Ekwb EK-FB ASUS Maximus XI HERO Bedienungsanleitung

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on May 14th 2019

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no

liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual thoroughly before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK-HFB and EK-ACF type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.

4. The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION Sample photo of ASUS Maximus XI

HERO RGB Hero motherboard

BAG CONTENT: Bag content is universal for all water blocks, you may not need all screws.

STEP 1: PREPARING YOUR MOTHERBOARD

STEP 2: PREPARING YOUR MOTHERBOARD

REMOVING STOCK COOLER. Remove all encircled screws. There are 4 screws on

the back of the motherboard that need to be removed in order to remove the factory

installed MOSFET heat pipe cooling solution.

1. APPLYING THERMAL COMPOUND. Apply thermal compound on CPU heat

spreader (IHS) - see sample photo on right with enclosed EK-TIM Ectotherm

thermal grease.

The quantity of about two rice grains is just about right. There is no need to cover

the whole IHS. Applying too much thermal grease will have negative impact on the

cooling performance!

2.. CUTTING THERMAL PADS. Your block comes with thermal pads which needs to be trimmed in order to fit the voltage regulation area (MOSFET) on the

motherboard’s circuit board. WARNING: DIMENSIONS ON PICTURES BELOW ARE SCALED.

Replacement thermal pads @ EKWB web shop:

Thermal PAD F 1mm - (120x16mm) [EAN: 3830046996732]

Do not remove

the PCH (SB)

Cooler!

Installation manual for EK-FB ASUS Maximus XI HERO water block

CPU socket

M9H PCH

(SB)

Mosfets

1. Thermal pad F–1.0mm

(for mosfets):

1. Thermal pad F–1.0mm

(for inductor coils):

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on May 14th 2019

STEP 3: PLACING THE BLOCK ON TO MOTHERBOARD

PLACING THE BLOCK ON THE MOTHERBOARD. Place the EK-FB Maximus XI

HERO Monoblock series water block gently to the motherboard or vice versa (as

shown on photo below). Make sure that mounting holes are aligned.

Plug the 4-pin connector from Water block’s D-RGB LED light to the DRGB_HEADER on

the motherboard. The LED will work if the pin layout on the header is as follows:

+5V digital, empty, Ground.

Please ensure that the arrow indicated on the connector is plugged into the +5V line

as indicated on your motherboard.

STEP 4: ATTACHING BLOCK ON TO THE MOTHERBOARD

Prior to fastening the screws please make sure the mounting holes on the

motherboard’s circuit board are aligned with the water block.

A) Mosfet part: Use four (4) M2,5x5 AX1 screws with PVC washers. Tighten the

screws evenly. Do not use excessive force when tightening the screws!

B) CPU part: Use four (4) M4x8 DIN7984 with screws and washers.

Tighten the screws using enclosed 2.5mm Allen key.

Use the enclosed screws and washers as shown in picture below:

For the EK-FB Maximus XI HERO Monoblock series water block to operate properly the

G1/4 port nearest to the right edge of the water block MUST BE USED AS THE

INLET PORT. EK recommends the use of EK-ACF fittings. When using fittings other

than EK-ACF series please use hose clamps or appropriate substitute to secure the

tubing to the barb. The use of biocide containing and corrosion inhibiting coolant is

always recommended for any liquid cooling system.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver Allen key

Tubing

IMPORTANT: USE

THIS OPENING AS

AN INLET PORT!

M4x8 screws

PVC washer

M2,5x5 AX1 screws

3. PLACING THERMAL PADS ON

MOTHERBOARD. Place thermal pads on PCB as

shown on the picture

PLEASE REMOVE THE PROTECTIVE FOIL

FROM BOTH SIDES OF THE THERMAL PADS

PRIOR TO INSTALLATION!

Place 1mm thermal pads in larger

strips over marked area and make

sure all mosfet chips are covered.

Place 1mm thermal pads in larger

strips over marked area and make

sure all Inductor chips are covered.

Andere ekwb Zubehör Handbücher

ekwb

ekwb EK-Momentum AORUS Z390 MASTER Bedienungsanleitung

ekwb

ekwb EK-Momentum MSI Z390 MEG ACE Bedienungsanleitung

ekwb

ekwb EK-FC 1070 GTX Ti ASUS Bedienungsanleitung

ekwb

ekwb EK-FB ASUS Z 170S Monoblock Bedienungsanleitung

ekwb

ekwb EK-FC7990 SE Leitfaden

ekwb

ekwb EK-FC GV100 PRO Bedienungsanleitung

ekwb

ekwb EK-FC1080 GTX TF6 Bedienungsanleitung

ekwb

ekwb EK-Velocity WS Series Bedienungsanleitung

ekwb

ekwb EK-FC1080 GTX Strix Bedienungsanleitung

ekwb

ekwb EK-FC980 GTX Classy Backplate Leitfaden

ekwb

ekwb EK-FB ASRock X470 Gaming K4 RGB Bedienungsanleitung

ekwb

ekwb EK-FC1070/1080 GTX Bedienungsanleitung

ekwb

ekwb EK-FC970 GTX WF3 Backplate Leitfaden

ekwb

ekwb EK-DCP 4.0 X-RES Leitfaden

ekwb

ekwb EK-FC R9-290X Backplate Handbuch

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Bedienungsanleitung

ekwb

ekwb EK-FC780 GTX Ti Handbuch

ekwb

ekwb EK-FB ASRock X470 Taichi RGB Bedienungsanleitung

ekwb

ekwb EK-XTOP Dual DDC 3.2 PWM Leitfaden

ekwb

ekwb EK-Pro GPU WB RTX 6000 - Ni + Inox Bedienungsanleitung

ekwb

ekwb EK-FC970 GTX Strix Backplate Leitfaden

ekwb

ekwb EK-FB MSI Z170A XPower Te Monoblock Bedienungsanleitung

ekwb

ekwb EK-FB KIT GA-X99 Handbuch

ekwb

ekwb EK-FC Radeon Pro Duo Leitfaden

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

ekwb EK-FB ASUS Maximus XI HERO Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken