Electro-Voice RE3 Series Bedienungsanleitung

RE3 UHF Wireless

en Installation manual

en |

Table of contents RE3 UHF

Wireless

2018

-12 | 01 | F.01U.362.808 Installation manual Electro-

Voice

RE3

UHF Wireless Table of contents | en 3

Electro

-Voice Installation manual 2018-12 | 01 |

F.01U.362.808

Table of contents

Table of contents 3

1Safety, precautions, and notices 4

1.1 Important safety instructions 4

1.2 Battery precautions 5

1.3 Notices 5

1.4 Licensing, certifications, restrictions and manufacturers declarations 6

2Short information 9

2.1 Shipping contents 10

3Description 11

4Glossary of terms 13

5Best practices for successful operation 15

6Quick setup 17

6.1 Preparing the receiver 17

6.2 Preparing the transmitter 17

6.3 Sync the transmitter to the receiver 17

6.4 Ensure transmitter input sensitivity is set for best signal level 17

7RE3-RX receiver 19

7.1 Product identification 19

7.2 LCD display 22

7.3 RE3-RX setup menu 22

8RE3-HHT handheld transmitter 36

8.1 Product identification 36

8.2 LCD display 38

8.3 Installing batteries 39

8.4 RE3-HHT setup menu 39

9RE3-BPT bodypack transmitter 41

9.1 Product identification 42

9.2 LCD display 44

9.3 Installing batteries 44

9.4 RE3-BPT Setup Menu 45

10 Accessories for RE3 48

11 Troubleshooting and FAQ 50

11.1 Troubleshooting 50

11.2 Frequently Asked Questions 54

12 Technical data 58

13 Frequency Group / Channel Tables 67

en |

Safety, precautions, and notices RE3 UHF

Wireless

2018

-12 | 01 | F.01U.362.808 Installation manual Electro-

Voice

1Safety, precautions, and notices

1.1 Important safety instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer's

instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug where present. A

polarized plug has two blades with one wider than the other. A grounding type plug has two

blades and a third grounding prong. The wide blade or the third prong is provided for your

safety. If the provided plug does not fit into your outlet, consult an electrician for replacement

of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Unplug the apparatus during lightning storms or when unused for long periods of time.

13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has

been damaged in any way, such as power-supply cord or plug is damaged, liquid has been

WARNING:TO REDUCE THE RISK OF

FIRE OR ELECTRIC SHOCK, DO NOT

OVEREXPOSE THIS APPLIANCE TO RAIN

OR MOISTURE

AVIS: RISQUE DE CHOC ELECTRIQUE, NE

PAS OUVRIR.

WARNING:THE MAINS PLUG OR DC

INLET IS USED AS A DISCONNECT

DEVICE. THE DISCONNECT DEVICE SHALL

REMAIN READILY OPERABLE.

WARNING: CONNECT ONLY TO MAINS

SOCKET WITH PROTECTIVE EARTHING

CONNECTION.

WARNING:TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK) AS THERE ARE NO

USER-SERVICABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED PERSONNEL.

The exclamation point within an

equilateral triangle is intended to alert

the user to the presence of important

operating and maintenance

(servicing) instructions in the

literature accompanying the

appliance.

RE3

UHF Wireless Safety, precautions, and notices | en 5

Electro

-Voice Installation manual 2018-12 | 01 |

F.01U.362.808

spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

14. No naked flame sources, such as lighted candles, should be placed on the apparatus.

15. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

The apparatus should not be exposed to dripping or splashing. Objects filled with liquids, such

as vases or open beverage containers should not be placed on apparatus.

16. To completely disconnect DC power from this apparatus, the DC power supply cord must be

unplugged from the apparatus, or the apparatus’ external power supply must be unplugged

from the AC socket.

17. To completely disconnect AC power from this apparatus’ external power supply, the power

supply plug must be unplugged at the AC socket.

1.2 Battery precautions

Keep batteries out of the reach of children.

Observe and install batteries according to the correct polarity as marked on the battery and the

transmitter battery compartment.

Do not expose the battery to excessive heat such as sunshine, fire, or other sources of high heat.

Always consider the environment issues and follow local regulations when disposing of batteries.

Remove depleted battery immediately.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent

type.

Use only disposable LR6(AA) alkaline or NiMH batteries.

Do not mix new batteries with old ones in the transmitter at the same time.

Do not use different battery types or models.

Do not use a leaking battery. If battery leakage occurs, avoid contact with skin. If contact occurs,

immediately wash thoroughly with soap and water.

If battery leakage comes into contact with your eyes, immediately flush with water and seek

medical attention.

Remove and safely store batteries away from the transmitter when the transmitter will not be used

for 60 or more days.

1.3 Notices

Old electrical and electronic appliances

Electrical or electronic devices that are no longer serviceable must be collected separately and

sent for environmentally compatible recycling (in accordance with the European Waste Electrical

and Electronic Equipment Directive). To dispose of old electrical or electronic devices, you should

use the return and collection systems put in place in the country concerned.

means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written

permission of the publisher. For information on getting permission for reprints and excerpts,

contact Electro-Voice. All content including specifications, data, and illustrations in this manual are

subject to change without prior notice.

en |

Safety, precautions, and notices RE3 UHF

Wireless

2018

-12 | 01 | F.01U.362.808 Installation manual Electro-

Voice

1.4 Licensing, certifications, restrictions and manufacturers

declarations

Regarding handheld transmitters RE3-HHT-5L (480-524 MHz), RE3-HHT-5H (560-596 MHz),

RE3-HHT-6M (653-663 MHz), and bodypack transmitters RE3-BPT-5L (480-524 MHz), RE3-BPT-

5H (560-596 MHz), and RE3-BPT-6M (653-663 MHz):

1.4.1 FCC information

Certified under FCC Part 15 and FCC Part 74.

FCC ID: B5DH2285L, B5DH2285H, B5DH2286M, B5DB1245L, B5DB1245H, B5DB1246M.

NOTE: Regarding RE3-HHT-6M (653-663 MHz) and RE3-BPT-6M (653-663 MHz); use of

frequencies beginning at 653.000 MHz up to 657.000 MHz is covered under FCC Part 74 ID

numbers B5DH2286M and B5DB1246M, and require an LPAS user license, however use of

frequencies between 657.025 up to 663.000 MHz is covered under FCC Part 15, and do not

require an additional user license. For more information, see

https://www.fcc.gov/consumers/guides/operation-wireless-microphones.

CAUTION: Changes or modification made by the user could void the user’s authority to operate

the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

FCC Supplier’s Declaration of Conformity

47 CFR, Section 2.1077 Compliance Information

Product Identifier:

Electro-Voice:

RE3 Wireless Receiver, AASP Active Antenna Splitter, ALPA Active

Log Periodic Antenna, RFAMP Antenna Booster, BC2 Battery Charger

Responsible Party – U.S. Contact Information

Bosch Security Systems, Inc.

130 Perinton Parkway

Fairport, NY 14450

USA

Tel: +1 (585) 223-4060

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not be

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired

operation.

RE3

UHF Wireless Safety, precautions, and notices | en 7

Electro

-Voice Installation manual 2018-12 | 01 |

F.01U.362.808

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment to an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

1.4.2 IC (Industry Canada)

Certified in Canada by IC under RSS-102, and RSS-210, and RSS-Gen

IC: 1321A-RE3HHT488, 1321A-RE3HHT560, 1321A-RE3HHT653, 1321A-RE3BPT488, 1321A-

RE3BPT560, 1321A-RE3BPT653.

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la

classe B est conforme à la norme NMB-003 du Canada.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject

to the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference, including interference that may cause undesired

operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio

exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage

est susceptible d'en compromettre le fonctionnement.

NOTE: Regarding RE3-HHT-6M (653-663 MHz) and RE3-BPT-6M (653-663 MHz); the use of

frequencies between 653.025 up to 663.000 MHz, please check the Canada’s ISED (Innovation,

Science and Economic Development) website for the current information of the license status of

this band.

1.4.3 Licensing information

Licensing: A ministerial license to operate this equipment may be required in certain areas.

Consult your national authority for possible requirements. Changes or modifications not expressly

approved by Electro-Voice could void your authority to operate the equipment. Licensing of

Electro-Voice wireless microphone equipment is the user’s responsibility, and licensability

depends on the user’s classification and application, and upon the selected frequencies on which it

will operate. Electro-Voice advises the user to contact the appropriate telecommunications

authority concerning proper licensing, and before selecting and ordering frequency bands.

1.4.4 EU (European Union)

The CE Declaration of Conformity can be obtained and downloaded from: www.electrovoice.com

This Equipment is in compliance with the following directives:

2011/65/EU RoHS Directive

2012/19/EU WEEE Directive

2014/53/EU RED Directive

Regarding (applies to) handheld transmitter RE3-HHT-5L (480-524 MHz), RE3-HHT-5H (560-596

MHz), RE3-HHT-6M (653-663 MHz), RE3-HHT-8M (823-865 MHz), and bodypack transmitter

RE3-BPT-5L (480-524 MHz), RE3-BPT-5H (560-596 MHz), RE3-BPT-6M (653-663 MHz), and

RE3-BPT-8M (823-865 MHz):

en |

Safety, precautions, and notices RE3 UHF

Wireless

2018

-12 | 01 | F.01U.362.808 Installation manual Electro-

Voice

This equipment is intended for use in wireless microphone applications.

Some countries in the EEA (European Economic Area) have restrictions placed on this equipment.

If an EEA country is not listed it did not have any restrictions of the product at the time this

document was published.

The country codes used in regard to these restrictions are the following:

Austria (AT), Belgium (BE), Cyprus (CY), Denmark (DK), Germany (DE), Greece (EL), Spain (ES),

Ireland (IE), Iceland (IS), Latvia (LV), Lithuania (LT), Malta (MT), Norway (NO), Slovakia (SK),

Sweden (SE) and United Kingdom (UK).

Listed below are these restrictions:

Transmitters in the ranges, 488 – 524 MHz, 560 – 596 MHz and 653 – 663 MHz, require a

license in the following countries: AT, BE, CY, DE, IE, LV, LT, SK, SE, UK.

Transmitters in the ranges, 488 – 524 MHz, 560 – 596 MHz and 653 – 663 MHz, require

the transmitter be used in TV white spaces: AT, DK, IS, MT, NO, ES.

Transmitters in the ranges, 488 – 524 MHz, 560 – 596 MHz and 653 – 663 MHz, if used

outdoor will have geographical restrictions of operation in the United Kingdom (UK)

Transmitters in the range, 823 – 865, require a license for use in the 823 – 832 MHz range

in the following countries: AT, BE, CY, EL, IE, LV, LT, UK.

Transmitters in the range, 488 – 524 MHz, may only use the range 510 – 524 MHz in

Norway (NO).

Note: TV white spaces are gaps between operating TV broadcast stations where there are no

active TV broadcasts.

Always consult your national authority before placing equipment into operation as requirements

and spectrum usage can change.

1.4.5 AU and NZ

This device operates under an ACMA class license and must comply with all the terms of that

license including operating frequencies.

RE3

UHF Wireless Short information | en 9

Electro

-Voice Installation manual 2018-12 | 01 |

F.01U.362.808

2Short information

The following table lists products in a family, with CTN (Commercial Type Number) and identifying

product name DESCRIPTION.

CTN

DESCRIPTION

RE3-ND76-5L

Handheld set with ND76 head 488-524MHz

RE3-ND76-5H

Handheld set with ND76 head 560-596MHz

RE3-ND76-6M

Handheld set with ND76 head 653-663MHz

RE3-ND76-8M

Handheld set with ND76 head 823-865MHz

RE3-ND76-T

Handheld set with ND76 head 803-806MHz

RE3-ND86-5L

Handheld set with ND86 head 488-524MHz

RE3-ND86-5H

Handheld set with ND86 head 560-596MHz

RE3-ND86-6M

Handheld set with ND86 head 653-663MHz

RE3-ND86-8M

Handheld set with ND86 head 823-865MHz

RE3-ND86-T

Handheld set with ND86 head 803-806MHz

RE3-ND96-5L

Handheld set with ND96 head 488-524MHz

RE3-ND96-5H

Handheld set with ND96 head 560-596MHz

RE3-ND96-6M

Handheld set with ND96 head 653-663MHz

RE3-ND96-8M

Handheld set with ND96 head 823-865MHz

RE3-ND96-T

Handheld set with ND96 head 803-806MHz

RE3-RE420-5L

Handheld set with RE420 head 488-524MHz

RE3-RE420-5H

Handheld set with RE420 head 560-596MHz

RE3-RE420-6M

Handheld set with RE420 head 653-663MHz

RE3-RE420-8M

Handheld set with RE420 head 823-865MHz

RE3-RE420-T

Handheld set with RE420 head 803-806MHz

RE3-RE520-5L

Handheld set with RE520 head 488-524MHz

RE3-RE520-5H

Handheld set with RE520 head 560-596MHz

RE3-RE520-6M

Handheld set with RE520 head 653-663MHz

RE3-RE520-8M

Handheld set with RE520 head 823-865MHz

RE3-RE520-T

Handheld set with RE520 head 803-806MHz

RE3-BPOL-5L

Bodypack set, omni lavalier 488-524MHz

RE3-BPOL-5H

Bodypack set, omni lavalier 560-596MHz

RE3-BPOL-6M

Bodypack set, omni lavalier 653-663MHz

RE3-BPOL-8M

Bodypack set, omni lavalier 823-865MHz

RE3-BPOL-T

Bodypack set, omni lavalier 803-806MHz

en |

Short information RE3 UHF

Wireless

2018

-12 | 01 | F.01U.362.808 Installation manual Electro-

Voice

RE3-BPCL-5L

Bodypack set, cardioid mic 488-524MHz

RE3-BPCL-5H

Bodypack set, cardioid mic 560-596MHz

RE3-BPCL-6M

Bodypack set, cardioid mic 653-663MHz

RE3-BPCL-8M

Bodypack set, cardioid mic 823-865MHz

RE3-BPCL-T

Bodypack set, cardioid mic 803-806MHz

RE3-BPHW-5L

Bodypack set, headworn mic 488-524MHz

RE3-BPHW-5H

Bodypack set, headworn mic 560-596MHz

RE3-BPHW-6M

Bodypack set, headworn mic 653-663MHz

RE3-BPHW-8M

Bodypack set, headworn mic 823-865MHz

RE3-BPHW-T

Bodypack set, headworn mic 803-806MHz

RE3-BPGC-5L

Bodypack instrument set 488-524MHz

RE3-BPGC-5H

Bodypack instrument set 560-596MHz

RE3-BPGC-6M

Bodypack instrument set 653-663MHz

RE3-BPGC-8M

Bodypack instrument set 823-865MHz

RE3-BPGC-T

Bodypack instrument set 803-806MHz

RE3-BPNID-5L

Bodypack set, no input device 488-524MHz

RE3-BPNID-5H

Bodypack set, no input device 560-596MHz

RE3-BPNID-6M

Bodypack set, no input device 653-663MHz

RE3-BPNID-8M

Bodypack set, no input device 823-865MHz

RE3-BPNID-T

Bodypack set, no input device 803-806MHz

2.1 Shipping contents

This manual is packaged in a preconfigured set containing a receiver and its supplied accessories,

as well as a transmitter and its supplied accessories. The delivered set configurations vary.

2.1.1 Items contained in all sets

Quantity

Component

Receiver

Receiver antennas

Receiver power supply with four power convention specific AC plug clips

Rack-mount brackets

Rack-mount bracket hole filler plugs

Pack of four (4) screws to mount rack brackets

Safety booklet

Installation manual

Andere Handbücher für RE3 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Electro-Voice Mikrofon Handbücher

Electro-Voice

Electro-Voice Cobalt Co11 Bedienungsanleitung

Electro-Voice

Electro-Voice N/D267a Bedienungsanleitung

Electro-Voice

Electro-Voice PL37 Bedienungsanleitung

Electro-Voice

Electro-Voice HM1 Bedienungsanleitung

Electro-Voice

Electro-Voice RE34 Bedienungsanleitung

Electro-Voice

Electro-Voice PL91 Bedienungsanleitung

Electro-Voice

Electro-Voice RE3-BP0L-T Bedienungsanleitung

Electro-Voice

Electro-Voice RE97TX Bedienungsanleitung

Electro-Voice

Electro-Voice CP212 Bedienungsanleitung

Electro-Voice

Electro-Voice PolarChoice PC-12 Bedienungsanleitung

Electro-Voice

Electro-Voice PC-12/FL Bedienungsanleitung

Electro-Voice

Electro-Voice C090 Bedienungsanleitung

Electro-Voice

Electro-Voice RE20 Bedienungsanleitung

Electro-Voice

Electro-Voice 664 Dimensionsleitfaden

Electro-Voice

Electro-Voice R300 Bedienungsanleitung

Electro-Voice

Electro-Voice N/D478 Bedienungsanleitung

Electro-Voice

Electro-Voice PL70-N/D Bedienungsanleitung

Electro-Voice

Electro-Voice N/D857 Bedienungsanleitung

Electro-Voice

Electro-Voice Cobalt Co7 Bedienungsanleitung

Electro-Voice

Electro-Voice N/D Series II 308A Bedienungsanleitung

Electro-Voice

Electro-Voice PolarChoice PC Boundary Satellite Bedienungsanleitung

Electro-Voice

Electro-Voice RE90H Bedienungsanleitung

Electro-Voice

Electro-Voice N/D367s Bedienungsanleitung

Electro-Voice

Electro-Voice RE38N Bedienungsanleitung

Beliebte Mikrofon Handbücher anderer Marken

IK Multimedia

IK Multimedia iRig Stream MIC PRO Bedienungsanleitung

DAPAudio

DAPAudio RM-101 Bedienungsanleitung

AKG

AKG CHM 21 Bedienungsanleitung

Sennheiser

Sennheiser evolution wireless series EM 100 Bedienungsanleitung

Sony

Sony C-48 Bedienungsanleitung

GIGAMEDIA

GIGAMEDIA GGM PAMICUHFG Bedienungsanleitung

Shure

Shure WH30TQG Bedienungsanleitung

auna PRO

auna PRO MIC-900 Bedienungsanleitung

AKG

AKG D 3800 Bedienungsanleitung

Shure

Shure KSM141 Bedienungsanleitung

MAIIN SOUND

MAIIN SOUND IIN style Bedienungsanleitung

Earthworks

Earthworks TC25 Bedienungsanleitung

Sennheiser

Sennheiser evolution D1 Bedienungsanleitung

Alesis

Alesis MicLink Wireless Bedienungsanleitung

DSPPA

DSPPA D6234 Bedienungsanleitung

Monacor

Monacor IMG STAGELINE ECM-300B Bedienungsanleitung

Ansr Audio

Ansr Audio Scan16 Bedienungsanleitung

Shure

Shure MXA710 Series Bedienungsanleitung