Dyson V11 Bedienungsanleitung

User manual

SV12 JN.00000 PN.000000-00-00

00.00.00 VERSION NO.01

Contents

In the box

Getting started

The LCD screen

Caring for your floors

Charging your machine

Changing your click-in battery

Emptying your bin

Cleaning your bin

Clearing blockages

Clearing obstructions from your

MotorbarTM cleaner head

Clearing blockages from your

Hair screw tool

Washing your filter

Cleaning your tools

Looking after your machine

In the box

Some tools may not be included.

You can buy additional tools at www.dyson.com.au or www.dyson.co.nz

Combination tool Soft dusting brush

Extension hose Low-reach adaptor

Vacuum cleaner with

click-in battery

Crevice tool

Wand

Stubborn dirt brush

Hair screw tool

Light pipe crevice tool

Fabric and

mattress tool

Two tools in one –

wide nozzle and brush,

for quick switching

between cleaning and

dusting tasks around

your home or car.

Enclosed in a skirt

of soft nylon bristles

for gentle, vacuum-

assisted dusting of

delicate objects and

surfaces.

Adds up to 61cm of

flexible reach to any

tool attachment,

to clean up high or

down low in your

home or car.

Bends and locks at

different angles. Fits

any compatible tool

for effective cleaning

in hard-to-reach high

areas of your home.

Bends to comfortably

reach down low.

Engineered to clean

further under low

furniture by adjusting the

wand angle up to 90°.

Engineered for precise

cleaning around

tricky edges and into

hard-to-reach narrow

spaces.

Stiff nylon bristles

dislodge ground-in dirt

from coarse carpets,

high traffic areas and

car interiors.

Anti-tangle conical

brush bar spirals hair

off and into the bin.

Motor-driven cleaning

for smaller spaces.

Crevice tool with LED

lights lets you reach

into dark, narrow

spaces and see where

you’re cleaning.

Removes dust, dirt

and allergens from

mattresses and

upholstery.

Charger

Charges your vacuum with

or without a dock.

Wand clip

Clips to your vacuum's

wand to hold tools.

Wall dock

The Dyson cordless vacuum drops

into the wall-mounted charging dock,

ready for your next clean.

Up-top adaptor

Motorbar™cleaner head

De-tangling vanes

automatically clear

wrapped hair from the

brush bar as you clean.

Main body

showing the

handle and bin

attached.

A rectangular

dock that

needs to be

fixed to a wall

with screws.

The charger is a one

piece unit with the plug,

connector end and cable.

The narrow connector end at the top, this connects to the bin

and the wider end at the bottom that connects to the cleaner

head or tool.

This tool has a

combination

of brush head

and crevice tool

together in one

unit. The brush

head slides down

the crevice tool

when needed.

Pliable bristles

and felt bumper

strip on a narrow,

tapered tool.

A wide, triangular

shaped nozzle.

A plastic clip that

attaches to the wand

A long tool

with an

angled end.

With an elbow

joint, fitted

between the

bin and the

tool.

A small cleaner head

with an angled body

housing the motor and

an electrical connector

to attach to the wand or

directly to the machine.

A flexible hose

engineered from

tough wire and

durable plastic.

A short nozzle

with stiff

bristles on the

underside. A long tool with

an angled end.

Getting started

Eco

中文

한국어

Boost

中文

한국어

Power modes

Eco mode

Med mode

Boost mode

Your machine has three power modes for

different tasks. Change power modes quickly

using a single button.

Maximum run time for longer cleans all

around your home.

Designed for intensive spot cleaning

of ground–in dirt.

Med

The optimum balance of power and run time.

Diagram showing the connection of

the wand onto the main body, with

the wand release button aligned

with the top of the main body.

The screen showing the machine set to

Eco mode with a full battery in green

to show that this will give the longest

battery life of the three modes.

The screen showing the machine set

to Boost mode with a red battery to

show that this will give the shortest

battery life of the three modes.

Location of the Selection button

on the screen on the filter end

of the machine.

Arrow showing the end

of the wand connecting

to the cleaner head.

The screen showing the

machine set to med mode

with a blue battery showing

that this will give a medium

length of battery life.

The LCD screen

Settings menu

Change language

Change alert settings

To change the language on your screen, press the button and hold until the

language list appears. Release the button.

Tap the button to scroll through the language list to your preferred language.

Press and hold the button until the countdown ends.

A green tick will appear on the screen to show your language selection is

complete.

To cancel your selection, release the button during the countdown.

You can turn the alert motor pulse off. Your motor will no longer pulse but

run time alert information will continue to be displayed on the LCD screen

when your machine needs your attention.

Turning off alerts will not turn off the blockage alert pulsing. This is to ensure

you clear any blockages, preventing damage to your machine.

Tap to scroll through the settings menu. Select the ‘Alerts’ option.

Scroll to select on or off. Hold the button until the countdown ends and a tick

appears on the screen. To cancel your selection, release the button during

the countdown

English

Espanol

English

selected

Control the settings on your machine using the Selection button.

To enter the settings menu, press and hold the button until the menu screen

appears. Tap to scroll through the options available.

The LCD screen shows performance, including the cleaning mode selected,

remaining run time, filter maintenance and blockage information.

The Selection button

on the screen being

pressed.

Two screens, the first with

the language list and then

the tick screen to show that

the language has been

successfully changed.

The screen with an

amber warning

triangle to demon-

strate an alert.

Battery health

Run time countdown

To get the best performance and life from your battery, use Eco or Med mode.

When the battery needs charging, your machine will pulse three times and a

low run time icon will appear on the screen.

When your battery is empty, a red warning icon will appear on the screen.

4:50

Exit settings menu

The screen with a

battery time remaining

shown as a number and

as a half filled battery.

The battery health is

shown on the batter-

ies on the screen.

A red screen with an icon

with a plug being con-

nected to the power sup-

ply. This demonstrates

the battery is empty and

needs charging.

Screen with Exit

menu wording and

return icon.

If you have additional click-in batteries, we recommend that you alternate

the batteries to maintain even performance.

Additional click-in batteries available to purchase separately

Charging your machine

Connect to the charger either directly or in the dock.

The blue LEDs on either side of the battery will flash during charging.

When the battery is fully charged, both LEDs will light for 5 seconds.

Your battery is fully charged when the display shows 100%.

Your machine won’t operate or charge if the ambient temperature is below

5°C (41°F). This is designed to protect both the motor and battery.

Changing your click-in battery

Caring for your floors

Check that the underside of the cleaner head or tool is clean and free from

any objects that may cause damage.

Before vacuuming your flooring, rugs, and carpets, check the manufacturer’s

recommended cleaning instructions.

The brush bar on your machine can damage certain carpet types and floors.

Some carpets will fuzz if a rotating brush bar is used when vacuuming. If this

happens, we recommend vacuuming without the motorised floor tool and

consulting with your flooring manufacturer.

Removing your battery

Push the Battery release button on the handle and slide the battery off

your machine.

Charge the battery.

Refitting your battery

Align your battery with the handle and slide it in. Push firmly until it clicks

into place.

It’s important to fully charge your new machine before using it for the first

time, and after every clean. This is because the battery and monitoring

system’s algorithm ‘learns’ over time, and fully charging your machine helps

it to more accurately calculate and display remaining run time.

The charger connected from

the power supply using the

wall dock.

The charger connected from

the power supply directly

into the front of the battery.

Arrows showing the location of the Battery release button

and the battery coming off the handle when the button is

pressed. The battery is then shown being replaced on the

base of the handle, clicking into place.

Minimise dust contact

Empty as soon as the dirt reaches the MAX level – don’t overfill. Using your

machine when the dirt is above the MAX line may affect the performance

and require more frequent filter washing.

Emptying your bin

Press the red wand release button, on the top of the wand, and pull the wand

away from the bin.

Hold the machine over the bin, pointing downwards.

Firmly push the red bin release button. The bin will slide down, cleaning the

shroud as it goes, and the bin base will open.

The bin base won’t open if the red bin release button isn’t pushed down all

the way.

Release the dirt

Cover your bin tightly in a dust proof bag while you empty. Remove your bin

carefully, seal the bag tightly and dispose.

Close the bin

Push the bin base upwards until your bin and bin base click into place.

Remove your wand

If it is necessary to clean your bin, empty it as shown in the ‘Emptying your

bin’ section.

Press the red button located on the bin runner to release the bin and slide

your bin off the runner.

Only use a damp, lint-free cloth to clean your bin.

Make sure that your bin and seals are completely dry before replacing.

Insert the spine on to the bin runner.

Close your bin by pushing the bin base upwards until the bin and bin base click into place.

Your bin isn’t dishwasher safe and the use of detergents, polishes or air fresheners to clean

your bin isn’t recommended, as it may damage your machine.

Cleaning your bin

Remove your bin

Refit your bin

The MAX mark on the bin of

the machine, showing that

the dirt should not be filled

over the Max mark when

the machine is at the angle

of normal use.

Illustration of the bin being

emptied into a bag with imag-

es demonstrating to take care

not to press the trigger when

emptying the bin.

The bin lid closing with an

audible click and the bin

being pushed upwards with

another click once it is fully

in place.

The bin being removed and the

location of the bin release lever on

the underside of the bin runner.

The bin being pushed back

into position on the bin

runner.

Check the wand for blockages.

Check your cleaner head for blockages, following the instructions to remove

the brush bar, where necessary.

Disconnect your machine from the charger before looking for blockages.

Be careful not to touch the trigger and be aware of sharp objects.

Leave your machine to cool down before looking for blockages.

Don't use your machine when looking for blockages as this could

cause injury.

Clearing blockages

Remove the bin and check for blockages in the main body of your machine.

Make sure any blockages are completely cleared and all parts are fitted

before using your machine.

If your machine detects a blockage, the motor will pulse and you won’t be

able to use your machine until the blockage has been cleared.

If you try to use your machine when the motor is pulsing, it will automatically

cut out.

Refit all parts securely before using your machine.

Clearing blockages isn't covered by your guarantee.

Check the main body

Check the wand and cleaner head

Re–assemble your machine

With the bin removed,

check for blockages, paying

particular attention to the air

inlet, located at on the right–

hand side of the machine just

below the point where the bin

joins the main body of the

machine.

With the wand

removed from the

machine, check for

blockages at both ends

of the wand.

Turn the cleaner head over

to check for obstructions on

the brush bar and air inlet.

Replace your brush bar

Remove your brush bar

Look for obstructions

Don’t put any part of your machine in a dishwasher or use detergents, polishes

or air fresheners.

Press the cleaner head release button on the end of the wand. Place the cleaner

head upside down.

Use a coin to unlock the end cap.

Twist the end cap and remove it from your brush bar. Don’t wash the end cap.

Slide your brush bar out of the cleaner head.

Clearing obstructions from your

Motorbar™cleaner head

Your Motorbar™cleaner head doesn’t have a washable brush bar.

To maintain optimum performance, check your brush bar regularly and clear

any obstructions.

Make sure your machine is disconnected from the charger and make sure your

machine power is turned off.

Clear any debris from your brush bar.

Check inside the cleaner head and remove any debris or blockages.

Your Motorbar™cleaner head and brush bar aren’t washable.

Wipe over with a damp lint-free cloth.

Don’t put any part of your machine in a dishwasher or use detergents,

polishes or air fresheners.

Push the end cap back on to your brush bar and slide it back into the

cleaner head.

Turn the end cap into the locked position.

The lock located on

the side of the cleaner

head, is rotated 90 °to

release the end cap and

the brush bar can be

removed.

The removal of the brush bars

showing the lock in a horizontal

position and the unlock symbol

at 90°anti-clockwise and lock

symbol at 90°clockwise.

Remove the cover and brush bar

Look for obstructions

Re–assemble Hair screw tool

Your Hair screw tool doesn't have a washable brush bar. To maintain optimum

performance, check your brush bar regularly and clear any obstructions.

Make sure your machine is disconnected from the charger and take care not to

touch the trigger.

Remove the Hair screw tool from the wand or machine.

Push the base plate open. Press the red lever down to release the cleaner

head cover.

Pull the cleaner head cover off the main body of the tool.

Pull your brush bar firmly to remove it from the main body.

Check and remove any obstructions from all three parts of your

Hair screw tool.

Your Hair screw tool isn't washable. Wipe over with a damp lint-free cloth.

Don’t put any part of your machine in a dishwasher or use detergents,

polishes or air fresheners.

Put your brush bar back into position and press firmly until it clicks back

into position.

Check the red locking lever is in the unlocked position. Align the cleaner

head cover with the guide on the main body. Push it down until it clicks into

position.

Push the red locking lever up until it clicks into position and push the base

plate back into place.

Clearing blockages from your

Hair screw tool

Location of the lever

to release the brush

bar is located at

the back of the Hair

screw tool.

Slide the housing

back on to the

brush bar and

push the lever on

the back of the

Hair screw tool

upwards to lock.

Andere Handbücher für V11

Inhaltsverzeichnis

Andere Dyson Staubsauger Handbücher

Dyson

Dyson gen5 detect Bedienungsanleitung

Dyson

Dyson DC 35 Bedienungsanleitung

Dyson

Dyson DC14 Telescope Reach Bedienungsanleitung

Dyson

Dyson DC50 Ball Compact Bedienungsanleitung

Dyson

Dyson DCO5 Absolute Bedienungsanleitung

Dyson

Dyson Ball Bedienungsanleitung

Dyson

Dyson DC34 ANIMAL Bedienungsanleitung

Dyson

Dyson DC 51 Bedienungsanleitung

Dyson

Dyson SV12 Bedienungsanleitung

Dyson

Dyson DC02 Bedienungsanleitung

Dyson

Dyson V7 Motorhead Bedienungsanleitung

Dyson

Dyson BALL MULTI FLOOR 2 Bedienungsanleitung

Dyson

Dyson DC47 Bedienungsanleitung

Dyson

Dyson DC26 Bedienungsanleitung

Dyson

Dyson DC27 Bedienungsanleitung

Dyson

Dyson small ball Bedienungsanleitung

Dyson

Dyson V11 Bedienungsanleitung

Dyson

Dyson DC40 Bedienungsanleitung

Dyson

Dyson DC24 Blueprint Limited Edition Bedienungsanleitung

Dyson

Dyson DC41C Bedienungsanleitung

Dyson

Dyson DC05 Bedienungsanleitung

Dyson

Dyson Cinetic Big Ball Bedienungsanleitung

Dyson

Dyson DC29 Bedienungsanleitung

Dyson

Dyson V11 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung