Dyson Micro Bedienungsanleitung

User manual

SV33 JN.00000 PN.000000-00-00

00.00.00 VERSION NO.01

Contents

In the box

Getting started

Caring for your floors

Charging your machine

Emptying your bin

Cleaning your bin

Clearing blockages

Clearing blockages from your

Hair screw tool

Washing your filter

Washing your Illuminated cleaner

head brush bar

Cleaning your tools

Looking after your machine

The Dyson cordless

vacuum cleaner in an

upright position with

the wand and cleaner

head attached.

Dyson micro logo

In the box

Vacuum cleaner Charger

Wand

Combi-crevice tool

Charges your vacuum with

or without a dock.

Worktop tool

Engineered for

cleaning kitchen

worktops, tables

and hard surfaces.

Two tools in one –

narrow nozzle and

brush, for quick

switching between

cleaning and

dusting tasks.

Wand clip

Clips to your vacuum's

wand to hold tools.

Your Dyson vacuum drops into the

aluminium dock, so it’s easy to store

anywhere you choose, with no need

to fix to the wall.

Hair screw tool

Anti-tangle conical

brush bar spirals hair

off and into the bin.

Motor-driven cleaning

for smaller spaces.

Light pipe crevice tool

Crevice tool with LED

lights lets you reach

into dark, narrow

spaces and see where

you’re cleaning.

The illuminated cleaner

head makes invisible

dust visible on hard floors.

Dyson Floor Dok

Illuminated

cleaner head

Dyson Floor Dok only available on selected models.

Wall dock

The Dyson cordless vacuum drops

into the wall-mounted charging dock,

ready for your next clean.

Some tools may not be included, small details may vary from those shown.

You

can buy additional tools at www.dyson.com.sg.Main body showing the handle

and bin attached.

The narrow connector end at the top, this connects

to the bin and the wider end at the bottom that

connects to the cleaner head or tool.

The charger is a

one piece unit with

the plug, connector

end and cable.

This tool has

a combina-

tion of brush

head and

crevice tool

together in

one unit. The

brush head

slides down

the crevice

tool when

needed.

This tool is angled and

has a nozzle end.

A plastic clip that

attaches to the wand

A floor standing dock

with a round base

and a cylindrical

support with the

support for your ma-

chine at the top. Slide

the battery section

of your machine into

the dock where it

then connects to the

charging points.

A long tool with

an angled end.

A soft fluffy brush bar

housed within the

cleaner head. There is

an electrical connecter

end that can attach to

the end of the wand or

directly to the machine.

A rectangular

dock that

needs to be

fixed to a wall

with screws.

A small cleaner head

with an angled body

housing the motor and

an electrical connector

to attach to the wand or

directly to the machine.

Power button

Press the Power button

once for comfortable,

continuous cleaning.

We’ve removed the

trigger, so you can

swap hands easily while

cleaning around obstacles

Press the button to change

power modes.

Power modes

Eco mode

Max mode

The optimum balance of

power and run time

Delivers maximum power.

For intensive cleaning of

ground-in dirt.

The illuminated cleaner

head makes invisible

dust visible on hard floors.

Illuminated cleaner head

Small details may vary from those shown.

Getting started

Location of the power

button on the top of the

machine.

Pointers to demonstrate

that the tools can be

connected directly to the

main body or to the end of

the wand.

Arrow showing the end

of the wand connecting

to the cleaner head.

The main body of the

Dyson vacuum connects

to the illuminated cleaner

head floor tool.

The main body with

the power button and

mode button on the

top of the machine and

bin with the bin base

closed.

The connection of the wand

onto the main body, with the

wand release button aligned

with the buttons on the

handle of the main body.

Charging your machine

For the best experience, we recommend fully charging your machine, and

any additional batteries, as soon as you open the box and after every clean.

The LED light on the end of the handle will flash when the power is running

low and you need to put your battery on to charge.

Connect the charger directly to the charging point on the base of the

handle of your machine. You can also connect to your dock as shown in the

installation instructions supplied with your dock.

The LED light on the end of the handle will pulse with a blue LED light when

charging, and the light will go out when fully charged.

It can take up to 3.5 hours to fully charge your battery. Your battery has been

designed to be left on charge.

Your machine won’t operate or charge if the ambient temperature is below

5°C (41°F). This is designed to protect both the motor and battery.

You can help prolong the battery life by leaving your machine to cool down

before recharging.

Caring for your floors

Check that the underside of the cleaner head or tool is clean and free from

any objects that may cause damage.

Before vacuuming your flooring, rugs, and carpets, check the manufacturer’s

recommended cleaning instructions.

This machine is designed for use on hard floors. The brush bar on your

machine can damage certain flooring. Some rug materials may fuzz if a

rotating brush bar is used when vacuuming. If this happens, we recommend

vacuuming without the motorised floor tool and consulting with your flooring

manufacturer.

The charger connected from

the power supply directly into

the front of the battery.

Emptying your bin

Empty your bin as soon as the dirt reaches the MAX mark.

You may need to clean the filter more often if you use your machine with a full bin.

Cleaning your bin

Release the dirt

To remove the bin for emptying:

Minimise dust contact

Replace your bin

Remove your wand

Don’t put any part of your machine in a dishwasher or use detergents,

polishes or air fresheners.

Hold the machine over the bin, pointing downwards.

Firmly push the red bin release button. The bin will slide down, cleaning the

shroud as it goes, and the bin base will open.

The bin base won’t open if the red bin release button isn’t pushed down all

the way.

If the bin doesn't empty fully, remove the bin and empty the dirt.

Press the red button located on the bin runner to release the bin and slide

your bin off the runner.

Cover your bin tightly in a dust proof bag while you empty. Remove your bin

carefully, seal the bag tightly and dispose.

If you have removed your bin, slide it back on to the runner. Make sure that

the bin and lid are both securely in position.

Push the bin base upwards until the bin and lid both click into place.

Reconnect the wand.

Press the red wand release button, on the top of the wand, and pull the wand

away from the bin.

clik

Clean your bin

Replace your bin

Insert the spine on to the bin runner.

Close your bin by pushing the bin base upwards until the bin and bin base

click into place.

Close the bin

Push the bin base upwards until your bin and bin base click into place.

If it is necessary to clean your bin, empty it as shown in the ‘Emptying your bin’ section.

Press the red button located on the bin runner to release the bin and slide your bin off

the runner.

To clean your bin, you can use a damp, lint-free cloth, or run it under a stream of

water. Never fully submerge you bin under water. Once your bin is cleaned leave to

dry before reattaching.

Make sure that your bin and seals are completely dry before replacing.

The MAX mark on the bin of

the machine, showing that

the dirt should not be filled

over the Max mark when the

machine is at the angle of

normal use.

Illustration of

the bin being

emptied into

a bag.

Two images of the bin with arrows

showing the bin lid closing and

a click symbol and the bin being

pushed upwards with another

click symbol.

The bin lid

closing with an

audible click and

the bin being

pushed upwards

with another

click once it is

fully in place.

The bin being

removed and the

location of the bin

release lever on the

underside of the

bin runner.

The bin being pushed

back into position on

the bin runner.

Illustration of the bin

being emptied.

Clearing blockages

If your machine detects a blockage, the motor will pulse six times. You

won’t be able to use your machine until the blockage has been cleared.

If you try to use your machine when the motor is pulsing, it will

automatically cut out.

Leave your machine to cool down before looking for blockages.

Disconnect your machine from the charger before looking for blockages.

Be aware of sharp objects.

Leave your machine to cool down before looking for blockages.

Don’t use your machine when looking for blockages as this could cause

injury.

With the wand

removed from

the machine,

check for

blockages at

both ends of

the wand.

Check for blockages in

the filter end and bin

ends of the machine.

With the bin removed,

check for blockages,

paying particular atten-

tion to the air inlet, locat-

ed at on the right–hand

side of the machine just

below the point where

the bin joins the main

body of the machine.

Turn the cleaner head over to

check for obstructions on the

brush bar and air inlet.

The bin being removed

and the location of the bin

release lever on the under-

side of the bin runner.

Remove any obstructions

from the brush bar.

Remove the cover and brush bar

Look for obstructions

Remove the Hair screw tool from the wand or machine.

Push the base plate open. Press the red lever down to release the cleaner

head cover.

Pull the cleaner head cover off the main body of the tool.

Pull your brush bar firmly to remove it from the main body.

Check and remove any obstructions from all three parts of your

Hair screw tool.

Your Hair screw tool isn't washable. Wipe over with a damp lint-free cloth.

Don’t put any part of your machine in a dishwasher or use detergents,

polishes or air fresheners.

Put your brush bar back into position and press firmly until it clicks back

into position.

Check the red locking lever is in the unlocked position. Align the cleaner

head cover with the guide on the main body. Push it down until it clicks into

position.

Push the red locking lever up until it clicks into position and push the base

plate back into place.

Clearing blockages from your

Hair screw tool

Your Hair screw tool doesn’t have a washable brush bar. To maintain

optimum performance, check your brush bar regularly and clear any

obstructions.

Make sure your machine is disconnected from the charger.

Reassemble Hair screw tool

Location of the lever

to release the brush

bar is located at

the back of the Hair

screw tool.

Slide the housing

back on to the

brush bar and

push the lever on

the back of the

Hair screw tool

upwards to lock.

Washing your filter

Wash your filter

Fill and shake

Shake out the water

Dry your filter

Tap your filter

Twist off your filter

For more information and support videos for your machine go

online: https://support.dyson.com.sg/SupportHome.aspxWash with warm, running tap water – gently rubbing your filter with your

fingers to remove the dirt.

Place your hand over one end of your filter.

Fill the filter with warm tap water.

Place your hand over the open end of the filter and shake it firmly to remove

trapped dirt and debris.

Repeat these steps until the water runs clear.

Empty the filter and shake firmly to remove excess water.

Shake with the filter in both an upward and downward position.

Keep shaking until there’s no water coming from the filter.

Don’t dry your filter in a tumble dryer, microwave or near a naked flame.

Important: your filter must be completely dry before you put it back into the

machine. Your machine could be damaged if used with a damp filter.

Before washing your filter, tap it gently over a bin to remove any loose dust

and debris.

Twist your filter anti-clockwise and pull it away from your machine.

Wash your filter at least once a month to maintain optimum suction power.

A hand holding the filter

with the narrow end

pointing downwards

with droplets of water

being shaken from the

filter and again, with the

end pointing downwards

shaking water out.

The filter is left to dry with the

pleated filter end facing upwards.

Filter with hand over the

open end with arrows

showing a shaking motion.

Filter held in upright

position, with the wider

end in the palm of a

hand. Water running

from a tap into the

narrower end.

The filter is located at the

rear of your machine.

Holding the filter

by the hard, plastic

end, tap the other

end over the bin.

Replace your brush bar

Remove your brush bar

Wash and dry your brush bar

Don’t put any part of your machine in a dishwasher or use detergents,

polishes or air fresheners.

Press the cleaner head release button on the end of the wand. Place the

cleaner head upside down.

Push the end cap up fully and pull the brush bar out of the cleaner head.

Remove the end cap from the brush bar. Don't wash the end cap.

Slide your brush bar out of the cleaner head.

Hold your brush bar under running water and gently rub to remove any lint

or dirt.

Stand your brush bar upright as shown. Leave to dry completely for at least

24 hours.

Before replacing, check that your brush bar is completely dry.

Reattach the end cap to your brush bar.

Slide your brush bar into the cleaner head. Push the end cap back down to

the closed position.

To maintain optimum performance, keep your optic lens clean. Only clean

the lens when the cleaner head is not attached to your machine.

Use a soft, dry, lint-free cloth to wipe the lens.

Cleaning your optic lens

Washing your Illuminated

cleaner head brush bar

Your Illuminated cleaner head has a washable brush bar. To maintain

optimum performance, check and wash your brush bar regularly.

Make sure your machine is disconnected from the charger.

The end cap should

be attached to the

cleaner head at an

angle less than 90°,

any angle greater

than this will not allow

the end cap to close.

The end cap is

located at the side

of the cleaner head.

Push this upwards to

unlock the brush bar.

Don't wash the end

cap.

The brush bar has

an open end and a

closed end. Stand

upright, with the

closed end facing

upwards, to dry.

Cleaning your tools

Don’t put any part of your machine in a dishwasher or use detergents,

polishes or air fresheners.

Wipe with a damp, lint-free cloth, without touching the connector end.

Make sure your tools are completely dry before using.

Combi-crevice tool Light pipe crevice tool Worktop tool

Hair screw tool

Small details may vary from those shown.

Inhaltsverzeichnis

Andere Dyson Staubsauger Handbücher

Dyson

Dyson DC37 Bedienungsanleitung

Dyson

Dyson DC21 Motorhead Bedienungsanleitung

Dyson

Dyson Ball DC25 Bedienungsanleitung

Dyson

Dyson DC29 Bedienungsanleitung

Dyson

Dyson V7 Motorhead Bedienungsanleitung

Dyson

Dyson DC22 Bedienungsanleitung

Dyson

Dyson V7 Motorhead Bedienungsanleitung

Dyson

Dyson CINETIC BIG BALL ABSOLUTE Bedienungsanleitung

Dyson

Dyson Outsize Bedienungsanleitung

Dyson

Dyson CINET BIG BALL Bedienungsanleitung

Dyson

Dyson V6 Absolute Bedienungsanleitung

Dyson

Dyson DC14 Telescope Reach Bedienungsanleitung

Dyson

Dyson DC14 Telescope Reach Bedienungsanleitung

Dyson

Dyson DCO5 Absolute Bedienungsanleitung

Dyson

Dyson DC24 Blueprint Limited Edition Bedienungsanleitung

Dyson

Dyson DC23 T2 Bedienungsanleitung

Dyson

Dyson DC02 Bedienungsanleitung

Dyson

Dyson 360 Eye Betriebsanleitung

Dyson

Dyson DC15 Bedienungsanleitung

Dyson

Dyson DC 16 Bedienungsanleitung

Dyson

Dyson DC31 Bedienungsanleitung

Dyson

Dyson Cinetic Big Ball Bedienungsanleitung

Dyson

Dyson Ball DC25 Bedienungsanleitung

Dyson

Dyson DC26 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Dyson micro Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken