL60 ZOOM Bedienungsanleitung

PowerVision

PowerVision PowerEgg Bedienungsanleitung

A2Z Drone Delivery

A2Z Drone Delivery RDS1 Bedienungsanleitung

dji E800 Bedienungsanleitung

Beliebte Drohnen- und Quadcopter-Zubehör Handbücher anderer Marken