DMP Electronics SCS-104 Bedienungsanleitung

Model SCS-104 Line Card

Description

The SCS-104 provides four digital dialer (DD) lines and a network

connection for communication to DMP panels. Each card includes one

shielded eight-pin modular connector (J1) for the Ethernet network

connection. This allows the SCS-1R Receiver to accept alarm and

system messages over a network from DMP panels. Each card also

includes a non-shielded eight-pin modular connector (J3) that supports

up to four digital dialer lines, when connected to a standard RJ61 jack.

An optional PC software application, SCS-CTM Check-in Table Manager,

is available to backup the SCS-104 records of all supervised network

accounts for up to 32 different SCS-104 line cards. The SCS-CTM program

is compatible with SCS-104 Version 100 or higher. For complete operation

information, refer to the SCS-CTM User’s Guide (LT-0940). Contact DMP

Customer Service to purchase a copy of the SCS-CTM Check-in Table

Manager software.

Installing the SCS-104

Install the SCS-104 in any one of the SCS-1R positions

with the card puller in the up position. Connect the

10-position line card cable from the SCS-150 processor

card. The line card number is determined by the

processor card cable it is connected to.

THE LIGHT BROWN (PIN 1) WIRE OF THE FLAT CABLE

CONNECTOR MUST FACE UP ON THE LINE CARD.

Connecting the Phone Lines

Connect the phone line cable from the line card to

the customer supplied RJ61 jacks. Use a

standard 103J voice grade (analog) line.

Cables can be fed through the slot in

the receiver back plate. Maximum line

impedance is 100 Ohms.

The SCS-104 is registered with the FCC,

registration number CCKCN03BSCS-104;

Ringer Equivalence 0.3B.

Connecting the Network

Connect an IP network cable between

the J1 Ethernet connector on the front of

the line card and the network LAN/WAN

connection. Maximum line impedance is

100 Ohms. The SCS-104 automatically communicates UDP or TCP with DMP panels and automatically communicates with

encrypted panels using 128-bit or 256-bit AES Encryption.

Note: 256-bit encrypted messages sent to the SCS-1R receiver from an XR550E Control Panel Version 104 or higher software

will only communicate with SCS-104 Line Cards with Version 102 or higher software.

Phone Line Monitor

The SCS-104 monitors incoming phone line voltage. During a loss of phone line voltage, the SCS-104 sends a Warning: Phone

Line Trouble message (System Message 153) to the host automation or LCD display.

Power Monitor LED

The green LED labeled PWR turns on when the power supply on the line card is working properly.

SCS-104 Line Card

Red

Black

Ethernet J1

Phone

Line J3

Power

DTR

Line 1

Line 2

Line 3

Line 4

Line Card Connector

SCS-150 Receiver

Processor Card

Rack-Mounting

holes

SCS-104 Line Cards

SCS-150 Network

Connection

InstallatIon GUIDE

800-641-4282

      

www.dmp.com 2500 North Partnership Boulevard



 

15155

SCS-104 LED Indicators

The SCS-104 provides eight LEDs on the card. The table below describes the LED operation.

LED Description

Solid Flashing Off

POWER Power On N/A Power Off

DTR Data Terminal Ready N/A Processor is nearly full

LINE 1 Connected (off hook) Ringing Idle

LINE 2 Connected (off hook) Ringing Idle

LINE 3 Connected (off hook) Ringing Idle

LINE 4 Connected (off hook) Ringing Idle

LINK Indicates a valid Network connection

Indicates a valid Network connection

No Connection

LINK SPEED Connected at 100 Base-T N/A Connected at 10 Base-T

SCS-104 Programming

The SCS-104 is programmed through the SCS-150 Receiver Processor Board using a Membrane keypad or Browser

programming. For more information see the SCS-1R Installation Guide (LT-1037).

SCS-104 Software Update

Updating the software for SCS-104 Receiver Line Cards can be done using Remote Link Version 1.61 or higher.

Use the following steps to perform the SCS-104 update:

1. Remove the SCS-104 Line Card from the SCS-1R

Receiver.

2. Connect a Model 399 Programming Cable to the PROG

header (J8) on the line card and to a computer with

Remote Link.

3. Place a shorting clip across the 2 pins of the LOAD (J18)

header.

4. Reinstall the SCS-104 Line Card into the SCS-1R Receiver

to power up line card.

5. Open Remote Link and select System > Remote Update

from the drop-down menu.

6. In the Remote Update window, use the browse button

to nd the SCS104.RU software update le on your

computer's hard drive. Remote Link automatically recognizes the update for the SCS-104 and allows you to select the

COM port where the line card is connected.

7. Select Update. After the update is complete, remove the SCS-104 from the receiver and disconnect the 399 cable and

remove the shorting clip from the LOAD header. Reinstall the Line Card to begin normal operation.

Certications

NIST AES Algorithm Certicate #1760 128-bit

NIST AES Algorithm Certicate #2599 256-bit

California State Fire Marshal (CSFM)

New York City (FDNY COA #6167)

ANSI/UL 864 Fire Protective Signaling

ANSI/UL 163 Digital Alarm Communicator

ANSI/UL 1610 Central-station Burglar

ANSI/UL 365 Police Station Connected Burglar

ANSI/UL 1076 Proprietary Burglar

ULC-S559-04 Equipment for Fire Signal Receiving

Centers and Systems

ULC-S545 Standard for Residential Fire Warning

System Control Units

ULC-S304 Standard for Central and Monitoring

Station Burglar Alarm Units

ULC-C1023 Household Burglar Alarm System Units

ULC/ORD-C1076 Standard for Proprietary Burglar Alarm

Units and Systems

Andere DMP Electronics Steuereinheit Handbücher

DMP Electronics

DMP Electronics RoBoard RM-G212 Bedienungsanleitung

DMP Electronics

DMP Electronics 717 Bedienungsanleitung

DMP Electronics

DMP Electronics 716 Bedienungsanleitung

DMP Electronics

DMP Electronics 1134 Installationsanleitung

DMP Electronics

DMP Electronics 736P Radionics Bedienungsanleitung

DMP Electronics

DMP Electronics 738Zplus Bedienungsanleitung

DMP Electronics

DMP Electronics Wiegand 734N Installationsanleitung

DMP Electronics

DMP Electronics 893A Bedienungsanleitung

DMP Electronics

DMP Electronics 263EXT Bedienungsanleitung

DMP Electronics

DMP Electronics 1116 Bedienungsanleitung

DMP Electronics

DMP Electronics 714 Bedienungsanleitung

DMP Electronics

DMP Electronics RoBoard RM-G144 Bedienungsanleitung

DMP Electronics

DMP Electronics 714N-POE Installationsanleitung

DMP Electronics

DMP Electronics 893A Bedienungsanleitung

DMP Electronics

DMP Electronics 708 Bedienungsanleitung

DMP Electronics

DMP Electronics 734INT Installationsanleitung

DMP Electronics

DMP Electronics 736P Radionics Installationsanleitung

DMP Electronics

DMP Electronics 734 Installationsanleitung

DMP Electronics

DMP Electronics 734N-WIFI Administratorhandbuch

DMP Electronics

DMP Electronics 734 Installationsanleitung

DMP Electronics

DMP Electronics 712-8 Bedienungsanleitung

DMP Electronics

DMP Electronics 736V Bedienungsanleitung

DMP Electronics

DMP Electronics 865 Bedienungsanleitung

DMP Electronics

DMP Electronics Wiegand 734N Installationsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung