Drive 14026 Bedienungsanleitung

Med-Aire Melody Alternating

Pressure Low Air Loss Mattress

Replacement System

www.drivemedical.com

OPERATOR’S MANUAL

Item # 14026

TABLE OF CONTENTS

IMPORTANT SAFEGUARDS ...............................................................................................................3

STATEMENTS & SYMBOLS.................................................................................................................4

INTRODUCTION..................................................................................................................................4

PRODUCT FUNCTIONS......................................................................................................................5

CONTROL UNIT ..................................................................................................................................5

MATTRESS ..........................................................................................................................................5

ENTRAPMENT GUIDLINES .................................................................................................................5

INSTALLATION INSTRUCTIONS.........................................................................................................6

OPERATING INSTRUCTIONS .............................................................................................................7

CLEANING ..........................................................................................................................................8

MAINTENANCE...................................................................................................................................8

MAINTENANCE TROUBLE SHOOT ....................................................................................................9

TECHNICAL SPECIFICATIONS...........................................................................................................9

LIMITED WARRANTY ........................................................................................................................10

IMPORTANT SAFEGUARDS

When using electrical products, especially when children are present, basic safety precautions should

always be followed, including the following

READ ALL INSTRUCTIONS BEFORE USING

DANGER

To reduce the risk of electrocution:

• Always unplug this product immediately after use.

• Do not use while bathing.

• Do not place or store product where it can fall or be pulled into a tub or sink.

• Do not place or drop into water or other liquids.

• Do not reach for a product that has fallen into water. Unplug immediately.

WARNING

To reduce the risk of burns, electrocution, re or injury to persons:

• A product should never be left unattended when plugged in.

• Close supervision is necessary when this product is used by, on, or near children or invalids.

• Use this product only for it intended use as described in this manual.

Do not use attachments not recommended by the manufacturer.

• Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been

dropped or damaged, or dropped into water. Return the product to a service center for examination

and repair.

• Keep the cord away from heated surfaces.

• Never block the air openings of the product or place it on a soft surface, such as a bed or couch,

where the air openings may be blocked. Keep the air openings free of lint, hair and the like.

• Never drop or insert any object into any opening or hose.

• Do not use outdoors or operate where aerosol (spray) products are being used.

• Connect this product to a properly grounded outlet only.

SAVE THESE INSTRUCTIONS

Note, caution, warning & danger statements

NOTE

Indicates some tips or some information users should be aware of.

CAUTION

Indicates correct operating or maintenance procedure in order to prevent damage to or destruction

of the equipment or other property.

WARNING/DANGER

Calls attention to a potential danger that requires correct procedures or practices in order to prevent

personal injury.

Others

Symbols on the printed label on the outside package box are as below:

Always read the operating instructions before use.

SYMBOLS

Symbol Meaning

Power ON.

Power OFF.

Series number.

Class II Medical electric equipment.

Type BF applied part.

Refer to instruction manual/ booklet.

Degree of protection against harmful ingress of water

and particulate matter.

STATEMENTS & SYMBOLS

INTRODUCTION

INDICATIONS

The Med Aire Melody Alternating Pressure and Low Air Loss Mattress Replacement System, item

# 14026, is indicated for the prevention and treatment of any and all stage pressure ulcers when

used in conjunction with a comprehensive pressure ulcer management program. It can be used in a

hospital, homecare, or other healthcare environment.

PRODUCT FUNCTIONS

CONTROL UNIT

The functions of the Med Aire Melody control unit are described below. Please refer to the gures of the Med

Aire Melody control unit in Fig A.

Power Switch (1)

Turn ON/OFF the power switch, the control unit will start/stop operation.

Pressure-adjust Knob (2)

Determine the patient’s weight and set the control knob to that weight setting on the control unit.

Normal Pressure Indicator (3)

A visible indicator (green) tells the pressure has reached a preset or user-dened level.

Low Pressure Indicator (4)

A visible indicator (orange) warns the pressure is below a preset or user-dened level.

Static/Alternating control (5)

Press ON to set the air mattress to static mode or OFF to set to alternating pressure mode.

1. Power Switch

2. Pressure-adjust Knob

3. Normal Pressure Indicator

4. Low Pressure Indicator

5. Static Control

MATTRESS

The Med Aire Melody System comes with an air cell mattress that provides low air loss, alternation and static

pressure redistribution therapy. It is composed of a combination of materials including Nylon PVC and PU.

Please refer to the specications section for details.

ENTRAPMENT GUIDELINES

The use of Bed Rails is dependent on the setting as well as the facilities protocols. Drive DeVilbiss does

not make product recommendations for any given patient. Those decisions are the responsibility of the

health care facility and/or health care professional(s) familiar with each patient’s unique requirements.

Drive DeVilbiss support surfaces are made to t standard hospital and health care facility beds. However,

variations in bed rail dimensions, mattress compression based on patient size and shape, conditions

such as dementia, seizure disorders, sleeping problems, incontinence, and restlessness could create an

entrapment risk. Proper patient assessment and monitoring, and equipment use and maintenance are

required to reduce entrapment risk.

Figure A

Step 1

Place the mattress at on the bed frame. The ination tube should be towards the foot end so that it

can be connected to the ination nozzles on the control unit.

Step 2

You may place a thin cotton sheet over the quilted mattress top cover.

Step 3

Hang the control unit over the frame or board at the foot end of the bed using the hooks attached to

the control unit. Make sure the control unit is secured.

Step 4

Connect the ination tubes from the mattress to the control unit’s inating nozzles. Make sure they

are properly attached.

NOTE!

Make sure the air hoses are not kinked or tucked under the mattress. Also check to ensure the

CPR valves are properly attached.

NOTE!

Before inserting the plug into the outlet, make sure the voltage is compatible.

Step 5

Switch the power switch on the side of the control unit on. The mattress replacement system may

take up to 40 minutes for full ination. For rapid ination an external pump may be used such as

Drive’s electric quick ll pump, item #: 14427QF.

Proceed to the Operating Instructions section on page 7.

INSTALLATION INSTRUCTIONS

OPERATING INSTRUCTIONS

Step 1

Turn on the control unit power. The indicator of the power switch will come on. The control unit will start

to blow air into the mattress.

Step 2

The Low Pressure indicator (orange) will come on as ination is underway.

Step 3

Press the Static button for a quicker ination.

Step 4

When the pressure reaches the preset level, within approximately 30 minutes, the Normal Pressure

indicator will come on, and the Low Pressure indicator will turn off.

Step 5

Patients can directly lie on the mattress or cover with a sheet and tuck loosely to increase the comfort

of the patient.

Step 6

Determine the patient’s weight and set the control knob to that weight setting on the control unit.

Step 7

Press the Static button to shift between Alternating mode and Static Mode. When in Static mode, and

the Static indicator will come on. The static mode will be started within approximately 6 minutes. In

Alternating Pressure mode, the air cells will alternate in 10 min cycles.

NOTE!

In static mode, the mattress provides a rm surface that makes it easier for the patient to transfer or

reposition. The static mode will help ensure the patient does not bottom out when in a sitting position.

DISCONNECT DEVICE

To fully disengage the power to the unit, disconnect the power cord from the AC inlet.

WARNING

• The control unit provided should only be used with the air mattress provided.

• Do not expose the product to lint, dust and sun light to prevent damage of the product.

• Keep the product away from the heat and moisture.

• Keep the product away from pets and children.

ENVIRONMENT REQUIREMENTS

• Operation Temperature: 50℉~95℉ (10℃~35℃)

• Storage and Transport Temperature: 5℉~122℉ (-15℃~50℃)

• Operation Humidity: 20%~80% non-condensing

CLEANING GUIDELINES

• Use a neutral detergent to clean surface of control unit and mattress; disinfectant products may be

used according to the manufacturer’s protocol. Do not use phenolics on this product.

• Do not immerse the control unit in water.

• Do not heat or steam in autoclave.

• Be sure to fully air dry the mattress and cover after cleaning and before use.

• After using for some time (~ 3 months), clean the air lter cotton inside the enclosure base, steps as

below:

1) Take out air lter cover and air lter cotton.

2) Wash air lter cotton with clean water, if the dirt sticks to the lter, soak the air lter cotton in the

water.

3) Dry the air lter cotton then put it back to the air lter cover.

MAINTENANCE

• Make sure the control unit is in good condition by checking if the indicators illuminate when the

power is rst turned on.

• Power supply cord can be replaced by SERVICE PERSONNEL.

