Edelbrock 6700 Bedienungsanleitung
©2006 Edelbrock Corporation
Catalog #6700
Page 1 of 2 Brochure #63-6700
Rev. 5/06 - DA/mc
Dodge Viper Heat Shields
For 1992-1999 Roadster & 1996-1999 Coupe
Catalog #6700
INSTALLATION INSTRUCTIONS
Please study these instructions carefully before installing your new heat shield. If you have any questions, please contact
our Technical Hotline at : 1-800-416-8628 from 7 am – 5 pm, Monday through Friday, Pacific Standard Time or e-mail
INSTALLATION INSTRUCTIONS
WHEN BEING INSTALLED ON VEHICLES WITH
EDELBROCK T.E.S. #66062:
RIGHT SIDE:
1. Remove top of heater blower box from lower heater
box assembly in engine compartment.
2. Remove the bolts from the coolant reservoir so it can
be moved around.
3. Disconnect spark plug wires from spark plugs and
move out of the way.
4. Loosen the 2nd and 4th upper header flange bolts
for mounting bracket installation.
5. Install one mounting bracket on each of the two
header flange bolts loosened in Step 4. Position the
brackets so that the slot on the end is straight down
under the bolt and bracket is flat on top. These
brackets will angle forward and down slightly when
installed properly.
NOTE: Before attempting to install the heat shield
onto the brackets, first measure the distance
between the threaded holes in the mounting
brackets. You should have 9 1/8” from center to
center of holes. If you don’t, you can bend the
brackets with a pair of pliers or a small hammer.
Doing this will make heat shield installation much
easier.
6. Install the right side heat shield by angling the front
edge of the heat shield down toward the front half of
the header and slipping it forward between the
header and the coolant reservoir and hose. Once it
is down on top of the brackets, slide it toward the
rear of the car, align holes and install supplied bolts
and lock washers.
NOTE: We recommend you use a small amount of
high heat silicone R.T.V. on the top surface of the
mounting bracket to help to keep the shield from
rattling against the mounting brackets.
7. After you have tightened the heat shield to the
mounting brackets, tap on the shield to see if you
have rattles. To eliminate rattles, you can: (1) adjust
the shield at the mounting points “slotted holes”, (2)
bend the heat shield as needed for clearance, (3)
bend mounting brackets slightly for a better fit on
your vehicle.
8. Re-install plug wires onto spark plug.
NOTE: Spark plug boots, wires and hose should not
contact the sharp edges of the heat shield as they
can be damaged.
9. Re-install bolts for coolant reservoir bottle. Use
plastic ties and hose holder provided in kit as
needed to hold coolant hose away from sharp edges
of heat shield.
10. Re-install top half of heater blower box.
LEFT SIDE:
1. Disconnect spark plug wires from spark plugs and
move out of the way.
2. Loosen the 2nd and 4th upper header flange bolts
for mounting bracket installation.
©2006 Edelbrock Corporation
Catalog #6700
Page 2 of 2 Brochure #63-6700
Rev. 5/06 - DA/mc
Edelbrock Corporation, 2700 California St., Torrance, CA 90503
Tech Line: 1-800-416-8628
E-Mail: [email protected]
3. Install one mounting bracket on each of the two
header flange bolts loosened in Step 2. Position the
brackets so that the slot on the end is straight down
under the bolt and the bracket is flat on top. These
brackets will angle back and down slightly when
installed properly. Re-tighten flange bolts with
brackets in place.
NOTE: Before attempting to install the heat shield
onto the brackets, first measure the distance
between the threaded holes in the mounting
brackets. You should have 9 1/8” from center to
center of holes. If you don’t, you can bend the
brackets with a pair of pliers or a small hammer.
Doing this will make heat shield installation much
easier.
4. Install the left side heat shield by positioning the rear
edge down toward the center of the header, then
while moving it down and back, slip it past the valve
cover and foot well sheet metal and into position.
NOTE: We recommend you use a small dab of high
heat silicone R.T.V. on the top surface of the
mounting bracket to help keep the shield from
rattling against the mounting bracket. Align the
shield with the brackets and install bolts and lock
washers supplied in kit.
5. After you have tightened the heat shield to the
mounting brackets, tap on the shield to see if you
have rattles. To eliminate rattles, you can: (1) adjust
the shield at the slotted mounting holes of the shield;
(2) bend the heat shield as needed for clearance; (3)
bend the mounting brackets slightly for a better fit
on your vehicle.
6. Re-install plug wires onto spark plugs.
NOTE: Spark plug boots and wire should not contact
the sharp edges of the heat shield as they may be
damaged.
BOTH SIDES FINAL CHECK: Make sure you have re-
secured all bolts, screw, etc. Make sure all hoses, wires
and plug boots have adequate clearance around sharp
edges of heat shields.
Start vehicle and let idle. If heat shields rattle, refer to
Step 5 (Left Side) or Step 7 (Right Side). When the
vehicle is idling, the heat shields will look like they shake
a lot, but if installed and adjusted properly should not
rattle.
FOR INSTALLING ON VEHICLE WITH OTHER THAN
EDELBROCK T.E.S.
These heat shields are designed to work primarily with
Edelbrock T.E.S. but can be adapted to be used with
other manufacturer’s headers.
It may be necessary to fabricate additional or different
mounting brackets, trim shield if necessary if the
brackets supplied will not work for the brand of headers
you have.
Installations on vehicles with other than Edelbrock T.E.S.
should be done by a skilled fabricator for custom
installation.
Inhaltsverzeichnis
Andere Edelbrock Automobilteil Handbücher
Edelbrock
Edelbrock 8192 Bedienungsanleitung
Edelbrock
Edelbrock Performer RPM 7167 Bedienungsanleitung
Edelbrock
Edelbrock 71001 Bedienungsanleitung
Edelbrock
Edelbrock 541583 Bedienungsanleitung
Edelbrock
Edelbrock Nitrous Refill Station 78000 Bedienungsanleitung
Edelbrock
Edelbrock 5255 Bedienungsanleitung
Edelbrock
Edelbrock 70211 Bedienungsanleitung
Edelbrock
Edelbrock 4789 Bedienungsanleitung
Edelbrock
Edelbrock 60179 Gebrauchsanweisung
Edelbrock
Edelbrock 6501 Bedienungsanleitung
Edelbrock
Edelbrock 6564 Bedienungsanleitung
Edelbrock
Edelbrock Automobile Parts Bedienungsanleitung
Edelbrock
Edelbrock Performer-Plus 2201 Bedienungsanleitung
Edelbrock
Edelbrock 8126 Bedienungsanleitung
Edelbrock
Edelbrock 5747 Bedienungsanleitung
Edelbrock
Edelbrock 72310 Bedienungsanleitung
Edelbrock
Edelbrock 5785 Bedienungsanleitung
Edelbrock
Edelbrock Russell 694540 Bedienungsanleitung
Edelbrock
Edelbrock 1403-1413 Bedienungsanleitung
Edelbrock
Edelbrock Axle-Back Exhaust Systems 5773 Bedienungsanleitung
Beliebte Automobilteil Handbücher anderer Marken
ICI
ICI Magnum FBM10DGN Bedienungsanleitung
Volant Perfomance
Volant Perfomance 19435 Bedienungsanleitung
BENDIX
BENDIX GEN 4 GEN 5 ABS Bedienungsanleitung
Vintage Air
Vintage Air 571065 Bedienungsanleitung
Rugged Ridge
Rugged Ridge 11503.13 Bedienungsanleitung
BENDIX
BENDIX CYCLONE DURADRAIN TRAILER WATER Bedienungsanleitung
