Durafly EXCALIBUR Bedienungsanleitung
Please read this manual carefully
before operating this plane.
Instruction manual
CONTENTS
Specifications 1
Introduction 1
Contents Of Box 2
Required To Complete Model 2
Optional Parts 2
Assembly (PNF) 3-6
Setting Up Your Model 7-8
Additional Parts Included 9-10
Model Flying Precautions 11
Pre-flight Checks 11
Flying the Excalibur 12
Excalibur Tips 13
Spare Parts Listing 14
Trouble Shooting 15
Useful Links and Notes 16
Wing span:1600mm(63.5”)
Length:1010mm(40.2”)
Flying weight:1250g(44.2oz)
Controls:4 Channel (Ailerons,Elevator,Rudder (V-Tail),Throttle)
ESC: Aerostar 60amp Brushless ESC
Motor:3542 800kv Brushless outrunner
Prop: Aerostar Folding Carbon 13x7
Battery:1800-2200mAh, 4S lipo, 40-65C
Radio system: Minimum 4 channel Rx and Tx required
Servos: 4 x 9g high torque
_
_
_
_
_
_
_
_
_
_
Forged by Kings in a distant realm, the legendary Excalibur is here!
The Excalibur is the perfect marriage of modern design and materials, with rock solid engineering
and performance. The entire model features carefully positioned carbon and glass fibre
reinforcement through-out, super smooth EPO foam for the lowest drag possible, quick connect
PCB wing plugs, efficient ball links on all surfaces and a simple screw together assembly.
This, is all wrapped up in the sleekest looking warmliner to date. The Excalibur's forward swept wing
and V-tail design coupled with the mighty pre-install high torque power system, impresses on every
single level. And it is these lasting impressions from which legends are born.
Whether on the slope or at the field, rule the sky with the Durafly Excalibur.
1
INTRODUCTION:
SPECIFICATIONS:
1. Main wing panels
2. Fuselage
3. V-tail stabilizer
REQUIRED TO COMPLETE MODEL:
OrangeRx T-SIX 2.4GHz 6CH
Programmable Tx:
Part No. 9403000001 Mode 1
9403000002 Mode 2
OrangeRX R620X
6Ch 2.4Ghz:
Part No. 9171000757-0
Turnigy Graphene 1800mah
65C 4S Lipo:
Part No. 9067000133-0
A-SPEC G2 2200mah
65C 4S Lipo:
Part No. 9472000004-0
1
2
3
4
7
5
6
In its ‘Plug n Fly’ format the Excalibur will still require some additional electronic components to get
it ‘flight ready’. Durafly recommends the products below for optimum performance and great value.
Available at hobbyking.com. If you are viewing this manual online, click
7. Upper tail plate
8. Slope nose cone
9. Wing spars
4. Control & mounting accessories
5. Prop and spinner assembly
6. Fuselage patch kit plates
8
10. Canopy/hatch
9
10
OPTIONAL PARTS:
To further extend the Excalibur's performance and versatility, the below optional parts are available
directly from Hobbyking.com The ‘Pro prop’ upgrade is for those more experienced pilots that are
looking to squeeze the maximum performance out of the stock set-up and can be purchased
directly from the site. The ‘FPV canopy hatch’ is a free to download 3D file of the canopy from the
files tab of the listing for those that with to 3D print their own canopy and FPV the Excalibur.
2
CONTENT:
B.
2.3x6mm
1. Out of the box your Excalibur comes with reinforced foam hinges. However before assembly can
begin, each hinge line must be flexed back and forth 5-6 times to reduce tension and load on the
servo. Do this for all control surfaces before continuing.
Test and center each tail servo then carefully install each tail half into the the housing at the
rear of the fuselage. Connect the servos to the extension leads and ensure they are pushed
forward into the fuselage when fitting the tail, for the perfect fit as shown (A). With the tail now
correctly in place, add the top tail mounting plate and secure using the supplied 2.3x6mm screws
(B). Turn the tail over and repeat this process (C). Finally locate and install the tail servo horns and
control rods (D).
Note:
- For max strength and security, UHU glue can be used in addition to supplied screws when installing the tail.
- When connecting ball links, the side with the ring molded on, is the side pressed onto the ball.
- Use of heat shrink or sticky tape is recommended to keep the extension/servo lead connection secure.
A.
FPV canopy 3D file for printing. Download for free
here.
‘Pro’ proppeller. 13 x 8 Full carbon folder
SKU: 445000071-0
3
2.
B.
A.
2.3x6mm
C.
Center the aileron servo’s and connect the ball link to the ball end on each control horn using the
push clip to secure the rod to the servo horn as show (A,B). Screw or unscrew the ball link as
required to get the aileron level with the wing trailing edge with the servo center.
A.
4
B.
3.
Push the supplied carbon wing joining spars into the slots of the fuselage (A), longer at the front,
shorter at the rear, ensuring neither catch on any wires when passing through the fuselage. Once
inserted, ensure both are centered as show (B).
4.
D.
5
3x20mm
A.
2.3x6mm
2.3x6mm
B.
B.
Note:
- For increased performance, we suggest the optional 13x8 ‘Pro’ propeller blades. See page 2/3
-The propellers should be balanced out of the box, however it is recommended a final balance check be carried
out before attaching to the model. A well balanced prop will greatly increase all round performance and
efficiency of the model in flight.
Maintaining their aligned position, slide one wing panel onto the spars and into place on the
fuselage. Handle with care, as you may need a good firm push to get the wing fully into position.
Repeat with the remaining panel (A). With both panels firmly in place, secure with four of the
2.3x6mm screws as shown (B).
5.
Bolt each prop blade to the hub using the supplied 3x20mm bolts and lock nuts. Do not over
tighten these bolts, the blade should be able to freely fold back (A). Now secure the prop and hub
onto the prop adapter and tighten the entire assembly onto the motor shaft and finish off by
screwing the spinner in place with the final 2.3x6mm screws (B).
6.
The final stage of assembly is to install your choice of 4-6ch receiver, the smaller the better. With
all servo leads connected, the receiver can be inserted under the wing leading edge and secured
with if desired. Your 1800-2200mah 4S lipo (2200mah 4S ASPEC G2 shown) installs as seen below.
This is also the desired location for correct CG.
7.
A.
6
Congratulations, basic assembly of your Excalibur is now complete.
Please perform a final check on all screws, bolts and
components, ensuring all are secure
and firmly in place.
7
SETTING UP YOUR MODEL:
Inhaltsverzeichnis
Andere Durafly Spielzeug Handbücher
Durafly
Durafly ME-163 Bedienungsanleitung
Durafly
Durafly Micro Tundra PNF Bedienungsanleitung
Durafly
Durafly Bonanza Bedienungsanleitung
Durafly
Durafly T-28 TROJAN Bedienungsanleitung
Durafly
Durafly Curtiss P-40N Bedienungsanleitung
Durafly
Durafly Ugly Stick Bedienungsanleitung
Durafly
Durafly GLOSTER GLADIATOR MK1 Bedienungsanleitung
Durafly
Durafly Retro Series Junior models Plug and Fly Bedienungsanleitung
Durafly
Durafly Auto-G2V2 Bedienungsanleitung
Durafly
Durafly PRIME TUNDRA Bedienungsanleitung
Durafly
Durafly GOBLIN Bedienungsanleitung
Durafly
Durafly ME-163 V2 Bedienungsanleitung
Durafly
Durafly BF-110 Stücklistenhandbuch
Durafly
Durafly SlowPoke Bedienungsanleitung
Durafly
Durafly Messerschmitt BF.109E-4 Bedienungsanleitung
Durafly
Durafly BRAVADO Bedienungsanleitung
Durafly
Durafly Das Ugly Stik Bedienungsanleitung
Durafly
Durafly ZEPHYR V-70 EDF-EPO Bedienungsanleitung
Durafly
Durafly TUNDRA V2 Bedienungsanleitung
Durafly
Durafly EFXTRA Bedienungsanleitung