Power supply Information: Non-detachable cord , 18AWG/2C, Rated 300V, 105℃.

WARNING

For safety reasons, only qualied service personnel should open the equipment.

MANUFACTURER will provide circuit diagrams, component part lists, descriptions, calibration

instructions to assist to SERVICE PERSONNEL in parts repair.

LAY OPERATOR or LAY RESPONSIBLE ORGANIZATION should contact the MANUFACTURER or the

MANUFACTURER’S representative for assistance in setting up, using or maintaining the product and

to report unexpected operation or events.

MAINTENANCE TROUBLE SHOOT / TECHNICAL SPECIFICATIONS

Trouble Signal Failure Cause Fault Handling

No air output

Power indicator

is ON.

The inflation tube is not con-

nected to the control unit. Connect the air tube.

The silicone tubes inside the

control unit are disconnected. Contact Service Personnel.

Power indicator

is OFF.No power.Turn on power switch

Incomplete inflation Mattress too soft.

Small hole at the air cell, or

mattress life comes to its end.

Replace the air cell or

the whole mattress.

Air knob indicate at “MIN”

location.

Turn the air tube at the

right to give max pressure .

PACKAGE CONTENT LIST

• Control Unit x 1 • Mattress Unit x 1 • User Manual x 1

TECHNICAL SPECIFICATIONS

INPUT RATING: 120VAC, 60Hz, 1A FUSE RATING: 250V, 1A

Control Unit Mattress

Item #: Melody 14026P Item #: 14026M

Power Supply: 120V/60Hz Size: 80’’L x 35’’W x 8’’H

Air output: 8 liter/min Top Cover Material: Nylon/PU

Pressure range: 30-60 mmHg Air Cells Material: Nylon/PVC

Cycle Time: 10 min Bottom cover material: Nylon/PVC

Size: 11’’ x 5.9’’ x 3.5’’ # of aircells: 20

Weight: 1.4kg (3lbs) CPR Valve? YES

LIMITED WARRANTY

Your Drive branded product is warranted to be free of defects in materials and workmanship

for 1 year from the date of purchase for the original consumer purchaser.

This device was built to exacting standards and carefully inspected prior to shipment. This

Limited 1 Year Warranty is an expression of our confidence in the materials and workmanship

of our products and our assurance to the consumer of years of dependable service.

This warranty does not cover device failure due to owner misuse or negligence, or normal

wear and tear. The warranty does not extend to non-durable components, such as rubber

accessories, casters, and grips, which are subject to normal wear and need periodic

replacement.

If you have any questions about your Drive device or this warranty, please contact an

authorized Drive dealer.

Inhaltsverzeichnis

Andere Drive Medizinische Geräte Handbücher

Drive

Drive RTL11148KDR Bedienungsanleitung

Drive

Drive DeVilbiss Med Aire DuoWave Bedienungsanleitung

Drive

Drive 14508 Bedienungsanleitung

Drive

Drive OXYMIZER Bedienungsanleitung

Drive

Drive AIRIAL CHAMBER Bedienungsanleitung

Drive

Drive DeVilbiss Healthcare Vacu-Aide 7325 Series Handbuch

Drive

Drive RTL12087 Bedienungsanleitung

Drive

Drive DSF 130 Bedienungsanleitung

Drive

Drive 15561 Bedienungsanleitung

Drive

Drive 13069 Bedienungsanleitung

Drive

Drive Inspired Poziform P-AP100XS Montageanleitung

Drive

Drive 13239D Bedienungsanleitung

Drive

Drive DeVilbiss iGo2 125 Bedienungsanleitung

Drive

Drive Aquajoy Premier Plus Bedienungsanleitung

Drive

Drive 15005L Montageanleitung

Drive

Drive 15300 Bedienungsanleitung

Drive

Drive Mountway Neptune Toilet lift Bedienungsanleitung

Drive

Drive VacuMax 18610 Handbuch

Drive

Drive SmartDose CTOX-MN02 Bedienungsanleitung

Drive

Drive PreserveTech LS9500N Bedienungsanleitung

Drive

Drive MEDQUIP MQ3200 Bedienungsanleitung

Drive

Drive 12036 Bedienungsanleitung

Drive

Drive Evolution OM-900 Bedienungsanleitung

Drive

Drive Med Aire Plus 10" Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung