Dormakaba YD30D Handbuch
Installation & Operating Instructions
YD30D
Double Sideload Lock
2
Table of Contents
1. Document Information 3
1.1 Contents and Purpose 3
1.2 Target Group 3
2. Safety and Compliance 4
2.1 Safety Information 4
2.2 Regulatory Compliance Information 5
3. Product Information 7
3.1 Product Description 7
3.2 Package Contents 8
3.3 Technical Data 9
4. Product Dimensions 10
4.1 Lock Dimensions 10
4.2 Strike Dimensions 11
4.3 Housing Dimensions (Available Separately) 12
4.4 Dress Plate Dimensions (Available Separately) 12
4.5 Fitting Tab Dimensions (Available Separately) 13
5. Pre-Installation Assessment 14
5.1 Mounting Assessment 14
5.2 Wiring Assessment 15
5.3 Operating Mode Assessment 15
6. Mounting 16
6.1 Mortise Installation (Solid Wood) 16
6.2 Mortise Installation (Metal Extrusion) 17
6.3 Surface Mounting Installation (Solid Wood) 18
6.4 Surface Mounting Installation (Glass) 19
7. Wiring 20
7.1 Wiring Guide 20
7.2 Fail Safe Connection 20
7.3 Fail Secure Connection 20
8. Operating Mode 21
8.1 Fail Safe Operation 21
8.2 Fail Secure Operation 21
9. Maintenance 22
9.1 Maintenance and Cleaning 22
9.2 End of Service Life 22
3
1.1 Contents and Purpose
This document describes installation, connection, operation, and maintenance of the lock SL30DBL. Read the
document carefully and observe the instructions it contains. They contain important information for reliable
installation and trouble-free operation.
1.2 Target Group
Target group of these instructions are:
• Installer
• Service Technician
Installers and service technicians are skilled personnel who have the specialist knowledge required for instal-
lation, commissioning, and maintenance.
4
1. Safety and Compliance
1.1 Safety Information
WARNINGS
• Live parts inside.
• The handling and installation of this device is recommended for a professional.
• Use of an unsuitable power supply unit may cause product failure or injury.
• Do not remove the cover plates or face plate.
• Ensure installation does not expose sharp edges of the product to users.
UL REQUIREMENTS
• If the unit is installed on a fire exit door the product installation shall be allowed only if
accepted by a local AHJ authority having jurisdiction and comply with NFPA 101.
• The unit is to be connected and controlled via a UL 294 or FWAX7 listed Access Control Unit.
• That the unit shall be installed in accordance to NFPA 70 along with any additional
requirements imposed by the local authority of jurisdiction.
• Do not connect the unit to a receptacle controller by a switch.
• If the unit is installed in conjunction with panic hardware the lock shall be installed in a
manner to not impair panic device operations.
• The unit shall be powered by a UL 294 or UL 2610 listed power supply with a Class 2 power
limited output.
• All factory tested grades were not evaluated by UL.
• UL1034 rating only applies when product is installed in a mortised application.
5
1.1 Regulatory Compliance Information
This product is in compliance with the CE Directives including Electomagnetic Compatibility (EMC) Directive,
Restriction of the use of certain hazardous substances (RoHS) Directive, and Registration, Evaluation,
Authorisation and Restriction of Chemicals (REACH) Regulation.
This product is in compliance with the United Kingdom (UK) Legislation including the Electromagnetic
Compatibility Regulation 2016, and the Restriction of the Use of Certain Hazardous Substances in Electrical
and Electronic Equipment Regulations 2012.
CE and UKCA Declaration of Conformity is available at www.dormakaba.com.
EN14846:2008
1 2 3 4 5 6 7 8 9
3 X 9 0* / G 2 1 1
*Grade 0 for classification 4 ‘Suitability for use on fire/smoke doors’ applies only to the product when used
as a primary latching device for a fire/smoke door. The product is suitable for use on a fire/smoke door when
installed as an auxiliary locking device alongside a primary latching device with appropriate test evidence.
This appliance is labelled in accordance with European Directive 2012/19/EU concerning
used electrical and electronic appliances (waste electrical and electronic equipment
- WEEE). The guideline determines the framework for the return and recycling of used
appliances as applicable throughout the EU.
In Countries Outside the European Union and EEA (Norway, Iceland, and Liechtenstein): If
you wish to dispose of this product please contact your local authorities and ask for the
correct way of disposal.
This product is in compiance with the Regulatory Complaince Mark (RCM) for Australia and
New Zealand.
6
This product is regulated by the UL/CSA and bears UL/C-UL certification.
Certifications: UL294, UL1034, ULC-S533-15
UL File Number: BP7604
UL Catagories: CVXY, ALVY, FWAX7
UL294
Line Security Level I
Standby Power Level I
Attack Level I
Endurance Level IV
UL1034
Static Strength: 1,500 lbf (6,673N)
Dynamic Strength: 70 ft·lbf (95J)
Endurance: 250,000 cycles
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
residential, commercial, or industrial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
Modifications: Any modifications made to this device that are not approved by the
manufacturer may void the authority granted to the user by the FCC to operate this
equipment.
Innovation, Science and Economic Development Canada ICES-003:
CAN ICES-3(B)/NMB-3(B)
7
1.1 Product Description
The SL30DBL is a motor driven low voltage electric lock designed to secure commercial and residential swing-
through (180°) doors. The lock has been designed to address the two biggest issues in concealed electric
locking today;
1. The ability to ‘pull’ a door into alignment even if the door has not closed in a central position.
2. The ability to release when requested even if there is excessive load on the door.
The design of the SL30DBL is unique as it has two motors which independently operate two bolt pins. The bolt
pins operate on a cam action which enables each bolt pin to pull a door into place. In practice as the door
closes it may come to rest in a position that is not fully closed. The SL30DBL senses when the door is within
8mm (5/16 inch) of being fully closed in either direction and activates the bolt pin. This is an effective 16mm
(10/16 inch) alignment window. The bolt pin then rotates out and pulls the door from its resting position to
the closed and secured position.
With the door secured and locked the SL30DBL can be given an unlock signal and it will instantly unlock. If
the door is loaded (pre-load) when the unlock signal is given the SL30DBL will still unlock, even with loads
in excess of 100kg on the door from either side. Critically the ability of the SL30DBL to instantly release with
excessive pre-load on the door even occurs in the event of a power failure if the lock is configured as fail safe.
Additional features of the SL30DBL are;
• Multi-voltage input (12 - 24VDC)
• Very low current consumption
• Door position and bolt position monitors
• High physical strength
• Fail-safe / Fail-secure on-site conversion with the re-positioning of a single switch
1.1 Package Contents
1x Lock 1x Strike Plate
4x 10G self-tapping screws 1x 300mm 7-way wire loom
8
1.1 Technical Data
Materials
Bolt Stainless Steel 17-4PH
Lock / Strike Plate Stainless Steel 304
Mechanical
Bolt Extension 13mm
Door Gap max. 6mm (¼ inch)
Misalignment Correction max. 8mm (5/16 inch)
Cycle Life 1,000,000 cycles
Holding Force 10,000N (2,250 lbf) (factory tested only)
Side Load Release 6,000N (1,350 lbf) (factory tested only)
Locking Time 1.0 seconds (typical)
Unlocking Time 0.3 seconds (typical)
Environmental
Operating Temperature -10°C to +55°C
Electrical
Power Requirements 12-24 VDC ±15%
Initial Power Up Time 11 seconds
Initial Current Draw 750mA@12VDC, 400mA@24VDC
Standby Current 40mA@12VDC, 25mA@24VDC
Signal Contacts Bolt Position (NO) 30VDC max., 100mA max.
Door Position (NO)
Compliance
CE, UKCA, UL, FCC, IC, RCM, RoHS 2
9
10
1. Product Dimensions
1.1 Lock Dimensions
The dimensions shown are approximate and subject to change without prior notice.
183mm
7.205in
47mm
1.854in
3mm
0.118in
255mm
10.039in
10mm
0.394in
235mm
9.252in
10mm
0.394in
30mm
1.181in
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Dormakaba Sperren Handbücher
Dormakaba
Dormakaba ORACODE 660i Bedienungsanleitung
Dormakaba
Dormakaba STV 2 Series Bedienungsanleitung
Dormakaba
Dormakaba LA GARD 700 Series Bedienungsanleitung
Dormakaba
Dormakaba YD30S Handbuch
Dormakaba
Dormakaba 8H Series Bedienungsanleitung
Dormakaba
Dormakaba SL30DBL Cobalt Double Bedienungsanleitung
Dormakaba
Dormakaba YD30 Series Handbuch
Dormakaba
Dormakaba digital cylinder Bedienungsanleitung
Dormakaba
Dormakaba Saflok Quantum Pixel Bedienungsanleitung
Dormakaba
Dormakaba LA GARD ComboGard Pro 39E Handbuch
Dormakaba
Dormakaba M Series Bedienungsanleitung
Dormakaba
Dormakaba Confidant RFID Kit 2 Bedienungsanleitung
Dormakaba
Dormakaba ORACODE 480 Series Bedienungsanleitung
Dormakaba
Dormakaba La Gard Reset Box Bedienungsanleitung
Dormakaba
Dormakaba Axessor CIT Bedienungsanleitung
Dormakaba
Dormakaba 79 Series Montageanleitung
Dormakaba
Dormakaba GL10 Bedienungsanleitung
Dormakaba
Dormakaba RCI DE8310 V1.6 Bedienungsanleitung
Dormakaba
Dormakaba AUDITCON 2 SERIES Bedienungsanleitung
Dormakaba
Dormakaba BEST Wi-Q 45HQ Bedienungsanleitung
