Edelbrock 5708 Bedienungsanleitung

Catalog #5708

Brochure No. 63-5708

Rev. 10/06 - DA/mc

Page 1 of 2

EDELBROCK CAT-BACK EXHAUST SYSTEM

For 2000-2006 Toyota Tundra 3.7L & 4.7L V8, 2WD & 4WD

Catalog #5708

INSTALLATION INSTRUCTIONS

Please study these instructions carefully before installing your new Edelbrock Cat-Back Exhaust System. If you have any

questions, please contact our Technical Hotline at: 1-800-416-8628 , 7am - 5pm, Monday-Friday, Pacific Standard

Time or e-mail us at [email protected].

Suggested Tools for Installation:

❑3/8" ratchet set and metric sockets ❑9/16” and 15mm wrench ❑Hacksaw

❑Jack and jackstands ❑Liquid penetrant and rubber lubricant

NOTE BEFORE YOU START:

This Edelbrock cat-back system comes with three different I-pipes. This is because some Tundras (between 2000-2006)

use three catalytic converters. Others use 2 catalytic converters and a resonator. If your vehicle came from the factory

with 3 catalytic converters, you will use I-pipe #25-3269 behind the third catalytic converter. If your vehicle came from

the factory with 2 catalytic converters and a resonator, you have the choice of either retaining the resonator for a more

melow exhaust tone, or eliminating the resonator which will give you a more aggressive exhaust tone. See appropriate

steps below.

DISASSEMBLY

Vehicles Equipped with 3 O.E. Catalytic Converters:

1. Remove the V-band clamp behind the rear most

catalytic converter.

2. Remove the stock hanger bars from their isolators

behind the third catalytic converter and remove the

O.E. exhaust system from the vehicle.

3. Install I-pipe #25-3269 behind the rear most

catalytic converter

(See Fig. 1).

Vehicles Equipped with 2 O.E. Catalytic Converters

& A Resonator:

1. If you are retaining your O.E., resonator, cut the

factory I-pipe 10” from the back of the O.E.

resonator. If you want to eliminate the O.E.

resonator, cut the factory I-pipe right where it enters

the O.E. resonator.

IMPORTANT NOTE:

Proper installation is the responsibility of the installer. Improper installation will void warranty and may

result in poor performance and engine or vehicle damage.

INSTALLATION INSTRUCTIONS

IMPORTANT NOTES:

•Support your vehicle with proper jackstands or ramps rated for the total vehicle weight. Place stands so that the rear

axle is allowed to hang free for easy system removal.

•These cat-back systems are engineered to fit stock catalytic converters or equivalent replacements. If you original

system has been modified, Edelbrock will not warranty fit or performance.

Fig. 1

2. Remove the stock hanger bars from their isolators

behind the resonator and remove the O.E. exhaust

system from the vehicle.

Catalog #5708

Brochure No. 63-5708

Rev. 10/06 - DA/mc

Page 2 of 2

Edelbrock Corporation, 2700 California St., Torrance, CA 90503

Tech Line: (800) 416-8628

E-Mail: [email protected]

KIT CONTENTS

WARNING!!!

Exhaust gas contains carbon monoxide, a deadly invisible gas. Correct any leaks before driving!

ASSEMBLY

1. If using original resonator, use 2-1/2” band clamp on

end of I-pipe, #25-3248 and install over cut end of

resonator pipe, slip hanger into rubber isolator. I-

pipe #25-3248 must slide into resonator pipe a

minimum of 2”.

If not using original resonator, use 2-1/2” band

clamp on end of I-pipe #25-3247 and install over cut

end of Y-pipe. I-pipe #25-3247 must slide onto Y-

pipe a minimum of 2”. Cut I-pipe #25-3248 on

reduced end back 3-3/8” so to remove reduced end,

and deburr. Place 3” band clamp on front I-pipe.

Install rear I-pipe #25-3248 into front I-pipe, engage

hanger in rubber isolator.

NOTE: Snug clamps only so system can be adjusted

during installation.

Qty. Part # Desription

❑1 23-4081 Hanger Clamp Assy.

❑1 23-4082 Hanger Clamp Assy.

❑1 25-3247 I-Pipe Front

❑1 25-3248 I-Pipe Rear

❑1 25-3269 I-Pipe (3 catalytic converters)

Qty. Part # Desription

❑1 25-3249 Overaxle Pipe

❑1 25-3223 Tailpipe

❑1 25-55725 Muffler

❑3 46-6612 Band Clamps; 3”

❑2 46-6610 Band Clamps; 2-1/2”

2. Slip the muffler onto the intermediate pipe with a 3”

band clamp on the front. NOTE: Inlet end of muffler

is marked. Snug the clamp so you can adjust the

system later.

3. Install muffler hanger assembly #23-4081 into

muffler rubber isolators from the front of isolators

and slip over muffer outlet.

4. Install overaxle pipe into outlet of muffler.

5. Install overaxle hanger assembly #23-4082 by

slipping over outlet end of overaxle pipe and engage

hanger in rubber isolator.

6. Slip tailpipe onto overaxle pipe, install 3” band clamp

and snug clamp.

7. Align system for clearance to body, frame, and

driveline as you tighten the system from front to rear.

Hanger clamps can be used to properly align system.

8. Check for leaks and correct, if necessary.

Inhaltsverzeichnis

Andere Edelbrock Automobilteil Handbücher

Edelbrock

Edelbrock 70211 Bedienungsanleitung

Edelbrock

Edelbrock 73802 Bedienungsanleitung

Edelbrock

Edelbrock 8123 Bedienungsanleitung

Edelbrock

Edelbrock 8126 Bedienungsanleitung

Edelbrock

Edelbrock Russell R09392S Bedienungsanleitung

Edelbrock

Edelbrock 72279 Bedienungsanleitung

Edelbrock

Edelbrock 4742 Bedienungsanleitung

Edelbrock

Edelbrock VICTOR 8841 Gebrauchsanweisung

Edelbrock

Edelbrock 5682 Bedienungsanleitung

Edelbrock

Edelbrock 396-502 Bedienungsanleitung

Edelbrock

Edelbrock 5734 Bedienungsanleitung

Edelbrock

Edelbrock QwikData 91001 Bedienungsanleitung

Edelbrock

Edelbrock 7129 Bedienungsanleitung

Edelbrock

Edelbrock Nitrous System 63-71940 Bedienungsanleitung

Edelbrock

Edelbrock 5061 Bedienungsanleitung

Edelbrock

Edelbrock 6566 Bedienungsanleitung

Edelbrock

Edelbrock 65052 Bedienungsanleitung

Edelbrock

Edelbrock 5778 Bedienungsanleitung

Edelbrock

Edelbrock 6567 Bedienungsanleitung

Edelbrock

Edelbrock 4771 Bedienungsanleitung

Edelbrock

Edelbrock 68572 Bedienungsanleitung

Edelbrock

Edelbrock 7788 Bedienungsanleitung

Edelbrock

Edelbrock Performer 60039 Bedienungsanleitung

Edelbrock

Edelbrock 5202 Bedienungsanleitung

Beliebte Automobilteil Handbücher anderer Marken

Dakota Digital

Dakota Digital 650277 Bedienungsanleitung

bosal

bosal 037031 Bedienungsanleitung

Vintage Air

Vintage Air 571063 Bedienungsanleitung

GFB

GFB EX38 Bedienungsanleitung

bosal

bosal 028091 Bedienungsanleitung

Dodge

Dodge 8W-43 Kurzanleitung

ICI

ICI Magnum FBM10DGN Bedienungsanleitung

Volant Perfomance

Volant Perfomance 19435 Bedienungsanleitung

BENDIX

BENDIX GEN 4 GEN 5 ABS Bedienungsanleitung

Vintage Air

Vintage Air 571065 Bedienungsanleitung

Rugged Ridge

Rugged Ridge 11503.13 Bedienungsanleitung

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Bedienungsanleitung

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Leitfaden

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Bedienungsanleitung

Toshiba

Toshiba 48-1250 A Bedienungsanleitung

aldes

aldes EHT2 Bedienungsanleitung

Go Rhino

Go Rhino 24371T Bedienungsanleitung

BBK

BBK 18950 Bedienungsanleitung