Duratuf MK3B Bedienungsanleitung

Quality –Built In

ASSEMBLY INSTRUCTIONS

MK3B

BASE SIZE 3380mm x 3380mm

 Drill

 Drill Bit 3.5mm

 Drill Bit 6mm (for clear roof panel only)

 Riveter

 Hammer

 Nail Punch

 Tape Measure

 Ladder or Saw stool

 Spanners x 2

 String Line

 Tin Snips

 Skillsaw and Jigsaw (for floor only)

 Masonry Drill and 10mm Masonry Bit (for Bolt Down Kit only)

 Read all instructions carefully.

 Identify all parts and check quantities against checklist.

 If you are making your own floor refer to Raised Base Plate section

now.

 Do not attempt to build your shed in high winds.

 Beware of sharp edges.

 Protect your eyes and ears.

 Use electric tools with care. Use a Safety Trip Switch.

 It is easier and quicker if this shed is erected by two people.

 Your shed must be level. Achieve this by either levelling the ground

or by using blocks.

 If you shed is to be positioned on wet or damp ground, we recom-

mend that your shed is raised up off the ground slightly.

Tools Required:

Select your site:

Safety:

Before you start:

ASSEMBLY INSTRUCTIONS

2.280m

1.890m

0.260m

Gable End Wall Sheets

Wall Sheets

Door - Standard Security

Instruction Booklet

Hardware Pack

Touch-up Paint & Brush

0.580m

0.603 x 0.603m

0.588 x 0.150m

Fixed Window Frame

Glaze Beads

Glass

Louvre Window Frame

Glass

Window Hardware Pack

3.700m Roof Sheets

Security Double Door Hardware Pack

Alarm - MA20

Shed light

Bolt Down Kit

Peg Down Kit

1.825m Flat Roof Sheet

Jack Studs - 140 x 45mm

Roof Sheets

1.825m Clear Roof Panel

0.350m Pressed Capping Sheet

0.900m Bevel Edge Support 45 x 45mm

Clear Roof Hardware Pack

43.700m

130m

Jack Studs - 60 x 45mm

Centre Door Stop

Strip Bracing

0.200m

1. Bottom Side Plates x 2

2. Bottom Front/Rear Plates x 2

3. Top Side Plates x 2

4. Top Front/Rear Plates x 2

5. Studs x15

6. Ridge Beam x 3

7. Nogs x 14

8. Jack Studs (250 x 140 x 45) x 2

9. Jack Studs (200 x 55 x 45) x 4

10. Roof Nogs x 16

CONSTRUCTION DETAILS DRAWN: DWG.NO:125 © All Images protected by Copyright.

MARK 3 B KIWI GARDEN SHED DATE: 16/12/98 SHEET:6 All information remains exclusive

(3380 x 3380—11.42m³)SCALE: 1:33 A3 ISS:D property of Riverlea Industries Ltd.

END ELEVATION SHOWING STRAP

BRACING TOP OF RIDGE BEAM TO

UNDERSIDE OF TOP SIDE PLATE

STRAP BRACING (to all

jack studs under beams)

MULTI-GRIP FASTENERS

EACH CORNER (ALL

HOLES NAILED OFF)

DYNABOLTS OR AP-

PROVED FIXINGS 100MM

FROM OUTSIDE CORNER

THEN ON 1200 C

PRYDA STRAP

BRACING, 5 NAILS

PER END

WHERE FLOOR IS TIMBER

FRAMED, SECURE STUDS AT

EACH CORNER TO A CORNER

NCHOR PILE WITH A 6 KN CON-

NECTOR

3380

70 45 45 45 70

765

765 787 787

785 785

1630

45 45 45 45

45 45 45 45 45

789

140 x 45 Ridge Beam

140 x 45 Intermediate Roof Beam

140 x 45 Intermediate

PLAN

140 x 45 Ridge Beam

140 x 45 Intermediate Ridge Beam

400 1900

883

3380

FRONT ELEVATION

1900

3380

END ELEVATION

MK3B TIMBER FRAME

Step 1: Back Wall: Select one 3.380m Base Plate (Green), one

3.380m Top Plate (Red) and five Studs (Yellow). Lay out

Plates and two Studs on a flat surface and nail together us-

ing two 75mm nails per join. Nail in remaining centre studs

using Nogs to get correct position. Position Nogs .883m

below Top Plate and nail in place. (All Plates, Studs and

Nogs are joined together with two 75mm nails each end).

Step 2: Front Wall: Select one 3.380m Base Plate (Green), one

3.380m Top Plate (Red), four Studs (Yellow) and

two .785m Nogs. Nail studs to each end of Plates. Nail in

remaining two studs using .785m Nogs to get correct po-

sition. Position Nogs .883m below Top Plate and nail in

place.

Step 3: End Wall: Select one 3.380m Base Plate (Green), one

3.380m Top Plate (Red), three Studs (Yellow) and

two .787m Nogs. Lay out Plates and one Stud on a flat

surface and nail Stud centrally between Plates. Nail re-

maining Studs to Plates using .787m Nogs to get the cor-

rect position. Position Nogs .883m below Top Plate and

nail in place. Repeat with second End Frame.

JACK STUDS

YELLOW

Note: For sheds with the Raised Floor Modification option the studs will be 1.780m long to allow the Wall Sheets to pro-

trude 20mm below the Bottom Plate. Refer to Raised Floor Modification section (Page 15).

MK3B TIMBER FRAME

Step 4: Stand up Back Wall frame and one End frame

and nail together, using two 75mm nails per join,

top and bottom. Stand remaining Frames up and

nail together. Nail in remaining .765m Nogs in

End Walls.

Step 5: Position middle Jack Stud, centrally on End Wall

Top Plates and nail in place. Nail remaining Jack

Studs in. Position middle Ridge Beam to Jack

Stud and skew-nail in place using two 75mm

nails each end. Pre-drilling holes before nailing

will prevent timber from splitting.

Step 6: Place intermediate Roof Beams by using Roofing

Nogs to determine correct position (see fig. 2).

Nail intermediate Roof Beams in place. Nail 70 x

45mm Roofing Nogs in place (End Wall) and 90

x 45mm Roofing Nogs in place (Middle).

Step 7: Place Frame in correct position, checking the shed is square and level.

Dynabolt Frame to concrete base as instructed on page 4.

Step 8: Temporarily brace each side and roof, making sure each side is square.

Nail strip bracing to outside of Frame (see page 4), making sure it is tight.

Nail multigrip brackets to each of the four bottom corners (two per cor-

ner). Use 30mm bracket nails supplied.

Note: Condensation can form on the underside of cladding. If building paper is required, fit now. The building paper

will need to be supported by netting or roofing twine.

fig.2.

MK3B WALL CLADDING

TO AVIOD CORROSION:

 Where at all possible try not to trap metal filings between two sheets. Remove all metal filings before riveting.

 Carbon in pencils reacts with the Zinc/Aluminium coating on steel. Use ink to mark steel.

TERMS EXPLANATION

 To Tack: To Tack on a wall sheet means to use minimum nails hammered partly in to hold Wall Sheets in position. Should

a Wall Sheet need to be re-positioned, the nails can easily be prized out.

 If a window is required, identify Wall Sheet(s) with window hole pre-cut. Lean up Wall Sheets where window(s) are to be located.

Note:

When fitting Gable

End Sheets ensure

they overlap correctly

(fig 1).

The overlap direction

may differ from clad-

ding detail.

CLADDING DETAIL

Birds Eye View

fig. 1

MK3B WALL CLADDING

Step 1: Front Wall: Start at the left hand side. Posi-

tion the Wall Sheet with the LIP on the left hand

side. Ensuring the LIP is flush with side of the

Stud and the top of the Top Plate, tack in place.

Repeat with Wall Sheet on the right hand side

of doorway.

Step 2: Back Wall: Position the first Wall Sheet with

the LIP on the right hand side. Ensuring the LIP

is flush with the side of the Stud and the top of

the Wall Sheet is flush with the top of the Top

Plate, tack in place. Position the next Wall

Sheet with the LIP on the right hand side. Over-

lap as shown in fig.1 (page 7). Ensuring Wall

Sheet is flush with top of Top Plate, tack in

place. Repeat with remaining two sheets.

Step 4: Nailing Off: Nail one 30mm Clout each side of the Rib (two per Pan) into the Top Plates and Bottom

Plates. Nail Wall Sheets to mid wall Nogs (one per pan). Nail each corner Wall Sheet to Studs using two

30mm Clouts evenly spaced.

Gable Ends: When nailing Gable Wall Sheets to the Top Plate, use a String Line. At the top of the gable nail two

30mm Clouts into the end of the Ridge Beam. This will stop it from twisting.

Step 3: End Walls: Lean Gable Wall Sheets against

the shed to form gable shape. With the LIP

flush with side of Stud tack in place ensuring

the bottom of the Wall Sheet is 10mm above

the bottom of the Bottom Plate. Tack on re-

maining Wall Sheets. Repeat with other gable

end. If fitting a window, nail in Window Studs

and Nog now. Refer to Window instructions.

EDGE

FLUSH

TOP

FLUSH

MK3B LOUVRE WINDOW (Optional)

Step 2: On the inside of the shed, position studs

and Nog centrally on window opening.

Make sure the studs are parallel and nail

into Top Plate and end wall Nog.

Step 3: Nail wall Sheets to window framing using

30mm clouts. (return to step 4 on page 7

and complete). Then fit Window Frame).

Position Window Frame centrally on win-

dow opening and rivet it to ribs. Pre-drill

holes in each corner and nail Window

Frame to framing, using 50mm nails.

Step 4: If the Window is in the gable end, tempo-

rarily position the Over Panel above Win-

dow Frame. Following the same angle as

the gable, mark and cut to suit.

Step 5: Rivet Over Panel to the Window Frame

with rivets.

588mm

Step 1: Lay out the two window studs (883mm) and

Nog (634mm) on a flat surface. Position

Nog and nail in place using 2x 75mm nails

at each end.

Step 6: From the inside of the shed, slide Louvre

Glass into Louvre Units attached to the

Window Frame. Bend up tabs to keep

Glass in position.

50mm

NAILS

RIVITS

Step1: Fit Door Jamb Flashing (A104) in be-

tween Top and Bottom Plates and hard

against Stud. Attach Door Jamb Flash-

ing with three 30mm clouts into studs on

the inside and three rivets into Rib on

the outside. Pre-drill holes on the outside

to protect flashing. Repeat with the other

Door Jamb.

Step2: Measure and cut Doorstep Flashing (A106)

to fit in between Door Jambs. Positioning

the Doorstep Flashing in between Door

Jambs at bottom of doorway, nail through

top of flashing using five 30mm Clouts. Re-

peat with the Overdoor Flashing (A105).

Step 1: Lay out the two window studs (883mm) and

Nog (590mm) on a flat surface. Position

Nog and nail in place using two 75mm nails

at each end.

570mm

Step 6: From the outside of the shed, place glass

in Window Frame. Attach a Glazing Bead

(G100) with three rivets to each side of the

Window Frame to hold glass in place. Pre-

drilling Glazing Beads is recommended.

MK3B FIXED WINDOW (Optional)

Follow Steps 2 - 5 on page 8.

MK3B DOOR JAMB & CORNER FLASHINGS

Inhaltsverzeichnis

Andere Duratuf Außenlagerung Handbücher

Duratuf

Duratuf TUF 400 Bedienungsanleitung

Duratuf

Duratuf PG99 Bedienungsanleitung

Duratuf

Duratuf Paihia Bedienungsanleitung

Duratuf

Duratuf PL43 Bedienungsanleitung

Duratuf

Duratuf Sentry Sheds SL1515 Bedienungsanleitung

Duratuf

Duratuf Smart store SS1507 Bedienungsanleitung

Duratuf

Duratuf GL95 Bedienungsanleitung

Duratuf

Duratuf GL65 Bedienungsanleitung

Duratuf

Duratuf TUF LOCKER Bedienungsanleitung

Duratuf

Duratuf Havelock Bedienungsanleitung

Duratuf

Duratuf Guardian Sheds GS73 Bedienungsanleitung

Duratuf

Duratuf SL3015 Bedienungsanleitung

Duratuf

Duratuf SG3025 Bedienungsanleitung

Duratuf

Duratuf GL105 Bedienungsanleitung

Duratuf

Duratuf GG109 Bedienungsanleitung

Duratuf

Duratuf PL46 Bedienungsanleitung

Duratuf

Duratuf GG97 Bedienungsanleitung

Duratuf

Duratuf KAIPARA Bedienungsanleitung

Duratuf

Duratuf Sentry Shed SL1507 Bedienungsanleitung

Duratuf

Duratuf SS1510 Bedienungsanleitung

Duratuf

Duratuf Garrison PL36 Bedienungsanleitung

Duratuf

Duratuf GL57 Bedienungsanleitung

Duratuf

Duratuf SL1020 Bedienungsanleitung

Duratuf

Duratuf GS72 Bedienungsanleitung

Beliebte Außenlagerung Handbücher anderer Marken

USP

USP DURAMAX 10 Ft x 8 Ft StoreMax Plus Bedienungsanleitung

TYGO

TYGO Nyland Bedienungsanleitung

Viking

Viking SD5300SS Technisches Handbuch

USP

USP DURAMAX Apex Pro 10.5 Ft x 8 Ft 40116 Bedienungsanleitung

ModuLaro

ModuLaro Lojo WC202200 Bedienungsanleitung

Lifetime

Lifetime 6418 Bedienungsanleitung

rollaway container

rollaway container ARPCA24 Bedienungsanleitung

X-METAL

X-METAL 4065 Bedienungsanleitung

Outdoor Life Products

Outdoor Life Products FP2030 F Bedienungsanleitung

Royalcraft

Royalcraft Faro 295L Storage Box Bedienungsanleitung

Riverlea

Riverlea Duratuf KIWI KS3 Bedienungsanleitung

Rubbermaid

Rubbermaid 5L45 Bedienungsanleitung

garofalo

garofalo TUSCANY EVO Bedienungsanleitung

OLT

OLT GS84D-FJ-Plywood Bedienungsanleitung

Eden

Eden CA2988 Bedienungsanleitung

Palram

Palram CANOPIA RUBICON 6x10 Administratorhandbuch

Suncast

Suncast 774098 Bedienungsanleitung

Lifetime

Lifetime 60186 Bedienungsanleitung