Eaton 5E650iUSB-AU Bedienungsanleitung

powerquality.eaton.com

Eaton 5E

650/850/1100/1500/2000

Important safety instruction - Read before installing product

Personal safety

►The UPS has its own internal power source (the battery). Consequently, the power outlets may be energised even if the UPS is

disconnected from the AC-power source.

►Dangerous voltage levels are present within the UPS. It should be opened exclusively by qualified service personnel.

►The UPS must be properly earthed. Measurements are required to ensure that the total leakage current of the UPS and the

protected equipment does not exceed 3.5mA by checking their characteristics.

►The battery supplied with the UPS contains small amounts of toxic materials. To avoid accidents, the directives listed below must

be observed: Never burn the battery (risk of explosion).

►Do not attempt to open the battery (the electrolyte is dangerous for the eyes and skin).

►Comply with all applicable regulations for the disposal of the battery.

►Batteries constitute a danger (electrical shock, burns). The short-circuit current may be very high. Precautions must be taken for all

handing: remove watches, rings, bracelets and any other metal objects, use tools with insulated handles.

Product safety

►The UPS connection instructions and operation described in the manual must be followed in the indicated order.

►UPS must be connected to a nearby wall outlet that is easily accessible. The UPS can be disconnected from the AC-power source

by removing the power cord.

►Check that the indications on the rating plate correspond to your AC-power system and to the actual electrical consumption of all

the equipment to be connected to the UPS.

►Never install the UPS near liquids or in an excessively damp environment

►Never let a foreign body penetrate inside the UPS.

►Never block the ventilation grates of the UPS.

►Never expose the UPS to direct sunlight or source of heat.

►If the UPS must be stored prior to installation, storage must be in a dry place.

►The admissible storage temperature range is –10°C to +40°C.

Special precautions

►Once installed and connected to the AC power source for the first time, the battery will start to charge. Full charging to obtain the

rated battery backup time requires at least 8 hours.

►Before and after the installation, if the UPS remains de-energised for a long period, the UPS must be energised for a period of 24

hours, at least once every 6 months (for a normal storage temperature less than 25°C). This charges the battery, thus avoiding

possible irreversible damage.

►During the replacement of the battery module, it is imperative to use the same type and number of element previously mounted in

the UPS, in order to maintain an identical level of performance and safety. In case of doubt, don’t hesitate to contact our after sales

department (for more information, refer to the web site http://powerquality.eaton.com/australia).

QUICKSTART

SYSTEM DESCRIPTION

1. Power management port (USB)

2. ON/OFF Button

1. Input cord (220/230/240V AC)

2. 2 Outlets with battery backup

1. Input cord (220/230/240V AC)

2. 3 Outlets with battery backup

3. Fan

5E650/850 5E1100/1500/2000

Charge UPS

for 6 hours

Plug in load equipment

Turn UPS on

TROUBLE SHOOTING

Symptom Possible Cause Remedy

No LED display on the front panel. 1. Battery weak. 1. Charge battery up to 8 hours.

2. Battery defect. 2. Replace with the same type of battery.

3. Power switch is not pressed. 3. Press the power switch again.

Alarm buzzer beeps continuously whenAC supply is

normal. Overload of the UPS. Verify that the load matches the UPS capability specified in

the spec.

When mains power fails, back-up time is shortened. 1. Overload of the UPS. 1. Remove some non-critical load.

2. Battery voltage is too low. 2. Charge battery for 8 hours or more.

3. Battery is defective or aging 3. Replace with the same type of battery.

Mains normal but LED is flashing. Input power cord is loose. Reconnect the power cord properly.

SPECIFICATIONS

MODEL 5E650iUSB-AU 5E850iUSB-AU 5E1100iUSB-AU 5E1500iUSB-AU 5E2000iUSB-AU

CAPACITY VA/W 650VA/

360W 850VA/

480W 1100VA/

660W 1500VA/

900W 2000VA/

1200W

INPUT Input voltage range 170V-280V

OUTPUT

Output on battery 230V

Voltage Regulation

(Bat. Mode) +/-10%

Frequency 50Hz or 60Hz

Frequency Regulation

(Bat. Mode) +/-1 Hz

Output Waveform Modified Sine wave

BATTERY Battery Type (1)12V 7Ah (1)12V 9Ah (2)12V 7Ah (2)12V 9Ah (2)12V 9Ah

Recharge Time 6 hours to 90% after complete discharge

GREEN POWER

FUNCTION Yes (UPS powers off under light load

and no mains power condition) No

COMMUNICATION USB Yes

TRANSFER TIME Typical 2-6ms typical, 10ms max. 4-8ms typical, 10ms max.

INDICATOR AC Mode Green LED lighting

Battery Mode Green LED Flashing

AUDIBLE ALARM

Backup Mode Sounding every 10 seconds

Low Battery Sounding every 1second

Overload Sounding every 0.5 second

Battery replace Sounding every 2 seconds

Fault Continuously sounding

PROTECTION Full Protection Discharge, overcharge, and overload protection

PHYSICAL Dimensions H*W*D 148*100*288 180*133*330

WEIGHT Net Weight 4.6kg 5.1kg 9.3kg 10.5kg 10.5kg

ENVIRONMENT

Operating

Environment 0°C - 40°C

Altitude Maximum operating altitude must not exceed 2000m

Noise Level Less than 45dB

BACK UP TIME For a 100W load 16min 20min 30min 40min 45min

WARRANTY 12 months

Contact: Eaton Power Quality, 10 Kent Road, Mascot NSW, 2020, Australia. http://powerquality.eaton.com/australia

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Eaton UPS Handbücher

Eaton

Eaton 9390 UPS 100160 kVA Bedienungsanleitung

Eaton

Eaton 91PS UPS 8-40 kW Handbuch

Eaton

Eaton 93PM IBC-L Bedienungsanleitung

Eaton

Eaton 5S Bedienungsanleitung

Eaton

Eaton Powerware 9390 Bedienungsanleitung

Eaton

Eaton 20000i Bedienungsanleitung

Eaton

Eaton Ellipse 375 Bedienungsanleitung

Eaton

Eaton 9395XC Bedienungsanleitung

Eaton

Eaton 9PX6K-L Montageanleitung

Eaton

Eaton 91PS Handbuch

Eaton

Eaton Powerware 5115 Bedienungsanleitung

Eaton

Eaton Powerware 9355 Bedienungsanleitung

Eaton

Eaton Power Xpert 9395 Bedienungsanleitung

Eaton

Eaton EX RT 7 Bedienungsanleitung

Eaton

Eaton Powerware 9390 Bedienungsanleitung

Eaton

Eaton 93PM IBC-L Bedienungsanleitung

Eaton

Eaton Powerware 9135 Bedienungsanleitung

Eaton

Eaton EX 2200 RT 2U Bedienungsanleitung

Eaton

Eaton 5E Bedienungsanleitung

Eaton

Eaton multimatic HotSwap MBP3KI Bedienungsanleitung

Eaton

Eaton 93PM IBC-L Bedienungsanleitung

Eaton

Eaton ENV400L/H Bedienungsanleitung

Eaton

Eaton Tripp Lite SmartOnline Series Bedienungsanleitung

Eaton

Eaton 93PM IBC-L Konfigurationshandbuch

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung