DMP Electronics 714-D22 Bedienungsanleitung

714-D22 Zone Expander Module

Description

The 714-D22 zone expander module allows you to increase the number of reporting zones available on DMP panels.

Refer to the panel installation guide for more information about the maximum number and type allowed per panel.

The modules connect to the panel’s 4-wire keypad bus or LX-Bus™ and are set to an address that determines the

reporting zone number. The 714-D22 provides four Class B, Style A zones for use with burglary devices.

Zone Programming

Program the zones on the zone expander module with any of the panel burglary zone types or as an Arming type

zone when used with keyswitches.

Zone Expander Data LED

The LED on the zone expander ashes each time the module responds to a poll from the panel. If there is a problem

with the panel, panel programming, or the Green data wire between the panel and the zone expander module, the

LED stops ashing.

Installing the 714-D22 Module

Mount the module outside the panel enclosure in the housing on a at surface such as a wall or single-gang box.

714-D22 Zone Wiring

This module uses a wire harness for wiring connections. Figure 1 shows the zone colors and polarity. You may use an

optional 718T Plug-in Screw Terminal that plugs into the 714-D22 to provide a screw type terminal connector for 14

to 22 gauge device wiring.

Wiring the 714-D22 Module

Connect the Red, Green, Yellow, and Black wires from the panel keypad bus or LX-Bus™ to the matching harness

wires on the 714-D22 Zone Expander.

C1 C4

CR3 TXD

Tens Ones

714-D22

Module

To Keypad Bus or LX-Bus

White/Yellow - Zone 4

White/Orange - Zone 3

White/Red - Zone 2

White/Brown - Zone 1

Black

Green

Yellow

Red 714-D22 Module -

Connect Red to LX-Bus Wire or Panel Terminal 7

714-D22 Module - install 1k EOL

–

All zones are supervised

The maximum zone line impedance is 100 Ohms

714-D22: Zone Ground Fault detected at 1500 Ohms or less

The normal operating range is:

714-D22 650 - 1900 Ohms

Figure 1: 714-D22 Wiring Diagram

InstallatIon GuIde

Digital Monitoring Products 714/715 Installation Guide

Setting Address Switches

714-D22 Zone Expanders use two rotary switches (TENS and ONES) to set the module address. For keypad bus

addresses, set the switches to match the device address. For LX-Bus addresses, set the switches to match the last

two digits of the addresses. For example, for address 02 set the switches to TENS = 0 and ONES = 2 as shown in

Figure 2.

TENS ONES

Figure 2: Switches

Keypad Bus Zone Numbers

Refer to Table 1 for keypad bus zone numbers and the panels where they operate.

Keypad

Bus

Address

Switches

Tens Ones XT30/XT50 XR100 Series XR500 Series

1 0 1 11 to 14 11 to 14 11 to 14

2 0 2 21 to 24 21 to 24 21 to 24

3 0 3 31 to 34 31 to 34 31 to 34

4 0 4 41 to 44 41 to 44 41 to 44

5 0 5 51 to 54 51 to 54 51 to 54

6 0 6 61 to 64 61 to 64 61 to 64

7 0 7 71 to 74 71 to 74 71 to 74

8 0 8 81 to 84 81 to 84 81 to 84

9 0 9 N/A N/A 91 to 94

10 1 0 N/A N/A 101 to 104

11 1 1 N/A N/A 111 to 114

12 1 2 N/A N/A 121 to 124

13 1 3 N/A N/A 131 to 134

14 1 4 N/A N/A 141 to 144

15 1 5 N/A N/A 151 to 154

16 1 6 N/A N/A 161 to 164

Table 1: Keypad Bus Zone Numbers

714/715 Installation Guide Digital Monitoring Products

LX-Bus Zone Numbers

The 714-D22 module provides 4 zones. When set to an address, the module uses four zone numbers. For example,

setting the module to the LX-Bus address 502 (TENS = 0, ONES = 2) sets the module zone numbers to 502, 503, 504,

and 505.

Refer to Table 2 for a partial listing of XR100/XR500 Series panel LX-Bus zone numbers.

Note: XR100 Series panels only use LX-Bus number one.

