Edelbrock 16211-MBN-640 Betriebsanleitung

INSTRUCTION SUPPLEMENT FOR 2000-

LATER HONDA XR650R

SPECIAL NOTE!!!!!!

The Edelbrock carb you have

purchased was designed to be used

with the Honda Power-Up manifold.

Honda part #16211-MBN-640.

Removing stock carburetor and cables.

1. Remove seat and gas tank. Make sure fuel

petcock is in “off” position.

2. Remove throttle cables paying close

attention to routing, as the new cables will

need too be routed the same.

3. Remove stock carburetor and stock throttle

housing.

4. Stuff a dry, clean rag into the intake

manifold to keep debris from entering

engine.

NOTE: It may be easier to remove sub-frame

prior to installation.

Installing the Edelbrock Carburetor and

Throttle Cables

5. Install the throttle cables into the supplied

throttle housing and place onto clean

handlebar end.

6. Remove the rubber carburetor alignment

tabs from the manifold using a razor blade or

sharp cutters. This should be done with the

rag left in the manifold. Be very careful not

to damage the manifold or your hands

while doing this!!

7. Remove the hex pipe plug from the carb cap

using a 11mm or 7/16 wrench. Do not

discard plug, as it will be needed later.

Install the metering adjustment tool included

in the hardware kit. Do not over-tighten as

damage may occur to cap.

8. Install stock fuel line onto fuel banjo with the

elbow pointed up and secure with clamp.

See figure 1.

Figure 1.

9. Remove rag from manifold.

10. Install carburetor into manifold. Do not

tighten yet.

11. Install the pull cable (long shoulder on cable)

into the 4:00 position and the return cable

end into the 1:00 position of the cable

wheel. Secure cables to cable bracket by

replacing end piece and phillips screw. See

figure 2.

Figure 2.

12. Align carburetor as close to vertical as

possible and tighten manifold clamp.

13. Adjust cable until wide-open throttle is

achieved. Adjust return cable to take up the

slack. Note: When throttle cables are

properly adjusted, there should be

approx. 1/8” of free play in the throttle.

14. After throttle cables have been adjusted the

handle bars should be rotated from full right

stop to full left stop while opening and

closing throttle to ensure smooth operation.

Also check to make sure the cables do not

catch or bind on anything, i.e., hand guards,

stabilizers.

15. Secure clamp around air boot onto back of

carburetor.

16. Install Remote Idle Cable into threaded tab

on top of carburetor. Refer to main

instruction manual for remote idle cable

installation and adjustment.

17. Install fuel tank and connect fuel line to

petcock and secure with provided pinch

clamp. Refer to figure 1. Do not bolt tank in

place, as minor adjustments may be

necessary.

18. Turn fuel petcock to “on” and check for

leaks.

19. Open throttle 3-5 times to prime accelerator

pump. Do not open throttle any more than

5 times as this may flood engine!!

20. Once pump is primed, get motor to TDC and

kick through without opening throttle. If

Motor will not fire with a few kicks, open idle

cable ½turn and repeat starting process.

NOTE: If flooding occurs, slowly open

throttle to wide open and hold. With

throttle still open, hold decompression

lever and kick motor through 5-10 times.

Release throttle and decompression lever

and proceed with normal starting

procedure.

For any questions regarding tuning or

installation of Edelbrock products, please

call our toll free tech line M-F 8:00am-12:

30pm, 1:30pm-5:00pm PST.

877-888-7504 ext.2.

Edelbrock #3115 XR650R

Carburetor Specifications

Bore Size: 36mm Tall X 42mm Wide

Needle: 19E @ 18 Clicks

Accelerator Pump Bypass: 1.5 turns out

Alternate Needles: 17E, 21E

Replacement Cables: #9345

Dieses Handbuch passt für folgende Modelle

Andere Edelbrock Automobilteil Handbücher

Edelbrock

Edelbrock 63-0181 Bedienungsanleitung

Edelbrock

Edelbrock 70401 Bedienungsanleitung

Edelbrock

Edelbrock 2980 Bedienungsanleitung

Edelbrock

Edelbrock Chevrolet 5783 Bedienungsanleitung

Edelbrock

Edelbrock 15017 Bedienungsanleitung

Edelbrock

Edelbrock 65272 Bedienungsanleitung

Edelbrock

Edelbrock Later Harley-Davidson 1604 Bedienungsanleitung

Edelbrock

Edelbrock Honda XR400 Betriebsanleitung

Edelbrock

Edelbrock 1551 Bedienungsanleitung

Edelbrock

Edelbrock 5694 (Stainless Steel) Bedienungsanleitung

Edelbrock

Edelbrock 65912 (Ceramic-Coated) Bedienungsanleitung

Edelbrock

Edelbrock 1403-1413 Bedienungsanleitung

Edelbrock

Edelbrock 7798 Bedienungsanleitung

Edelbrock

Edelbrock 2161 Bedienungsanleitung

Edelbrock

Edelbrock 4100 Series Bedienungsanleitung

Edelbrock

Edelbrock PERFORMER-PLUS 2182 Bedienungsanleitung

Edelbrock

Edelbrock 2475 Bedienungsanleitung

Edelbrock

Edelbrock 72176 Bedienungsanleitung

Edelbrock

Edelbrock 60509 Bedienungsanleitung

Edelbrock

Edelbrock 262-400 Bedienungsanleitung

Edelbrock

Edelbrock 72700 Bedienungsanleitung

Edelbrock

Edelbrock 66662 Bedienungsanleitung

Edelbrock

Edelbrock Automobile Parts Bedienungsanleitung

Edelbrock

Edelbrock 5786 Bedienungsanleitung

Beliebte Automobilteil Handbücher anderer Marken

Dakota Digital

Dakota Digital 650277 Bedienungsanleitung

bosal

bosal 037031 Bedienungsanleitung

Vintage Air

Vintage Air 571063 Bedienungsanleitung

GFB

GFB EX38 Bedienungsanleitung

bosal

bosal 028091 Bedienungsanleitung

Dodge

Dodge 8W-43 Kurzanleitung

ICI

ICI Magnum FBM10DGN Bedienungsanleitung

Volant Perfomance

Volant Perfomance 19435 Bedienungsanleitung

BENDIX

BENDIX GEN 4 GEN 5 ABS Bedienungsanleitung

Vintage Air

Vintage Air 571065 Bedienungsanleitung

Rugged Ridge

Rugged Ridge 11503.13 Bedienungsanleitung

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Bedienungsanleitung

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Leitfaden

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Bedienungsanleitung

Toshiba

Toshiba 48-1250 A Bedienungsanleitung

aldes

aldes EHT2 Bedienungsanleitung

Go Rhino

Go Rhino 24371T Bedienungsanleitung

BBK

BBK 18950 Bedienungsanleitung