DMP Electronics Thinline Series Bedienungsanleitung

THINLINETM AND AQUALITETM LCD KEYPAD

Installation Guide

FRI 2: 52 PM

1 2 3 4

5 6 7 8

9 0 CMD

Information furnished is believed to be accurate and reliable.

This information is subject to change without notice.

DESCRIPTION

Thinline Series (7060, 7063, 7070, 7073, 7160, 7163, 7170, and 7173) and Aqualite Series

(7060A, 7063A, 7070A, and 7073A) LCD keypads oer ﬂexible features and functionality.

Each keypad provides:

• Custom 16-character home or business name in the display

• Four 2-button panic keys

• AC Power/Armed LED

• 32-character display

• Backlit keyboard and DMP logo

• Internal speaker

• Red keyboard lighting in alarm conditions

• Simple harness connection to 4-wire keypad bus

• Optional back-boxes for conduit or wall mount applications

Models 7070/A, 7073/A, 7170, and 7173

Provide four fully-programmable, Class B, Style A, supervised, power limited protection

zones that can be programmed for a variety of burglary and access control applications.

Models 7063/A, 7073/A, 7163, and 7173

Provide a built-in proximity card reader designed to read DMP/HID proximity credentials.

Models 7073/A and 7173

Provide a door strike relay and allow Wiegand input from external card readers.

INSTALL THE KEYPAD

All DMP keypad housings are designed to install on any 4” square box, 3-gang switch box,

DMP 695 and 696 back-box, or ﬂat surface.

Wiring Speciﬁcations for Keypad Bus

When planning a keypad bus installation, keep in mind the following speciﬁcations:

• DMP recommends using 18 or 22–gauge unshielded wire for all keypad circuits.

Do not use twisted pair or shielded wire for keypad bus data circuits. To maintain

auxiliary power integrity when using 22–gauge wire, do not exceed 500 feet. When

using 18–gauge wire, do not exceed 1,000 feet. Install an additional power supply

to increase the wire length or add devices.

• Maximum distance for any one circuit (length of wire) is 2,500 feet regardless of

the wire gauge. This distance can be in the form of one long wire run or multiple

branches with all wiring totaling no more than 2,500 feet. As wire distance from

the panel increases, DC voltage on the wire decreases.

• Maximum number of devices per 2,500 feet circuit is 40.

Each panel allows a speciﬁc number of supervised keypads. Add additional

keypads in the unsupervised mode. Refer to the panel installation guide for the

speciﬁc number of supervised keypads allowed.

• Maximum voltage drop between the panel (or auxiliary power supply) and any

device is 2.0VDC. If the voltage at any device is less than the required level, add an

auxiliary power supply at the end of the circuit. When the voltage is too low, the

devices cannot operate properly. Refer to the Keypad Bus Wiring Application Note

(LT-2031) and the 710 Module Installation Sheet (LT-0310) for more information.

Keypad Speciﬁcations

MODEL

NORMAL/

STANDBY

CURRENT

ALARM

CURRENT

FOUR

ZONES

INTERNAL

PROX

READER

WIEGAND

INPUT

INTERNAL

DOOR

STRIKE

RELAY

7060/A, 7160 72mA 87mA

7063/A, 7163 85mA 100mA X

7070/A, 7170 72mA+1.6mA

per active zone 87mA+2mA

per active zone X

7073/A, 7173 85mA+1.6mA

per active zone

100mA+2mA

per active zone X X X X

Table 1: Keypad Speciﬁcations

Install the Keypad

Remove the Cover

The keypad housing is made up of two parts: the cover, which

contains the circuit board and components, and the base. Use the

following steps and Figure 1 to separate the keypad cover and

base:

1. Insert a ﬂat screwdriver into one of the slots on the bottom

of the keypad and gently lift the screwdriver handle toward

you while pulling the halves apart. Repeat with the other

slot.

2. Using your hands, gently separate the front from the base

and set the cover and components aside. See Figure 1.

Harness Wiring

Use 1k Ohm EOL resistors, DMP Model 311 on keypad zones 1-4.

Models 7060/A, 7063/A, 7160, and 7163

Supplied with a 4-wire harness for panel keypad bus connection.

Models 7070/A, 7073/A, 7170, and 7173

Supplied with a 12-wire data bus/zone harness. Four wires connect to the keypad

bus. The remaining eight wires are for the four zone inputs, four wires for each

zone.

Models 7073/A and 7173

Supplied with one 5-wire output/reader harness.

Keypad

Wall

Insert small screwdriver

and lift to remove cover.

Do not twist.

Figure 1:

Removing the Keypad Cover

Install the Keypad

Firmly grasp the wires near the base and hold the outside

edges of the keypad housing. Line up the red and yellow

wires with the guides on the board to inset the connector

into the J5 keypad terminal. Observe wire colors when

connecting the red, yellow, green, and black wires to the

keypad bus. See Figure 2.

• Connect red wire to panel terminal 7

• Connect yellow wire to panel terminal 8

• Connect green wire to panel terminal 9

• Connect black wire to panel terminal 10

Additional Power Supply

If the current draw for all keypads exceeds the panel output,

provide additional current by adding a Model 505-12 auxiliary power supply.

1. Connect all keypad black ground wires to the power supply negative terminal.

2. Run a jumper wire from the power supply negative terminal to the panel common

ground terminal.

3. Connect all keypad power (+12VDC) wires to the power supply positive terminal.

Do not connect the power supply positive terminal to any panel terminal. Refer to

the 505-12 Power Supply Installation Guide if needed (LT-0453).

Keypad Bus Monitor

For listed ﬁre protective systems, the 893A Module or 277 Trouble Sounder must be installed

on the XR150/XR550 Series panel to monitor the keypad bus. It should be programmed to

sound when the keypad bus fails to operate.

Figure 2: Keypad Back Showing

Wiring Harness Assignments

Y/W

Install the Keypad

Figure 3: Keypad Back Showing Wiring

Harness Assignments

USE THE KEYPAD FOR ACCESS CONTROL

Card Readers

When a proximity credential is presented to an internal or external reader, a beep

tone is heard and the Power/Armed LEDs blink. This provides an audible and visual

acknowledgment of the credential read.

Internal Access Control Reader

The 7063/A, 7073/A, 7163, and 7173 keypads provide a built-in proximity card

reader that is compatible with most standard 125Khz Prox credentials available

from DMP and HID (1300 Series). DMP Keypads are not compatible with iClass

or other non-HID credentials. There are custom and non-standard credentials

from HID that are not compatible with DMP proximity keypads. If you are using

HID cards that have not been purchased directly from DMP, it is recommended to

thoroughly test the application fully before installation. DMP does not guarantee

compatibility with credentials not purchased from DMP. For listed access control

applications, the keypad must be installed within the protected area.

External Access Control Reader

To accept Wiegand data input from other external card readers, connect a 12VDC

external reader to the 7073/A and 7173 keypad. Connect the red and black power

wires from the reader to the power wires from the panel. These connect in parallel

with the keypad power wires. Connect the Reader (Data 1) wire to the white wire

on the 5–wire keypad harness. Connect the Reader (Data 0) wire to the green/

white wire on the 5–wire keypad harness. See Figure 4.

1K EOL

Green/White – Connect Reader Data 0

White – Connect Reader Data 1

Orange – Door Strike N/O

Gray

–

Door Strike C

Violet

–

Door Strike N/C

Yellow/White

White/Yellow

Orange White

White/Orange

Red/White

White/Red

Brown/White

White/Brown

Black – Ground

Green – Receive Data

Yellow – Send Data

Red

– Keypad Power

– Zone 4

– Zone 3

– Zone 2

– Zone 1

ExternalReader/Door Strike

7073/7073A, 7173 Keypads

All Keypads

Zones 1-4

7070/7070A, 7073/7073A, 7170/7173 Keypads

Surface and Backbox

Mounting Holes

Combined 4-square

and 3-gang switch box

Mounting Holes

Surface and Backbox

Mounting Holes

*All zones are supervised and suitable for ﬁre applications.

*Maximum zone line impedence is 100 Ohms.

*Ground fault detected at 1420 Ohms or less.

Install the Keypad