Ekwb EK-Pro GPU WB RTX 6000 - Ni + Inox Bedienungsanleitung

INSTALLATION MANUAL

EK-Pro

GPU WB RTX 6000 – Ni + Inox

GPU WATER BLOCK

- 2 -

This product is compatible with Nvidia Quadro RTX 6000 graphics card.

It is intended for installation by expert users only. Please consult with a

qualiﬁed technician since improper installation may result in damage

to the equipment. EK assumes no liability whatsoever, expressed

or implied, for the use of these products, nor their installation. The

following instructions are subject to change without notice. Please visit

our website at www.ekwb.com for updates. Before the installation of

this product, please read important notice, disclosure, and warranty

conditions printed on the back of the box.

Before you start using this product, please follow these basic guidelines:

Carefully read the manual before beginning with the installation

process.

Remove your graphics card from the computer for the safest

mounting process and to prevent any possible damages to your

GPU or its circuit board (PCB).

EK Fittings require only a small amount of force to screw them

ﬁrmly in place since the liquid seal is ensured with the rubber

O-ring gaskets.

The use of quality market-proven corrosion-inhibiting coolants

is always strongly recommended for any liquid cooling system.

Do not use pure distilled water as a cooling liquid! For best

results, EK recommends the use of EK-CryoFuel Coolants.

- 3 -

TABLE OF CONTENTS

PREPARING THE GRAPHICS CARD 4

REMOVING THE STOCK COOLER 4

CLEANING THE PCB 4

APPLYING THERMAL COMPOUND 5

CUTTING THERMAL PADS 5

PL ACING THERMAL PADS ON PCB 5

INSTALLING THE WATER BLOCK 6

PL ACING THE BLOCK ON THE GRAPHICS CARD 6

ATTACHING THE BLOCK TO THE GRAPHICS CARD 7

CHECKING FOR CONTACT 8

INSTALL ATION OF FITTINGS AND TUBING 8

INSERTING THE GRAPHICS CARD IN THE PC CASE 9

REQUIRED TOOLS 9

SUPPORT AND SERVICE 10

SOCIAL MEDIA 10

- 4 -

PREPARING THE GRAPHICS CARD

STEP 1

REMOVING THE STOCK COOLER

Remove all encircled screws using a Phillips head screwdriver. All heat

sink assembly screws should be removed, including self-adhesive

washers on both sides of the PCB (if present). After that, remove the

I/O bracket.

STEP 1

STEP 2

CLEANING THE PCB

Carefully detach the original stock cooler after removing all screws

that are securing it to the board. Wipe off the remains of the original

thermal compound using a nonabrasive cloth or Q-tip, as shown

in the sample image, until the components and circuit board are

completely clean. EK recommends the use of denatured alcohol for

removing TIM leftovers.

STEP 2

- 5 -

STEP 3

APPLYING THERMAL COMPOUND

Lightly coat the GPU chip with enclosed EK-TIM Ectotherm thermal

grease. For best performance, EK recommends applying thermal

grease in the form of a cross (see sample image).

STEP 3

Thermal Pad F 1.0mm

120

STEP 4

STEP 5

Thermal Pad F 0.5mm

120

F 1.0 mm

STEP 4

CUTTING THERMAL PADS

Your GPU water block comes with thermal pads that have to be cut into

smaller pieces to cover all the VRM components. You must remove the

protective foil from both sides of the thermal pad before installation.

Replacement thermal pads:

1. Thermal Pad F 1.0mm – (120x16mm) – (EAN: 3830046996732)

2. Thermal Pad F 0.5mm – (120x16mm) – (EAN: 3830046996725)

STEP 5

PLACING THERMAL PADS ON PCB

Once cut to size, thermal pads should be placed on the PCB, as illustrated

below. EK made sure to provide you with more than an adequate quantity

of thermal pads to complete this Step.

F 0.5 mm

- 6 -

INSTALLING THE WATER BLOCK

STEP 1

PLACING THE BLOCK ON THE GRAPHICS CARD

Carefully position the water block with preinstalled standoffs on

the graphics card. During this process, please make sure you have

aligned mounting holes on the PCB with holes on the water block

(same applies to other tops).

Pay attention not to use too much force when pressing the

block down to the PCB since chip dies are prone to cracking.

STEP 1 BAG CONTENTS

The content of the bag is universal for all water blocks - you may not

need every screw.

Self-Adhesive

Plastic Washer

M2.5 x 6 AX1

13 pcs

PVC Washer

16 pcs

M2.5 x 4 AX1

16 pcs

M2.5 x 8 AX1

2 pcs

M3 x 4 DIN7985

2 pcs

EK Plug G1/4

2 pcs

2.5 mm Allen Key

1 pc

6 mm Allen Key

1 pc

M2.5 Helix Nut

6 pcs

Thermal Grease

1 pc

- 7 -

STEP 2

ATTACHING THE BLOCK TO THE GRAPHICS CARD

Use a Phillips head screwdriver with the enclosed M2.5X4 and

M2.5X6 screws. EK recommends you start tightening the screws

evenly, around the GPU core ﬁrst, and then continuing outward to

prevent the damage to the GPU. Always use a plastic washer under

each screw!

STEP 2

M2.5 x 4

Plastic Washer

M 2.5 PVC Washer

15 pcs

Phillips Screwdriver

M2.5 x 6 AX1

4 pcs

M2.5 x 4 AX1

11 pcs

M2.5 x 6

M2.5 x 4

- 8 -

Tubing

EK- Plug G1/4

EK-Fitting

STEP 4

INSTALLATION OF FITTINGS AND TUBING

Screw-in two (2) G1/4 threaded male ﬁttings. Attach the liquid

cooling tubes and connect the water block(s) to the cooling loop.

EK recommends using EK-Fittings with this water block.

You can use any opening as an inlet/outlet port.

Do not forget to plug the remaining two openings with enclosed

EK-Plug G1/4 or its equivalent.

CAUTION: In case of using connectors other than EK Compression

Fittings, pay special attention to the length of the ﬁttings’ male G1/4”

thread. 5mm is the maximum G1/4” thread length allowed!

STEP 3

CHECKING FOR CONTACT

If necessary, temporarily remove the water block to check for uniform

surface contact between the block and components. Pay special

attention to the VRM section of the graphics card. Check whether the

water block makes contact with the intended integrated circuit. Then

repeat Steps from the previous section to re-attach the block.

In case you fail to obtain good contact, please check again or

contact our support service at www.ekwb.com/support.

- 9 -

STEP 5

INSERTING THE GRAPHICS CARD IN THE PC CASE

Carefully lift your graphics card with the installed water block and

insert it into your PC’s motherboard PCIexpress expansion slot.

Please bear in mind that your graphics card is very likely heavier than

before it was equipped with the water block.

You need to be very careful when handling the graphics card.

Avoid all unnecessary manipulation of the VGA-water block

assembly that might damage your card or water block.

Phillips Head Screwdriver Scissors

REQUIRED TOOLS

In case you need assistance, please contact:

http://support.ekwb.com/

EKWB d.o.o.

Pod lipami 18

1218 Komenda

Slovenia - EU

EKWaterBlocks

@EKWaterBlocks

ekwaterblocks

EKWBofﬁcial

SUPPORT AND SERVICE

SOCIAL MEDIA

Inhaltsverzeichnis

Andere ekwb Zubehör Handbücher

ekwb

ekwb EK-FC970 GTX Strix Backplate Leitfaden

ekwb

ekwb EK-FC 1070 GTX Ti ASUS Bedienungsanleitung

ekwb

ekwb EK-Momentum ROG Strix Z390I RGB Bedienungsanleitung

ekwb

ekwb EK-FB MSI Z170A XPower Te Monoblock Bedienungsanleitung

ekwb

ekwb EK-FB MSI X470 M7 RGB Bedienungsanleitung

ekwb

ekwb EK-FC7990 SE Leitfaden

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Bedienungsanleitung

ekwb

ekwb EK-Quantum Vector Aorus RTX 2080 D-RGB Bedienungsanleitung

ekwb

ekwb EK-FC Radeon Pro Duo Leitfaden

ekwb

ekwb EK-FC1080 GTX Ti TF6 Bedienungsanleitung

ekwb

ekwb EK-Vector RTX Aorus 2080 Bedienungsanleitung

ekwb

ekwb EK-FC1080 GTX Strix Bedienungsanleitung

ekwb

ekwb EK-FB ASUS Maximus XI HERO Bedienungsanleitung

ekwb

ekwb EK-Velocity WS Series Bedienungsanleitung

ekwb

ekwb EK-FB ASUS Maximus XI EXTREME Bedienungsanleitung

ekwb

ekwb EK-FC970 GTX TFX Backplate Leitfaden

ekwb

ekwb EK-FB ASUS Z 170S Monoblock Bedienungsanleitung

ekwb

ekwb EK-FB GA Z170X Monoblock Bedienungsanleitung

ekwb

ekwb EK-FB ASRock X470 Gaming K4 RGB Bedienungsanleitung

ekwb

ekwb EK-FB ASUS Maximus XI EXTREME Bedienungsanleitung

ekwb

ekwb EK-FC980 GTX WF3 Backplate Leitfaden

ekwb

ekwb EK-FB ASUS X99 Monoblock Bedienungsanleitung

ekwb

ekwb EK-FC980 GTX Classy Backplate Leitfaden

ekwb

ekwb EK-FB ASUS X399 GAMING RGB Monoblock Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

ekwb EK-Pro GPU WB RTX 6000 - Ni + Inox Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken