Elcometer E224C-BI Bedienungsanleitung

Australian Distributor

elcometer Common Gauge Quick Reference Guide

Pages 2-3: Surface Profile Testing

Page 4: Climatic Conditions Testing

Pages 5-6: Dry Film Thickness Testing

Page 7: Porosity Testing

Ph: 1300 503 610

•The Elcometer 224 measures profile on either flat or curved surfaces

•Available with or without memory and Bluetooth®.

•Available with either an integral or separate probe.

•Separate gauge probes offer greater flexibility to suit any application

•Measurement range 0-500μm (0-20mils)

Elcometer 224 Digital Surface Profile Gauge

Model Options ( Gauges )

Part Number Description

Integral Gauge Separate Gauge

E224C-BI E224C-BS Elcometer 224 Model B Digital Surface Profile Gauge

E224C-TI E224C-TS Elcometer 224 Model T Digital Surface Profile Gauge

Range: 0-500μm (0-20mils) Resolution: 1μm (0.1mil) Accuracy: ±5% or ±5μm (±0.2mil)

Part Number Probe Design

T224C500US Flat Surface: Standard

T224C500UARM Flat Surface: Armoured

T224C500UX Convex Surface: Standard

T224C500UXARM Convex Surface:Armoured

Digital Surface Profile Probes / Convex Surface Profile Probes

1. Calibrate on a glass zero plate.

2. Ensure probe is 90° to substrate to ensure accurate readings.

3. Take a minimum of 10 readings over an area to establish the average surface profile.

How to measure surface profile with an elcometer 224

Surface Profile

Testex® Replica Tape

Testex Tape consists of foam with a non-compressible backing.

The foam side is rubbed into the surface providing a permanent mould of the peak-to-valley profile

Testex Tape is available in three profileranges.

There are 50 tests in each roll. Test Area Dimensions: 19 x 54mm (0.75 x 2.23”)

Part Number Metric Range

TESC Coarse 20 - 64μm

TESXC X-Coarse 38 - 115μm

TESXC PLUS X-Coarse Plus 116 - 147μm

TESBT BurnishingTool ( needed to leave impression )

TESGMET Testex Metric Dial Thickness Gauge ( microns)

PHCAL-GMET/7301 Calibration Certificate for Testex Dial Gauge

Thickness Gauge - GMET

The Mitutoyo Thickness Gauge is used to measure the peak-to-valley height

of a surface profilemoulded in the Testex Replica Tape.

• Metric only available

• Quick and easy to use

• Calibration Certificates available at extra cost

Surface Profile Testing cont.

Elcometer 319 Digital Dew Point Meter

Model: Standard Gauge Top Gauge

Part Number G319----S G319----T

Memory - with readingand statistic review

Standard Gauge = Last 10 records Top Gauge= 25,000 records in 999 batches

Accessories

T31920162 Magnetic Surface Temperature Probe; -40 to +200°C (-40 to +392°F)

T9996390- LiquidTemperature Probe; -200 to +1100°C (-328 to +2012°F)

T99921325 USB Cable

T99916063 Wrist Strap

T99923480 Protective Carry Case/Pouch

Dry Film Thickness -

Dry Film Thickness is probably the most critical measurement in the coatings industry. It provides

vital information as to the expected life of the substrate, the product’s fitness for purpose, its

appearanceand ensures compliance with a host of InternationalStandards.

•Integral and Separate gauges available

•Ferrous, Non-Ferrous, Ferrous –Non-Ferrous dual gauges available

•Dust and water resistant rugged design equivalentto IP64

•Fast reading rate of more than 70 readings per minute

• USB and Bluetooth® data output to ElcoMaster™ 2.0 software suite of products

•Calibration Test Certificate comes with Gauges

Elcometer 456 Digital DFT Gauge

Integral Model Options ( Built in Probe )

Scale 1 Range: 0-1500μm (0-60mils) Accuracy*: ±1-3% or ±2.5μm (±0.1mil)

Model E Model B Model S Model T

Elcometer456 Ferrous Integral A456CFEI1 A456CFBI1 A456CFSI1 A456CFTI1

Elcometer456 Non-Ferrous Integral N/A A456CNBI1 See separate gauges with N2 PINIP™ Probe

Elcometer456 Dual FNF Integral A456CFNFEI1 A456CFNFBI1 A456CFNFSI1 A456CFNFTI1

Scale 2 Range: 0-5mm (0-200mils) Accuracy*: ±1-3% or ±20μm (±1.0mil)

For higher resolution & accuracy on thin coatings Scale 2 gauges can be switched to the Scale 1 mode measurement performance

Model E Model B Model S Model T

Elcometer456 Ferrous Integral - A456CFBI2 See separate gauges with F2 PINIP™ Probe

Scale 3 Range: 0-13mm (0-500mils) Accuracy*: ±1-3% or ±50μm (±2.0mils)

Model E Model B Model S Model T

Elcometer456 Ferrous Integral A456CFBI3 See separate gauges with F3 PINIP™ Probe

Elcometer 456 Digital DFT Gauge

Dry Film Thickness –cont.

Separate Model Options ( Requires a Probe to Operate )

Model E Model B Model S Model T

Elcometer 456 Ferrous Separate - A456CFBS A456CFSS A456CFTS

Elcometer 456 Non-Ferrous Separate - A456CNBS A456CNSS A456CNTS

Elcometer 456 Dual FNF Separate - A456CFNFBS A456CFNFSS A456CFNFTS

Accessories

T99922341 Self AdhesiveScreen Protectors (x10)

T99921325 USB Cable

Scale 1 Range: 0-1500μm (0-60mils) Accuracy*: ±1-3% or ±2.5μm (±0.1mil)

Probe Design Ferrous Non-Ferrous Dual Probe

Straight T456CF1S T456CN1S T456CFNF1S

Right Angle T456CF1R T456CN1R T456CFNF1R

PINIP™ T456CF1P T456CN1P T456CFNF1P

Elcometer 456 Common Probe range (Scales 6 –7 ref to catalogue)

Scale 2 Range: 0-5mm (0-200mils) Accuracy*: ±1-3% or ±20μm (±1.0mil)

Probe Design Ferrous Non-Ferrous Dual Probe

Straight T456CF2S T456CN2S -

Right Angle T456CF2R - -

Scale 3 Range: 0-13mm (0-500mils) Accuracy*: ±1-3% or ±50μm (±2.0mils)

Probe Design Ferrous Non-Ferrous Dual Probe

Straight T456CF3S - -

PINIP™ T456CF3P - -

Pinhole & Porosity ( Spark Testing / Holiday Testing )

Premature corrosion of a substrate is usually due to a coating failure.A major cause is the

presence of flaws in the finished coating.

Elcometer 270 Pinhole Detector ( Wet Sponge )

The Elcometer 270 range utilises the wet sponge technique and sets the standard for wet sponge

detectors - high quality, low voltage detectors with a wide range of accessories to meet your

requirements.

Part Number D270----4

Voltage 9V, 67.5V and 90V

Coating Range (Max) 500μm (20mils) 500μm (20mils)

Pinhole Inspector’s Kit The complete pinhole detection kit. T27018191

Elcometer 266 Holiday Detector ( Requires Probe Handle see Below)

The Elcometer 266 revolutionises High Voltage DC testing of coatings porosity

detection making it safer, easier and more reliable than ever before.

Part Number D266----4

Voltage ±5% or ±50V below 1000 Volts

Probe Handles Elcometer 266 Probe Handle (Voltage)*

DC5 (0 - 5kV) DC15 (0 - 15kV) DC30 (0 - 30kV)

T26620033-1 T26620033-2 T26620033-3 ○

Elcometer 280 Pulsed DC Holiday Detector

D280-T-KIT many optionsAvailable to suit pipe work inspectionref. elcometer book

Dieses Handbuch passt für folgende Modelle

Andere Elcometer Messgerät Handbücher

Elcometer

Elcometer Protovale CoverMaster CM52 Bedienungsanleitung

Elcometer

Elcometer SG80BDL Bedienungsanleitung

Elcometer

Elcometer Adhesion Verification Unit Bedienungsanleitung

Elcometer

Elcometer protovale P330 Bedienungsanleitung

Elcometer

Elcometer 103 Bedienungsanleitung

Elcometer

Elcometer 2350 Bedienungsanleitung

Elcometer

Elcometer 204 Bedienungsanleitung

Elcometer

Elcometer 2080 Bedienungsanleitung

Elcometer

Elcometer 319 Standard Bedienungsanleitung

Elcometer

Elcometer 355 Bedienungsanleitung

Elcometer

Elcometer 224 Bedienungsanleitung

Elcometer

Elcometer 224 Bedienungsanleitung

Elcometer

Elcometer 500 Bedienungsanleitung

Elcometer

Elcometer 224 Bedienungsanleitung

Elcometer

Elcometer 224 Bedienungsanleitung

Elcometer

Elcometer 121/2 Bedienungsanleitung

Elcometer

Elcometer 112 Bedienungsanleitung

Elcometer

Elcometer 456 IPC Bedienungsanleitung

Elcometer

Elcometer PTG6 Bedienungsanleitung

Elcometer

Elcometer 331 Series Bedienungsanleitung

Elcometer

Elcometer 2300 Series Bedienungsanleitung

Elcometer

Elcometer 112 Bedienungsanleitung

Elcometer

Elcometer 456 Bedienungsanleitung

Elcometer

Elcometer 701 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung