Dji ZENMUSE H20 Series Bedienungsanleitung

2020.05

v1.0

User Manual

ZENMUSE H20 SERIES

Using this Manual

Legend

Warning Important Tips

DJI Pilot App Download

The DJI Pilot app is required when using Zenmuse H20 series.

Scan the QR code or visit http://www.dji.com/zenmuse-h20-seires/downloads to download and install

the app.

Searching for Keywords

Search for keywords such as “battery” and “install” to nd a topic. If you are using Adobe Acrobat

Reader to read this document, press Ctrl+F on Windows or Command+F on Mac to begin a search.

Navigating to a Topic

View a complete list of topics in the table of contents. Click on a topic to navigate to that section.

Printing this Document

This document supports high resolution printing.

Caution

1. Please store the camera in a dry and ventilated area at normal temperature, to avoid fogging the

lenses due to excessive ambient humidity. If the lenses fog up, the water vapor will usually dissipate

after turning on the device for a while. The recommended storage environment is a relative humidity

less than 40% at a temperature of 20±5 ℃.

2. Do not expose the infrared camera lenses to a strong energy source such as the sun, lava or laser

beam. The temperature of the observation target should not exceed 800℃, otherwise it will burn

the camera and cause permanent damage.

3. Do not place the product under direct sunlight, in areas with poor ventilation, or near a heat source

such as a heater.

4. Do not frequently power on/off the product. After it is turned off, wait at least 30 seconds before

turning back on, otherwise the product life will be affected.

5. Under stable laboratory conditions, the Zenmuse H20 series achieves an IP44 protection rating by

IEC60529 standards. However, this protection rating is not permanent and may reduce over time

after long-term use.

6. Make sure the gimbal port and gimbal surface are free from any liquid before installation.

7. Make sure the gimbal is securely installed onto the aircraft, the microSD card slot cover is clean

and rmly in place.

8. Make sure the gimbal surface is dry before opening the microSD card slot cover.

9. Do not plug or unplug the microSD card during use.

10. Do not touch the surface of the camera lenses and keep it away from hard objects, as doing so

may lead to blurred images and affect the imaging quality.

11. Clean the surface of the camera lenses with a soft, dry, clean cloth. Do not use alkaline

detergents.

Contents

Using this Manual 2

Legend 2

DJI Pilot App Download 2

Caution 3

Contents 4

Introduction 5

Installation 6

Supported Aircraft 6

Mounting the Zenmuse H20 Series 6

Remote Controller Operation 7

DJI Pilot App 8

Basic Functions 8

Intelligent Functions 15

Updating Firmware 16

Specications 17

Introduction

The Zenmuse H20 gimbal and camera features a zoom and wide camera. Operators can quickly

switch to a high-magnication zoom image for detailed observation after recognizing the target from

the wide camera view. The Zenmuse H20T also features a Longwave Infrared Thermal Camera, which

can provide both infrared and visual images simultaneously. Both the Zenmuse H20 and H20T are

equipped with a laser rangender, providing distance and location information applicable to various

missions such as search and rescue, inspection, and more. For optimal performance, the Zenmuse

H20 Series is compatible with the Matrice 300 RTK aircraft.

Zenmuse H20

1. Gimbal Connector

2. Pan Motor

3. Zoom Camera

4. Laser Rangender

5. Wide Camera

6. Tilt Motor

7. Roll Motor

8. microSD Card Slot

Zenmuse H20T

6. Zoom Camera

7. Tilt Motor

8. Roll Motor

9. microSD Card Slot

1. Gimbal Connector

2. Pan Motor

3. Wide Camera

4. Laser Rangender

5. Infrared Thermal

Camera

Installation

Supported Aircraft

Matrice 300 RTK

Mounting the Zenmuse H20 Series

The following installation display uses the Zenmuse H20 as an example.

1. Remove the gimbal cap and lens protector.

2. Rotate the gimbal connector of the Matrice 300 RTK aircraft to the unlocked position and insert the

gimbal, and then rotate the gimbal connector to the locked position.

Hold the gimbal connector rmly and apply a steady, rm rotating force when attaching or

detaching the gimbal.

Ensure the microSD card slot cover is rmly in place to prevent dust or moisture entering

during usage or transportation.

The Zenmuse H20 series is a delicate instrument. Do not disassemble the gimbal or camera

as this will cause permanent damage.

Remote Controller Operation

Adjust the gimbal’s tilt using the left dial and adjust its pan by the right dial. Press the shutter button or

record button to take photos or record video. Toggle the 5D button to adjust the zoom (up and down)

and EV value (left and right). The customizable button C1 can be used to recenter the gimbal, and the

customizable button C2 can be used to switch between the main and auxiliary screen.

1. Left Dial

Turn to adjust the gimbal’s tilt.

2. Record Button

Press to start/stop recording video.

3. Shutter Button

Press to take a photo, you can set the photo mode as single or interval in the DJI Pilot App. Taking

single photo is supported during video recording.

4. Right Dial

Turn to adjust the gimbal’s pan.

5. 5D Button

The default function is as follows. The function for this button can be customized in the DJI Pilot

App.

Left: Decrease EV value

Right: Increase EV value

Up: Zoom in

Down: Zoom out

6. Customizable Button C2

The default function is to switch between the main and auxiliary screen. The function for this button

can be customized in the DJI Pilot App.

7. Customizable Button C1

The default function is to recenter the gimbal. The function for this button can be customized in the

DJI Pilot App.

DJI Pilot App

The touch interface can be used for capturing photos, recording videos and playback. The visual

cameras support intelligent functions such as High-Res Grid Photo and Night Scene, while the

infrared thermal camera supports Digital Zoom, Spot Meter, Palette and Isotherm functions, which can

all be congured in the app.

Among the following functions, those marked with * are only applicable to the infrared thermal

camera of the Zenmuse H20T.

Basic Functions

You can view the liveview from the Zenmuse H20 series and change camera settings in Camera View.

19:29

GPS 12 2.4G 80%

100% 26.1v

26.1v

)39

0(18

10 X

2 X

5.0 X

ZOO

100

1/800

-0.3

(































222m

130.2 ALT

ASL1234.5



63'

(

)









1215

:,'(

In Flight (GPS)

$)&

ZOOM 5.0X

1 2 3 5

1. Laser Ranging

Tap to enable the laser ranging function. Laser ranging can measure the distance of objects

within the measurement range, and displays the distance from the aircraft, relative height and GPS

position of the measured object in the middle of the screen. After enabling this function, you can

save the current camera view with laser ranging information by tapping the screenshot button. The

image will be stored in the remote controller.

NG 300m 1300m

+45.3489984, -45.4598989

ALT

2. Camera and Zoom

Shows the camera of the current liveview and its zoom ratio.

3. Camera Parameters

Shows the camera’s current shoot/record parameters.

Zenmuse H20 Series User Manual

4. Focus Mode

Tap to switch the focus mode. Various focus modes are supported: MF (manual focus), AF-C

(continuous autofocus) and AF-S (single autofocus).

5. Auto Exposure Lock

Tap to lock the exposure value.

6. Camera Settings

Tap to enter the photo and video settings.

• Photo Settings

Photo Mode: includes Single Shot, High-Res Grid Photo, and Interval (2/3/5/7/10/15/20/30/60 s)

Image Ratio: 4:3

Image Format: JPEG

Save Photo: Includes Current View, Wide Photo, Zoom Photo and Infrared Photo. Current view will save

the photo taken by the current camera, but in SBS display mode of the infrared thermal camera, it will

save the screenshot instead. Photos will be saved in the microSD card in the gimbal and camera.

• Video Settings

Video Size: Zoom: 4KP30, 1080P30

Wide: 1080P30

IR: 640P30

Video Format: MP4

Save Video: Includes Current View, Wide Video, Zoom Video and Infrared Video. Current view will

save a recording of the current liveview of the app (not the HD camera feed). Videos will be saved

in the microSD card in the gimbal and camera.

• General Settings

Night Scene

If the main screen shows the zoom camera view, you can enable Night Scene mode. In night scene

mode, the zoom camera will switch the IR lter to optimize for imaging in low-light environments.

This function is only available for the zoom camera, tap Menu > General Settings, and then enable

Night Scene.

Add Timestamp and GPS Info

Enable or disable adding timestamps, which includes time and GPS information.

Lock Gimbal while Shooting

Enable or disable locking the gimbal while taking photos. If enabled, the gimbal will be locked

steady for a moment for shooting, to avoid imaging being affected when the aircraft is moving.

ROI (Region of Interest)*

Use this feature to manage color range distribution across the screen to maximize contrast for

regions of highest interest.

Select “Full” to evenly distribute the color spectrum across the entire image.

For instance, if there is a large patch of sky (relatively low temperature) in your image, much of

the color spectrum will be allocated to the lower range, meaning that other parts of the spectrum

will have a lower contrast. In this case, you may select “Sky excluded (33%)” or “Sky excluded

(50%)” to ignore areas of the sky so that most of the spectrum can be allocated to remaining areas,

providing higher contrast and utility for analysis.

Zenmuse H20 Series User Manual

ROI set to “Full” Sky excluded from ROI

Scene Parameter*

• DDE (Digital Detail Enhancement): Enhances image details and/or suppresses fixed pattern

noise.

• Contrast: The ratio of the black and white of the image. Colors will be richer and have more

contrast when the value is high.

• Brightness: The brightness of the image.

Gain Mode*

High Gain Mode: A narrower temperature range can be captured with a higher sensitivity to

temperature differences.

Low Gain Mode: A wider temperature range can be captured with a lower sensitivity to temperature

difference.

Temperature Alert*

After enabling the Area measurement feature, an alert temperature value can be set.

When the highest temperature in the selected area exceeds the alert value, an onscreen notication

will appear in DJI Pilot.

Auto FFC*

Enable or disable the automatic FFC calibration. The infrared thermal camera will automatically

calibrate at regular intervals.

Gridlines

Enable or disable the gridlines or diagonal.

Smart LED

Enable or disable smart LED such as frame arm LEDs or beacon.

Reset Camera Settings

Tap to reset the camera to the default settings.

Format SD card

Tap to format and remove all content from the microSD card. Operate with caution.

7. Photo/Video Toggle

Tap to switch between photo and video modes.

8. Zoom Slider (Zoom camera)

Tap to adjust the zoom magnication level of the zoom camera.

If the main screen shows the zoom camera view, the liveview will be changed directly by adjusting

the zoom. Otherwise, only the zoom camera preview box in the middle of the screen will be

changed.

Andere Handbücher für ZENMUSE H20 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere dji Drohnen- und Quadcopter-Zubehör Handbücher

dji

dji AGRAS T50 Bedienungsanleitung

dji

dji DF03 Bedienungsanleitung

dji

dji Snail Bedienungsanleitung

dji

dji Zenmuse X9 Bedienungsanleitung

dji

dji Snail Bedienungsanleitung

dji

dji E7000 Bedienungsanleitung

dji

dji FC7BMC Bedienungsanleitung

dji

dji ZENMUSE XT 2 Bedienungsanleitung

dji

dji MATRICE 300 RTK Bedienungsanleitung

dji

dji HG8001606 Bedienungsanleitung

dji

dji CINESSD Station Bedienungsanleitung

dji

dji datalink 3 Bedienungsanleitung

dji

dji RD2412R Bedienungsanleitung

dji

dji M200 Series Bedienungsanleitung

dji

dji Ronin Series Battery Power Distributor Bedienungsanleitung

dji

dji E-Port Development Lit Bedienungsanleitung

dji

dji Avata ND8 Bedienungsanleitung

dji

dji BTU Bedienungsanleitung

dji

dji S800 Bedienungsanleitung

dji

dji Snail 6048-3D Bedienungsanleitung

dji

dji OSMO ACTION 3 Bedienungsanleitung

dji

dji AGRAS T40 Bedienungsanleitung

dji

dji Aeroscope upgrade module Bedienungsanleitung

dji

dji TB60 Betriebsanleitung

Beliebte Drohnen- und Quadcopter-Zubehör Handbücher anderer Marken

A2Z Drone Delivery

A2Z Drone Delivery RDS2 Bedienungsanleitung

ParaZero

ParaZero SafeAir Mavic Bedienungsanleitung

JT SS125 Bedienungsanleitung

RunCam

RunCam Phoenix HD Bedienungsanleitung

DRS

DRS DRS-M210-V2 Bedienungsanleitung

Kogan

Kogan 4K GALAXY Bedienungsanleitung

Opale Parachutes

Opale Parachutes SAFETECH 3.2K ST60 Bedienungsanleitung

Flycolor

Flycolor X-Cross Mini 4in1 Bedienungsanleitung

ParaZero

ParaZero SafeAir Phantom Bedienungsanleitung

HOBBYEAGLE

HOBBYEAGLE A3 Mini Bedienungsanleitung

TCMM RC

TCMM RC AC 220 Bedienungsanleitung

iKarus

iKarus Profi Gyro Bedienungsanleitung

R2TECK

R2TECK NEXG1 Bedienungsanleitung

Hesai

Hesai Pandar40P Bedienungsanleitung

Flycolor

Flycolor X-Cross HV 2 Series Bedienungsanleitung

CZZN

CZZN GL60 ZOOM Bedienungsanleitung

PowerVision

PowerVision PowerEgg Bedienungsanleitung

A2Z Drone Delivery

A2Z Drone Delivery RDS1 Bedienungsanleitung

dji ZENMUSE H20 Series Bedienungsanleitung

Beliebte Drohnen- und Quadcopter-Zubehör Handbücher anderer Marken