DMP Electronics 734INT Installationsanleitung

INSTALLATION AND PROGRAMMING GUIDE

734INT Access

Control Module

About the 734INT....................................... 1

Power Supply......................................................... 1

Zone Terminals ...................................................... 1

Annunciators.......................................................... 1

Indicator LEDs ....................................................... 1

Form C Relay......................................................... 2

Programming Connection................................ 2

Keypad In and Out Connections ................... 2

PCB Features...............................................3

Install the 734INT .......................................4

Mount the 734INT ............................................... 4

Wire the Access Control Lock........................ 5

Isolation Relay (optional) ................................. 7

Install the 333Suppressor ............................... 8

Wire the Zone Terminals................................... 9

Connect a Wiegand Card Reader................. 11

Set the 734INT Address...................................14

TABLE OF CONTENTS

Program the Panel.................................... 17

Device Setup ........................................................ 17

Device Number .................................................................. 17

Device Name.......................................................................17

Device Type .........................................................................18

Communication Type.......................................................18

Program the 734INT................................. 19

Programmer Menu ............................................20

Initialization Options........................................20

Access Options ...................................................21

Activate Zone 2Bypass ..................................................21

Activate Zone 3 Request to Exit.................................23

Activate Onboard Speaker ...........................................24

Card Formats.....................................................................24

Require Site Code............................................................28

Number of User Code Digits .......................................29

Card Format Added/Changed (Custom Format)29

No Communication with Panel .................................. 30

Remove Keypad..................................................31

Keypad Bus Wiring Speciﬁcations.........32

Public Card Formats ................................33

International Certiﬁcations.................... 34

Intertek (ETL) Listed........................................34

Product Speciﬁcations ........................... 36

Readers and Credentials .........................37

Digital Monitoring Products, Inc. | 734INT Installation and Programming Guide 1

Annunciators

An onboard programmable piezo provides

local annunciation at the 734INT. You can

also connect a variety of switched ground

annunciators to the 734INT for remote

annunciation.

Indicator LEDs

The 734INT provides three indicator LEDs:

• RELAY (red) turns on for the same

duration as the door strike relay.

• WIEGAND (yellow) turns on for one

second to indicate receipt of valid input.

• DATA (green) indicates that the module

is communicating with the panel.

The 734INT Access Control Module allows you to use the powerful, built in access control

capability of DMP Panels using smartcard, proximity, mag stripe, or biometric readers, or

other compatible authentication devices. The 734INT includes the following features:

Power Supply

The 734INT operates at 12/24VDC from

the power supply supporting a door’s

magnetic lock or door‑strike.

Warning: To avoid the risk of

equipment damage, do not exceed

750mA total output current for

zones connected to the module.

Zone Terminals

Zones 1 ‑ 4on the 734INT can be

programmed for a variety of burglary or

access control applications.

ABOUT THE 734INT

2 734INT Installation and Programming Guide | Digital Monitoring Products, Inc.

Form C Relay

The 10Amp Form C relay draws up to

35mA of current. Refer to “Wire the

Access Control Lock” and “Isolation Relay

(optional)” in this document for more

information.

Programming Connection

The 734INT also provides a keypad

programming connection that allows

you to use a standard DMP LCD keypad

for initial setup. Programming can be

completed using a keypad connected to

the 734INT or from XR150INT/XR550INT

Series panels.

Keypad In and Out

Connections

The keypad in (KYPD IN) connection

receives and transmits data to the panel

Keypad Bus or AX‑Bus.

The keypad out (KYPD OUT) connection

receives and transmits data out to

other keypads or modules. Install a

dual connector four‑position harness

to allow daisy chain connection to

other devices, up to the maximum

number of devices supported. XR150INT

Series panels support up to 8devices.

XR550INTSeries panels support up to

16devices. When using the AX‑Buses with

XR550INT devices, you can have 32 doors,

expandable to 96.

Caution: When the 734INT is powered

from 24VDC, do not connect devices

to KYPD OUT header.

Digital Monitoring Products, Inc. | 734INT Installation and Programming Guide 3

PCB FEATURES

RED

PROG

RED

KYPD OUT

DATA

XMT LED

WIEGAND

READ LED

RELAY

GRN

YEL

RED + –

Piezo

1234 5 6 7 810 11 12 13 14

LC ASREDWHTGRN BLK Z1 Z2 Z3 Z4+ Z4–RA GND GND

KYPD IN

RED

1 2 3 4

Door Relay

Terminal

Reader

Inputs

Status

Indicator

Outputs Zones

To Panel

Keypad Bus

or AX-Bus

To Other

Keypad Bus

or AX-Bus

Piezo

Indicator

LEDs

Keypad

Programming

Header

Address Dip

Switches

Figure 1: PCB Features

4 734INT Installation and Programming Guide | Digital Monitoring Products, Inc.

INSTALL THE 734INT

Mount the 734INT

The module comes in a high‑impact plastic housing that you can mount directly to a

wall, backboard, or other ﬂat surface.

For easy installation, the back and ends of the 734INT housing have wire entrances.

The back also contains multiple mounting holes that allow you to mount the module

on a single‑gang switch box. DMP recommends mounting the 734INT near the

protected door. Refer to Figure 2 for mounting hole locations on the housing base.

1. Remove the PCB from the

plastic housing by loosening

the clips on one side and gently

lifting it out of the housing base.

2. Insert the included screws in the

desired mounting hole locations

and tighten them to secure the

housing to the surface.

3. Reinstall the PCB in the housing

base.

Mounting Holes

Figure 2: Mounting Hole Locations

Digital Monitoring Products, Inc. | 734INT Installation and Programming Guide 5

Wire the Access Control Lock

The 734INT provides a Form C (SPDT) relay for controlling locks and other

electronically‑controlled barriers. The three relay terminals marked NO C NC allow

you to connect the device wiring to the relay for module control.

Use an additional power supply to power magnetic locks and door strikes. See

Figure 3and Figure 4for typical magnetic lock and door strike wiring.

The Form C relay draws up to 35mA of current and contacts are rated for 10Amps

(resistive) at 12/24VDC. When connecting multiple locks to the Form C relay, the

total current for all locks cannot exceed 10Amps. If the total current for all locks

exceeds 10Amps, problems may arise and an isolation relay may be needed. Refer

to “Isolation Relay (optional)” for more information.

Model 333

Suppressor

–+

12/24 VDC

Power Supply

Normally Closed

Magnetic Door

Lock

Mag lock positive

to Terminal NC

Power supply positive

to Terminal C

Mag lock negative to

power supply negative

Figure 3: Typical Magnetic Lock Wiring

Model 333

Suppressor

–+

12/24 VDC

Power Supply

Normally Open

Door strike positive

to Terminal NO

Power supply positive

to Terminal C

Door strike negative to

power supply negative

DC Door Strike

Figure 4: Typical Door Strike Wiring

6 734INT Installation and Programming Guide | Digital Monitoring Products, Inc.

KYPD IN / KYPD OUT Connections

• KYPD IN (Keypad In): Receives and transmits data to the panel Keypad bus/AX‑

Bus.

• KYPD OUT (Keypad Out): Receives and transmits data out to other keypad(s) or

module(s). Install a dual‑connector harness to allow connection to other devices

up to the maximum number of devices supported.

When the 734INT is powered from 24VDC, do not connect devices to KYPD OUT header.

Status LEDs

The 734INT board contains three status LEDs.

• The Red LED turns on for the same duration as the door strike relay.

• The Yellow LED turns on for one second to indicate receipt of a valid input

determined by card format programming.

• The Green LED indicates data sent to the panel.

Inhaltsverzeichnis

Andere DMP Electronics Steuereinheit Handbücher

DMP Electronics

DMP Electronics RoBoard RM-G146 Bedienungsanleitung

DMP Electronics

DMP Electronics 861 Bedienungsanleitung

DMP Electronics

DMP Electronics 711S Bedienungsanleitung

DMP Electronics

DMP Electronics 716 Bedienungsanleitung

DMP Electronics

DMP Electronics RoBoard RM-G212 Bedienungsanleitung

DMP Electronics

DMP Electronics 734 Installationsanleitung

DMP Electronics

DMP Electronics 734N Series Installationsanleitung

DMP Electronics

DMP Electronics 1134 Installationsanleitung

DMP Electronics

DMP Electronics 400 Bedienungs- und Wartungsanleitung

DMP Electronics

DMP Electronics 714N-POE Installationsanleitung

DMP Electronics

DMP Electronics RoBoard RM-G145 Bedienungsanleitung

DMP Electronics

DMP Electronics 1134 Installationsanleitung

DMP Electronics

DMP Electronics 734N Series Installationsanleitung

DMP Electronics

DMP Electronics 714-D22 Bedienungsanleitung

DMP Electronics

DMP Electronics 893A Bedienungsanleitung

DMP Electronics

DMP Electronics 734N-WIFI Administratorhandbuch

DMP Electronics

DMP Electronics XR100 Bedienungsanleitung

DMP Electronics

DMP Electronics RoBoard RM-G144 Bedienungsanleitung

DMP Electronics

DMP Electronics 263EXT Bedienungsanleitung

DMP Electronics

DMP Electronics SCS-104 Bedienungsanleitung

DMP Electronics

DMP Electronics 400 Bedienungsanleitung

DMP Electronics

DMP Electronics RoBoard RM-G211 Bedienungsanleitung

DMP Electronics

DMP Electronics 708 Bedienungsanleitung

DMP Electronics

DMP Electronics 738Zplus Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung