DMP Electronics Wiegand 734N Installationsanleitung

INSTALLATION AND PROGRAMMING GUIDE

734N Wiegand

Interface Module

Digital Monitoring Products, Inc. | 734 Installation and Programming Guide a

Table of Contents .......................................a

About the 734N .......................................... 1

Power Supply......................................................... 1

Zone Terminals ...................................................... 1

Annunciators.......................................................... 1

Indicator LEDs ....................................................... 1

Form C Relay......................................................... 2

Programming Connection................................ 2

Keypad In and Out Connections ................... 2

PCB Features...............................................3

Install the 734N...........................................4

Mount the 734N ................................................... 4

Wire the Electronic Lock.................................. 5

Isolation Relay ...................................................... 6

Install the 333 Suppressor ............................... 7

Wire the Zone Terminals................................... 8

Connect a Card Reader....................................10

Set the 734N’s Address....................................12

TABLE OF CONTENTS

Program the 734N.................................... 15

Program Start Display ...................................... 15

Initialization Option ...........................................15

Initialize Conﬁrm Option .................................16

Activate Zone 2 Bypass...................................16

zone 2 Bypass Time...........................................17

Relock on zone 2 Change ...............................17

Activate zone 3 Request to Exit...................18

Zone 3 REX Strike Time...................................19

Activate On-board Speaker ...........................19

Card Options........................................................19

Custom Card Deﬁnitions ......................... 21

Wiegand Code Length..................................... 21

Site Code Position and Length .....................21

User Code Position and Length................... 22

Require Site Code .............................................22

Site Code Display ..............................................22

Enter Site Code .................................................23

Number of User Code Digits.........................23

b 734 Installation and Programming Guide | Digital Monitoring Products, Inc.

No Communication with Panel ....................24

Remove Keypad.................................................25

Keypad Bus Wiring Speciﬁcations........ 26

Compliance Listing Speciﬁcations ........27

UL Commercial Fire.......................................... 27

UL Access Control............................................. 27

ULC Commercial Burglary (XR150/XR550

Series Panels)...................................................... 27

Certiﬁcations.............................................28

Underwriters Laboratory (UL Listed)........28

International Certiﬁcations.................... 29

Intertek (ETL) Listed........................................29

Product Speciﬁcations ........................... 30

Accessories................................................ 31

Proximity Readers..............................................31

Proximity Credentials........................................31

Digital Monitoring Products, Inc. | 734 Installation and Programming Guide 1

ANNUNCIATORS

An on-board programmable piezo provides local

annunciation at the 734N. You can also connect

a variety of switched ground annunciators to the

734N for remote annunciation.

INDICATOR LEDS

The 734N provides three indicator LEDs. The

red LED turns on for the same duration as the

door strike relay. The yellow LED turns on for one

second to indicate receipt of a valid Wiegand

input. The green LED indicates that data is being

sent to the panel.

The 734N Wiegand Interface Module allows you to add IP network access control capability to

XR150/XR550 Series and XR150INT/XR550INT Series panels using proximity credential or mag-stripe

card readers. It also allows you to use the powerful built-in access control capability of DMP Panels.

DMP panels provide access control, arming, and disarming using proximity, mag-stripe, biometric or

other Wiegand-output authentication devices.

Connect a 734N to a DMP panel’s keypad bus or AX-Bus™to use the powerful built-in access control

capability of DMP panels. The 734N includes the following features:

POWER SUPPLY

The 734N operates at 12/24VDC from the power

supply supporting a door’s magnetic lock or

door-strike. It also provides a 10 Amp Form C

relay contact for lock control.

ZONE TERMINALS

Zones 1, 2, and 3 on the 734N can be

programmed for a variety of burglary or access

control applications. Zone 4 is a class B, style A

circuit that may be programmed as a ﬁre zone.

ABOUT THE 734N

2 734 Installation and Programming Guide | Digital Monitoring Products, Inc.

FORM C RELAY

The 734N’s Form C relay draws up to 35mA of

current. Refer to the NC/C/NO (Dry Contact

Relay) and the Isolation Relay sections in this

document for more information.

PROGRAMMING CONNECTION

The 734N also provides a keypad programming

connection that allows you to use a standard

DMP LCD keypad for initial setup. Programming

can be completed using a keypad connected to

the 734N, or from XR150/XR550 or XR150INT/

XR550INT Series panels.

KEYPAD IN AND OUT

CONNECTIONS

The keypad in (KYPD IN) connection receives

and transmits data to the panel keypad bus or

AX-Bus™.

The keypad out (KYPD OUT) connection receives

and transmits data out to other keypad(s) or

module(s). Install a dual connector four-position

harness to allow daisy chain connection to other

devices, up to the maximum number of devices

supported. XR150 Series panels support up to 8

devices. XR550 Series panels support up to 16

devices.

When the 734N is powered from 24VDC,

do not connect devices to KYPD OUT

header.

Digital Monitoring Products, Inc. | 734 Installation and Programming Guide 3

PCB FEATURES

DC INPUT

WIEGAND

INPUTS ZONES

PIEZO

INDICATOR

LEDS

DOOR RELAY

NETWORK

CONNECTION

4 734 Installation and Programming Guide | Digital Monitoring Products, Inc.

INSTALL THE 734N

The 734N comes in a high-impact plastic housing that you can mount directly to a wall,

backboard, or other ﬂat surface.

For easy installation, the back and ends of the 734N housing have wire entrances. The back also

contains multiple screw holes that allow you to mount the 734N on a single-gang switch box. DMP

recommends mounting the 734N near the protected door.

You can also mount the 734N in a panel enclosure by following these steps:

1. Remove the 734N PCB from the plastic housing.

2. Mount the plastic standos to the panel enclosure by pressing them into place.

3. Snap the 734N onto the standos.

1MOUNT THE 734N

Digital Monitoring Products, Inc. | 734 Installation and Programming Guide 5

The 734N provides a Form C (SPDT) relay for controlling locks and other electronically-

controlled barriers. The three relay terminals marked NO C NC allow you to connect the device

wiring to the relay for module control.

Use an additional power supply to power magnetic locks and door strikes. See Figures 2 and 3

for typical magnetic lock and door strike wiring.

The Form C relay draws up to 35mA of current and contacts are rated for 10 Amps (resistive)

at 12/24VDC. When connecting multiple locks to the Form C relay, the total current for all locks

cannot exceed 10 Amps. If the total current for all locks exceeds 10 Amps, problems may arise

and an isolation relay may be needed. See the Isolation Relay section for information.

2WIRE THE ELECTRONIC LOCK

PROG

RED RED

KYPD IN

DATA

XMT LED

WIEGAND

READ LED

RELAY

NCCNO

GRNYELRED

Model 333

Supressor

Normally Closed

–

Magnetic Door Lock

12/24VDC

Power Supply

Figure 2: Typical Magnetic

Lock Wiring

PROG

RED

DATA

XMT LED

WIEGAND

READ LED

RELAY

NCCNO

GRNYELRED

Model 333

Supressor

Normally Open

–+

DC Door Strike

12/24VDC

Power Supply

Figure 3: Typical Door

Strike Wiring

6 734 Installation and Programming Guide | Digital Monitoring Products, Inc.

The Form C relay can control a device that draws less than 10 Amps of current. If a device draws

more than 10 Amp of current, or the sum of all devices controlled by the Form C relay exceeds

10 Amps, an isolation relay must be used. Refer to Figures 5 and 6 for isolation relay wiring.

3ISOLATION RELAY

Figure 4: Magnetic Lock with

an Isolation Relay

Figure 5: Door Strike with an

Isolation Relay

(optional)

Normally

Closed

Magnetic Lock Model 333

Supressor

–+

12/24VDC

Power

Supply

734N

Interface

Module

DC Input

Model 333

Supressor

Normally

Open

–+

DC Door Strike

12/24VDC

Power

Supply

734N

Interface

Module

DC Input

Andere Handbücher für Wiegand 734N

Inhaltsverzeichnis

Andere DMP Electronics Steuereinheit Handbücher

DMP Electronics

DMP Electronics 1116 Bedienungsanleitung

DMP Electronics

DMP Electronics X1 Installationsanleitung

DMP Electronics

DMP Electronics 738ZplusINT Bedienungsanleitung

DMP Electronics

DMP Electronics 712-8 Bedienungsanleitung

DMP Electronics

DMP Electronics myQ 736Q Montageanleitung

DMP Electronics

DMP Electronics 867 Style W Bedienungsanleitung

DMP Electronics

DMP Electronics ITI 738I Installationsanleitung

DMP Electronics

DMP Electronics 867 W LX-BUS Bedienungsanleitung

DMP Electronics

DMP Electronics RoBoard RM-G211 Bedienungsanleitung

DMP Electronics

DMP Electronics 780 Installationsanleitung

DMP Electronics

DMP Electronics XR100 Bedienungsanleitung

DMP Electronics

DMP Electronics 734N-WIFI Administratorhandbuch

DMP Electronics

DMP Electronics 736V Bedienungsanleitung

DMP Electronics

DMP Electronics 263EXT Bedienungsanleitung

DMP Electronics

DMP Electronics 734 Installationsanleitung

DMP Electronics

DMP Electronics 736P Radionics Installationsanleitung

DMP Electronics

DMP Electronics 716 Bedienungsanleitung

DMP Electronics

DMP Electronics 263EXT Bedienungsanleitung

DMP Electronics

DMP Electronics 714-D22 Bedienungsanleitung

DMP Electronics

DMP Electronics 861 Bedienungsanleitung

DMP Electronics

DMP Electronics Wiegand 734N Bedienungsanleitung

DMP Electronics

DMP Electronics 1134 Installationsanleitung

DMP Electronics

DMP Electronics 865 Bedienungsanleitung

DMP Electronics

DMP Electronics 734 Installationsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung