Dji HG8001606 Bedienungsanleitung

DJI Focus Expansion Module User Guide

V1.0 2016.06

Disclaimer and Warning

Congratulations on purchasing your new DJITM product. The information in this document affects your

safety and your legal rights and responsibilities. Read this entire document carefully to ensure proper

configuration before use. Failure to read and follow instructions and warnings in this document may result

in serious injury to yourself or others, or damage to your DJI product or damage to other objects in the

vicinity. This User Manual and all other collateral documents are subject to change at the sole discretion

of DJI. For up-to-date product information, visit http://www.dji.com and click on the product page for

this product.

By using this product, you hereby signify that you have read this disclaimer and warning carefully and

that you understand and agree to abide by the terms and conditions herein. You agree that you are solely

responsible for your own conduct while using this product, and for any consequences thereof. You agree

to use this product only for purposes that are proper and in accordance with all applicable laws, rules,

and regulations, and all terms, precautions, practices, policies and guidelines DJI has made and may make

available.

DJI accepts no liability for damage, injury or any legal responsibility incurred directly or indirectly from

the use of this product. The user shall observe safe and lawful practices including, but not limited to,

those set forth in this User Manual.

DJI is a trademark of SZ DJI TECHNOLOGY CO., LTD. (abbreviated as “DJI”) and its affiliated companies.

Names of products, brands, etc., appearing in this manual are trademarks or registered trademarks of

their respective owner companies.

In the Box

Expansion Module x1

Power and Communication Cable x1

Introduction

The DJI Focus Expansion Module is used to extend the communication distance of the DJI Focus. It

is compatible with the Matrice 600 when used with the Ronin-MX or Zenmuse X5/X5R. The DJI

Focus Expansion Module can also be used to wirelessly control the Inspire 1 Pro/RAW camera’s

aperture and focus from 3.1 miles (5 km) away.

1. Antenna

2. DJI Focus Remote Controller Power Button

3. Link Button

4. DJI Focus Expansion Module Power Switch

5. Communication Port

6. Lock Knob

7. Status LED

Usage

1. Remove the original antenna from the DJI Focus Remote Controller.

Do not use the original antenna on the DJI Focus Remote Controller. Instead, use

the 5.8 GHz antenna provided with the DJI Focus Expansion Module.

2. Attach the Expansion Module to the DJI Focus Remote Controller as shown, then tighten the

lock knob to secure the Expansion Module.

3. When used with the Ronin-MX, connect the Communication Port on the Motor to the LB Port

and the P-TAP Port by using the provided Power and Communication Cable.

4. Press and hold the power button on the top of the Expansion Module to power on the DJI

Focus Remote Controller, and toggle the power switch up to power on the Expansion

Module.

Linking

The DJI Focus Expansion Module must be linked to the master remote controller of the Matrice

600 or Inspire 1 Pro/RAW in order to work.

How to Link

1. Power on the remote controller for the Matrice 600 or Inspire 1 Pro/RAW, and press the C1,

C2 and video recording buttons simultaneously. Release the three buttons when you hear a

beeping pattern consisting of 1 long beep followed by 2 short beeps, and then press the shutter

button once. The remote controller is ready to link when it starts to beep rapidly.

2. Power on the DJI Focus Expansion Module, then (a) press the link button once, or (b) on the

DJI Focus Remote Controller, go to Menu > Setting > Connect RC > Connect to begin linking.

3. The linking process is successful when the status indicator turns solid yellow or solid green.

Status LED Description

Status LED

Description

Solid red

Loader Mode

Blinks red

The device is not linked.

Solid yellow

The device is linked but not connected to the

motor or camera.

Solid green

Successfully linked and working normally

Specifications

Operating

Frequency

5.725-5.825 GHz

Transmission

Distance

50 m（the distance between the Expansion Module and the Master

Remote Controller of the Matrice 600 or Inspire 1 Pro/RAW,

unobstructed, free of interference）

Transmitter Power

(EIRP)

13 dBm

Operating

Temperature Range

-20 to 55℃

Operating Voltage

100 mA@3.7 V

FCC Compliance Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) This device must accept

any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

—Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Information

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits,

human proximity to the antenna shall not be less than 20cm during normal operation.

IC RSS Warning

This device complies with Industry Canada licence-exempt RSS standard (s). Operation is subject

to the following two conditions: (1) this device may not cause interference, and (2) this device must

accept any interference,including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio

exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.

IC Radiation Exposure Statement:

This equipment complies with IC RF radiation exposure limits set forth for an uncontrolled

environment. This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

This equipment should be installed and operated with minimum distance 20cm between the

radiator& your body.

Any Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device is in

compliance with the essential requirements and other relevant provisions of the R&TTE Directive.

A copy of the EU Declaration of Conformity is available online at www.dji.com/euro-compliance

EU contact address: DJI GmbH, Industrie Strasse. 12, 97618, Niederlauer, Germany

Inhaltsverzeichnis

Andere dji Drohnen- und Quadcopter-Zubehör Handbücher

dji

dji Zenmuse X9 Bedienungsanleitung

dji

dji RC 2 Bedienungsanleitung

dji

dji GO 4 Bedienungsanleitung

dji

dji TB47S Bedienungsanleitung

dji

dji E5000 ADVANCED Bedienungsanleitung

dji

dji 5048S Bedienungsanleitung

dji

dji Snail Bedienungsanleitung

dji

dji ZENMUSE H20 Series Bedienungsanleitung

dji

dji RoboMaster RMEM01 Bedienungsanleitung

dji

dji ACTION 2 Bedienungsanleitung

dji

dji 1345 Bedienungs- und Wartungsanleitung

dji

dji datalink 3 Bedienungsanleitung

dji

dji MATRICE 300 RTK Bedienungsanleitung

dji

dji MG Bedienungsanleitung

dji

dji FC7BMC Bedienungsanleitung

dji

dji Aeroscope AS-F1800 Bedienungsanleitung

dji

dji OSMO ACTION 3 Bedienungsanleitung

dji

dji CINESSD Station Bedienungsanleitung

dji

dji FPV GOGGLES Bedienungsanleitung

dji

dji ZENMUSE L1 Bedienungsanleitung

dji

dji AGRAS T30 Bedienungsanleitung

dji

dji Takyon Updater Bedienungsanleitung

dji

dji Smart Controller Enterprise Bedienungsanleitung

dji

dji FC7BMC Bedienungsanleitung

Beliebte Drohnen- und Quadcopter-Zubehör Handbücher anderer Marken

A2Z Drone Delivery

A2Z Drone Delivery RDS2 Bedienungsanleitung

ParaZero

ParaZero SafeAir Mavic Bedienungsanleitung

JT SS125 Bedienungsanleitung

RunCam

RunCam Phoenix HD Bedienungsanleitung

DRS

DRS DRS-M210-V2 Bedienungsanleitung

Kogan

Kogan 4K GALAXY Bedienungsanleitung

Opale Parachutes

Opale Parachutes SAFETECH 3.2K ST60 Bedienungsanleitung

Flycolor

Flycolor X-Cross Mini 4in1 Bedienungsanleitung

ParaZero

ParaZero SafeAir Phantom Bedienungsanleitung

HOBBYEAGLE

HOBBYEAGLE A3 Mini Bedienungsanleitung

TCMM RC

TCMM RC AC 220 Bedienungsanleitung

iKarus

iKarus Profi Gyro Bedienungsanleitung

R2TECK

R2TECK NEXG1 Bedienungsanleitung

Hesai

Hesai Pandar40P Bedienungsanleitung

Flycolor

Flycolor X-Cross HV 2 Series Bedienungsanleitung

CZZN

CZZN GL60 ZOOM Bedienungsanleitung

PowerVision

PowerVision PowerEgg Bedienungsanleitung

A2Z Drone Delivery

A2Z Drone Delivery RDS1 Bedienungsanleitung

dji HG8001606 Bedienungsanleitung

Beliebte Drohnen- und Quadcopter-Zubehör Handbücher anderer Marken