LX-Bus

Address

LX-Bus

Number

Switches

Tens Ones

Zone

Numbers

501 1 0 1 501 to 504

506 1 0 6 506 to 509

623 2 2 3 623 to 626

654 2 5 4 654 to 657

742 3 4 2 742 to 745

768 3 6 8 768 to 771

833 4 3 3 833 to 836

877 4 7 7 877 to 880

919 5 1 9 919 to 922

994 5 9 4 994 to 997

Table 2: LX-Bus Zone Numbers

Optional Accessories

You can replace the standard wiring harness with the optional 718T Plug-in Screw Terminal. The enclosure base can

also accommodate the 719T Terminal Boards for the 714-D22, which passes through the panel LX-Bus wiring. The

719T includes 1k EOL resistors.

Wiring Specications for Keypad and LX-Bus

1. DMP recommends using 18 or 22-gauge unshielded wire for all keypad and LX-Bus circuits. Do Not use twisted

pair or shielded wire for LX-Bus and keypad bus data circuits. To maintain auxiliary power integrity when

using 22-gauge wire do not exceed 500 feet. When using 18-gauge wire do not exceed 1,000 feet. Install an

additional power supply to increase the wire length or add devices.

2. Maximum distance for any one circuit (length of wire) is 2,500 feet regardless of the wire gauge. This distance

can be in the form of one long wire run or multiple branches with all wiring totaling no more than 2,500 feet.

As wire distance from the panel increases, DC voltage on the wire decreases.

3. Maximum number of devices per 2,500 feet circuit is 40.

Note: Each panel allows a specic number of supervised keypads. Add additional keypads in the unsupervised

mode. Refer to the panel installation guide for the specic number of supervised keypads allowed.

4. Maximum voltage drop between the panel (or auxiliary power supply) and any device is 2.0 VDC. If the voltage

at any device is less than the required level, add an auxiliary power supply at the end of the circuit. When

voltage is too low, the devices cannot operate properly.

For additional information refer to the panel installation guide and LX-Bus/Keypad Bus Wiring Application Note

(LT-2031) or the 710 Installation Guide (LT-0310).

      

2500 North Partnership Boulevard

800-641-4282

www.dmp.com

 

13385

Specications

Operating Voltage 12 VDC

Operating Current

714-D22 7mA + 1.6mA per zone

Zone Voltage

5 VDC, max 2mA

Dimensions 4.5” H x 2.75” W x 1.75” D

Zones Four Supervised Class B

Style A Power Limited

Accessories

718T Plug-in Screw Terminal

719T Terminal Boards

Compatibility

The 714-D22 is compatible with the following

panels:

XR100/XR500 Series and XT30/XT50 Series

Inhaltsverzeichnis

Andere DMP Electronics Steuereinheit Handbücher

DMP Electronics

DMP Electronics 714N-POE Installationsanleitung

DMP Electronics

DMP Electronics 1116 Bedienungsanleitung

DMP Electronics

DMP Electronics 734 Installationsanleitung

DMP Electronics

DMP Electronics RoBoard RM-G212 Bedienungsanleitung

DMP Electronics

DMP Electronics 734 Installationsanleitung

DMP Electronics

DMP Electronics 734 Installationsanleitung

DMP Electronics

DMP Electronics 867 W LX-BUS Bedienungsanleitung

DMP Electronics

DMP Electronics 400 Bedienungs- und Wartungsanleitung

DMP Electronics

DMP Electronics 263EXT Bedienungsanleitung

DMP Electronics

DMP Electronics Wiegand 734N Installationsanleitung

DMP Electronics

DMP Electronics 717 Bedienungsanleitung

DMP Electronics

DMP Electronics 708 Bedienungsanleitung

DMP Electronics

DMP Electronics Wiegand 734N Bedienungsanleitung

DMP Electronics

DMP Electronics 738Zplus Bedienungsanleitung

DMP Electronics

DMP Electronics Wiegand 734N Bedienungsanleitung

DMP Electronics

DMP Electronics 277CAN Bedienungsanleitung

DMP Electronics

DMP Electronics 734B Installationsanleitung

DMP Electronics

DMP Electronics 716 Bedienungsanleitung

DMP Electronics

DMP Electronics 711S Bedienungsanleitung

DMP Electronics

DMP Electronics 865 Bedienungsanleitung

DMP Electronics

DMP Electronics 400 Bedienungsanleitung

DMP Electronics

DMP Electronics 736V Bedienungsanleitung

DMP Electronics

DMP Electronics 780 Installationsanleitung

DMP Electronics

DMP Electronics 1134 Installationsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung