Elcometer 223 Bedienungsanleitung

English

Elcometer 223

Digital Surface Profile Gauge

Operating Instructions

223-2_TMA_0152_00_03 (Part Number 4810).fm Page -1 Monday, May 18, 2009 9:47 AM

DISCONTINUED

English

is a registered trademark of Elcometer Limited.

All other trademarks acknowledged.

system or otherwise) or translated into any language, in any form or by any means (electronic, mechanical,

magnetic, optical, manual or otherwise) without the prior written permission of Elcometer Limited

A copy of this Instruction Manual is available for download on our Website via www.elcometer.com.

Doc.No. TMA-0152 Issue 03

Text with Cover No: 4810

223-2_TMA_0152_00_03 (Part Number 4810).fm Page 0 Monday, May 18, 2009 9:47 AM

DISCONTINUED

CONTENTS

Section Page

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2 Getting started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

5 Technical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

6 Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

7 Spares . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

8 Related equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

223-2_TMA_0152_00_03 (Part Number 4810).fm Page 1 Monday, May 18, 2009 9:47 AM

DISCONTINUED

Thank you for your purchase of the Elcometer 223 Digital Surface Profile Gauge. Welcome to Elcometer.

Elcometer are world leaders in the design, manufacture and supply of inspection equipment for coatings

and concrete. Our products cover all aspects of coating inspection, from development through application

to post application inspection.

The Elcometer 223 Digital Surface Profile Gauge is a world beating product. With the purchase of this

product you now have access to the worldwide service and support network of Elcometer. For more

information visit our website at www.elcometer.com

1 INTRODUCTION

The Elcometer 223 Digital Surface Profile Gauge allows accurate measurement of the peak-to-valley height

of the surface profile of blast cleaned surfaces.

To maximise the benefits of your new Elcometer 223 Digital Surface Profile Gauge please take some

time to read these Operating Instructions. Do not hesitate to contact Elcometer or your Elcometer

supplier if you have any questions.

1.1 STANDARDS

Your Elcometer 223 Digital Surface Profile Gauge can be used in accordance with the following National

and International Standards: ASTM D 4417-B, IMO MSC.215(82), SANS 5772, US Navy NSI 009-32, US

Navy PPI 63101-000.

223-2_TMA_0152_00_03 (Part Number 4810).fm Page 2 Monday, May 18, 2009 9:47 AM

DISCONTINUED

1.2 WHAT THE BOX CONTAINS

• Elcometer 223 Digital Surface Profile Gauge

• Glass slide

• 2mm allen key

• 3V Lithium CR2032 Battery (+ battery tool, see “Changing the Battery” on page 6)

• Carry case

• Operating Instructions

Your Elcometer 223 Digital Surface Profile Gauge may be packed in a cardboard and foam package. Please

ensure that this packaging is disposed of in an environmentally sensitive manner. Consult your local

Environmental Authority for further guidance.

223-2_TMA_0152_00_03 (Part Number 4810).fm Page 3 Monday, May 18, 2009 9:47 AM

DISCONTINUED

2 GETTING STARTED

1. Place the foot on the glass slide provided, to ensure the tip is in the

same plane as the base of the foot.

2. Switch the unit on by pressing Control 1 lightly.

3. The unit will display '0.000mm' (or '0.0000"' if set to imperial).

4. Press the foot onto the blasted surface a number of times and allow the

tip to reach the bottom of the profile valleys.

5. The display will read peak to valley height in mm (0.001mm = 1µm).

6. To switch from metric (mm) to imperial (inches), press Control 2 once.

'MM' or 'INCH' is displayed in the bottom left hand corner of the

display. To change units press Control 2 lightly and then release.

7. To switch off, press Control 1 and hold for approximately 3 seconds. If

switched off, the instrument must be reset as above from 1, when next used.

DATA TRANSMISSION

The cable (Sales Part Number T22312213) is connected by removing the RS232 cover and inserting the

cable connector.

3 FEATURES

With the cable connected to the RS232 output, press Control 2, and hold until the Reference mode is

selected. Press Control 1 to transmit the current reading. If the cable is not connected, this operation will

freeze the reading in the display. (Pressing Control 1 again will release hold.)

223-2_TMA_0152_00_03 (Part Number 4810).fm Page 4 Monday, May 18, 2009 9:47 AM

DISCONTINUED

OTHER FEATURES

This electronic measurement device has several features that are not normally used for profile

measurements as follows: -

Resolution

For profile measurement, resolution will normally be set to '0.000mm' or '0.0000". However, resolution of

0.01mm or 0.001" is available by pressing Controls 1 and 2 simultaneously, and holding until the decimal

point moves.

Polarity

For profile measurement, positive polarity is used and the display will show positive numbers relative to

zero. Polarity can be toggled positive to negative or negative to positive, by pressing Controls 1 and 2

simultaneously, and holding until the sign changes.

223-2_TMA_0152_00_03 (Part Number 4810).fm Page 5 Monday, May 18, 2009 9:47 AM

DISCONTINUED

Reference Mode (Ref)

Two independent reference modes can be selected by pressing and holding Control 2 until 'Ref1' and 'Ref2'

appears in the top left hand side of the display.

To switch between 'Ref1' and 'Ref2' press Control 2 once.

Min/Max

This facility freezes minimum or maximum reading. To select the mode, press and hold Control 2 until 'Min'

and 'Max' appears at the top of the display. To clear, press and hold Control 2 until 'MM' or 'INCH' appears

in the bottom left hand corner of the display.

Preset & Measure

To preset size, go into Ref. mode and press and hold Control 2 until 'Preset' appears in the display and then

release Control 2. The display will show a series of zeroes. To set a preset value, each digit is changed in

turn as indicated by the cursor. Press Control 2 lightly to change the cursor position and use Control 1 to

adjust the value.

When the last digit is set, press and hold Control 1.

4 MAINTENANCE

Elcometer products are designed to give many years reliable service under normal operating and storage

conditions.

Changing the Battery

If the display shows 'B' in the bottom left hand corner, the battery should be changed.

Remove the battery cover and the reset plug. Remove the old battery and replace with a Lithium 3V battery.

A special tool for this is included with the battery.

223-2_TMA_0152_00_03 (Part Number 4810).fm Page 6 Monday, May 18, 2009 9:47 AM

DISCONTINUED

5 TECHNICAL SPECIFICATION

Material: Stainless Steel

Dimensions: 105 x 55 x 25mm (4.1 x 2.2 x 1”)

Range: 0 - 1000µm or 0-40mils/thou

Scale: 1µm or 0.1mil/thou

Power Supply: 3V Lithium CR2032 Battery

Weight: 365g (9oz)

6 ACCESSORIES

Your Elcometer 223 Digital Surface Profile Gauge is complete with all the items required to get started.

The following optional accessories are available from Elcometer, or Elcometer supplier. To place an order

please quote the sales par number which follow the description of each accessory.

Miniprinter including Printer Lead X2239964B

Printer Lead T22312213

223-2_TMA_0152_00_03 (Part Number 4810).fm Page 7 Monday, May 18, 2009 9:47 AM

DISCONTINUED

7 RELATED EQUIPMENT

In addition to the Surface Profile Gauge, Elcometer produces a wide range of other Surface Profile

Equipment. Users of the Surface Profile Gauge may also benefit from the following Elcometer product

ranges:

• Elcometer 122 Textex Replica Tape

• Elcometer 125 Surface Comparators

• Elcometer 128 Pictorial Surface Standards

• Elcometer 129 Rubert & Rugotest Surface Comparators

• Elcometer 127 Keane-Tator Surface Comparators & Magnifier

• Elcometer Inspection Kits

For further information contact Elcometer, your local Elcometer supplier or visit www.elcometer.com

223-2_TMA_0152_00_03 (Part Number 4810).fm Page 8 Monday, May 18, 2009 9:47 AM

DISCONTINUED

Inhaltsverzeichnis

Andere Elcometer Messgerät Handbücher

Elcometer

Elcometer 456 Bedienungsanleitung

Elcometer

Elcometer 456 Bedienungsanleitung

Elcometer

Elcometer 456 Ultra Bedienungsanleitung

Elcometer

Elcometer 204 Bedienungsanleitung

Elcometer

Elcometer 320 Bedienungsanleitung

Elcometer

Elcometer 205 Bedienungsanleitung

Elcometer

Elcometer 224 Bedienungsanleitung

Elcometer

Elcometer 456 Bedienungsanleitung

Elcometer

Elcometer 138 Bedienungsanleitung

Elcometer

Elcometer 2080 Bedienungsanleitung

Elcometer

Elcometer SAGOLA Classic S1 Bedienungsanleitung

Elcometer

Elcometer 308 Bedienungsanleitung

Elcometer

Elcometer 138/2 Bedienungsanleitung

Elcometer

Elcometer 456 Bedienungsanleitung

Elcometer

Elcometer UG20DL Bedienungsanleitung

Elcometer

Elcometer 345 Bedienungsanleitung

Elcometer

Elcometer 112 Bedienungsanleitung

Elcometer

Elcometer 6700 Bedienungsanleitung

Elcometer

Elcometer 319/2 Bedienungsanleitung

Elcometer

Elcometer CG30 Bedienungsanleitung

Elcometer

Elcometer CG20 Bedienungsanleitung

Elcometer

Elcometer Novo-Gloss 401 Bedienungsanleitung

Elcometer

Elcometer 456 Bedienungsanleitung

Elcometer

Elcometer 3000 Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung