Electro-Voice RE97-2Tx Bedienungsanleitung

RE97-2Tx

Low Profile, Head-worn,

Condenser Microphone

with TA4F Connector

RE97-2Tx

Key Features

o Superior Sound Quality

o Omni-directional Polar Pattern

o Lightweight, Low Profile, and Rugged

o Adjustable Head-Band and Boom

o Swivel Earloops Allow for Left or Right

Side Use

Product Description:

The Electro-Voice®RE97-2Tx is a low profile,

omni-directional, condenser microphone designed

for demanding applications where a hands-free

microphone is required. The RE97-2Tx is intended

for spoken-word use in theatrical performance,

corporate AV presentations, fixed installations,

houses of worship, or any venue where a full-

range, natural, and well-balanced sound is required

from an inconspicuous, lightweight, head-worn

microphone.

The output of the RE97-2Tx is clean and accurate,

while the omni-directional polar pattern ensures

uniform output regardless of the microphone’s

angle relative to the sound source. The RE97-2Tx

head-band is easily adjusted to fit virtually any

head size, is light in weight, and provides a stable

base for the microphone boom.

The microphone boom can be easily adjusted for

optimum placement near the user’s mouth by

sliding the boom forward and backward along the

headband. The microphone boom is made of

special, malleable stainless steel that may be

shaped to better match facial contours. The

earloops are designed for full 360° rotation,

allowing for microphone usage on either side of the

head, as well as convenient flat storage when not

in use.

The supplied windscreen can be utilized in windy

environments and to reduce breath noise. The

RE97-2Tx has a shielded 4ft cable terminated in a

genuine Switchcraft®TA4F connector and is ready

for use with standard EV and Telex body-pack

transmitters including the EV REV-BP, BPU-

2/CSB-1000 and Telex WT-500/WT-1000. The

wire to the body-pack may be conveniently routed

behind the user and attached to a shirt collar with

the included clothing clip.

Technical Specifications:

Transducer: Condenser, back-electret

Frequency Response: 50 – 15 kHz

Polar Pattern: Omni-directional

Sensitivity, 1 kHz: -48 dBV, 4.0 mV/Pascal

Maximum SPL: >125 dB SPL

Equivalent Noise: 32 dBA

Dynamic Range: 93 dB

Output Impedance, 1 kHz: 3000 Ohms

Power Requirements: +5 VDC

Current Consumption: 310 μA

Polarity: Positive Pressure on

Diaphragm Produces a

Positive Voltage on pin 2

Dimensions: See diagram

Cable: 4 ft (1.22 m) long; 0.052 in

(1.30 mm) diameter

TA4F Connector Wiring: Pin 1 – Ground

Pin 2 – Audio

Pin 3 – Bias Voltage

Pin 4 – Unused

Accessories Furnished: Windscreen

Clothing Clip

Gig Bag

Colors Available: Beige, Brown, Black

Net Weight: 0.6 oz (17 g)

Mic and headset only: 0.33

oz (9.4 g)

Optional Accessories: TXA Phantom Power

Adapter

RE97-2Tx Low Profile, Head-worn, Omni-directional, Condenser Microphone

Application Notes:

Figure 1. Unlocking and Rotating the Earloops

Using your RE97-2Tx

Earloops:

The RE97-2Tx arrives with the earloops in the flat storage position. To change the position of the earloops,

first pull the base of the earloop straight away from the headband while gripping the cylindrical connector

(Figure 1).

Next, rotate the earloop 90 degrees, and release. The earloop will “lock” into place when positioned

correctly. To replace the RE97-2Tx in the gig bag, repeat this procedure to flatten the earloops.

Note: You may wear the mic boom on either side of the face. To change sides, simply rotate both earloops

180 degrees.

Headband and Microphone Placement:

Before placing on the user’s head, expand the headband to the largest position by moving the sliders

toward each other until they almost touch (Figure 2).

Figure 2. Headband in the Largest Position

RE97-2Tx Low Profile, Head-worn, Omni-directional, Condenser Microphone

Application Notes (continued):

Headband and Microphone Placement (continued):

Place the earloops on the user’s ears and then pull the sliders

apart, towards the ears, tightening until the headband fits firmly

yet comfortably (Figure 3). Adjustments may be made for

additional comfort or stability by gently bending the earloops

(Figure 4).

Microphone Positioning:

The ideal placement of the microphone is ½ inch behind the corner of the mouth and ½ to 1 inch away

from the face. The signal-to-noise ratio is optimized and breath noise is minimized in this configuration

(Figure 5).

Figure 4. Changing the Earloop Shape

Figure 3. Adjusting the Headband

Figure 5. Suggested Placement

RE97-2Tx Low Profile, Head-worn, Omni-directional, Condenser Microphone

Application Notes (Continued):

Adjusting the Microphone Boom:

The three-pronged snap on the strain relief at the

back end of the microphone boom can be placed

anywhere along the headband. Simply pull the

strain relief off of the headband, move the boom

and microphone to the desired position, and snap

the strain relief back on to the headband (Figure 6).

A slight bend can be put into the boom for ideal

placement of the microphone near the corner of the

mouth. Note: Although the microphone boom is

designed to be malleable, permanent damage to

the microphone may result if bent at an angle

exceeding 45 degrees. To adjust, gently bend the

boom a small amount at multiple locations or

around a curved object rather than bending it

sharply at one point (Figure 7a and Figure 7b).

Figure 6. Adjusting the Microphone Boom

Figure 7a. Do Not Bend Mic Boom Sharply

Figure 7b. Shaping the Mic Boom Gently

Figure 8. Using the Clothing Clip

Using the Clothing Clip:

The microphone cable should be routed behind the

neck of the user and secured in place with the

supplied clothing clip. Allow some slack in the cable

to enable the user’s head complete range of motion

in both directions without pulling the cable from the

clothing clip (Figure 8).

RE97-2Tx Low Profile, Head-worn, Omni-directional, Condenser Microphone

Frequency Response: Polar Response:

Windscreen Assembly:

The windscreen assembly is supplied

with a plastic adaptor to improve

stability.

To apply: Hold the windscreen firmly at

the “A” locations. Firmly press the

microphone into the adaptor until it

stops.

Product Dimensions:

RE97-2Tx Low Profile, Head-worn, Omni-directional, Condenser Microphone

Interfacing RE97-2:

Your RE97-2Tx is configured for use with standard Electro-Voice and Telex bodypack

transmitters. Modifications to your RE97-2 should be performed by a qualified technician only.

Using the microphone in a way other than described in this manual may damage the microphone

and void your warranty.

The following table is provided for your reference should you desire to utilize the RE97-2 with

another manufacturer’s wireless transmitter bodypack. Please verify the specifications of your

transmitter before attempting any changes to your microphone.

Manufacturer Wireless Systems

Connector

Type Suggested Wiring

Pin 1: Shield

Pin 2: Wire

AKG WMS 40 Pro, WMS 400, and WMS 4000

(Transmitters PT 40, PT400, and PT4000) TA3F

Jump Pin 2 to Pin 3

Pin 1: Shield

Jump Pin 1 to Pin 2

Pin 3: Wire

Shunt Pins 3-4 with R = 5k Ohms

Audio-Technica

AT UniPak-type Transmitters ATW-1127,

ATW-1235, ATW-1451, ATW-2110, ATW-

3110a, AEW-T1000, ATW-201, ATW-601,

ESW-T210, and ESW-T211 for the following

systems: 1100, 1200, 1400, 2000, 3000, 4000,

5000 Series Professional; 200 and 600 Series

Freeway; NOT for use with the U100 System

Hirose 4-Pin

HR10A-7P-4S

Pin 1: Shield

Pin 2: Wire

Shunt Pins 2-3 with R = 10k Ohms

Electro-Voice RE-2 (BPU-2); RE-1 (CSB-1000); R100 (BPV) TA4F

Pin 4: Not Connected

Tip: Wire

Sleeve: Shield

(Ring: Not Connected)

Sennheiser Evolution Wireless Systems 100, 300, 500

(Transmitters SK100, SK300, SK500), and G2

Series

3.5 mm (1/8")

Stereo or Mono

Mini-Plug 5V Zener diode: + to tip, - to sleeve

(1N5231 or similar)

Pin 1: Shield

Shunt Pins 2-3 with R = 10k Ohms

Pin 3: Wire

Shure

Performance Gear (UT1); PGX1; SLX1; T

Series (T1, T11); UC1; UHF (U1); UHF-R

(UR1); ULX Professional and ULX Standard

(ULX1)

TA4F

Pin 4: Not Connected

Pin 1: Shield

Pin 2: Wire

Shunt Pins 2-3 with R = 10k Ohms

Telex FMR Series 70, 500, 1000 (Transmitters WT-

55, WT-500, WT-1000); SAFE 1000 (SAFE

WT) TA4F

Pin 4: Not Connected

RE97-2Tx Beige Part Number: PRD000064000

RE97-2Tx Brown Part Number: PRD000077000

RE97-2Tx Black Part Number: PRD000078000

U.S.A. and Canada only. For customer orders, contact Customer Service at:

800/392-3497 Fax: 800/955-6831

Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:

+ 49 9421-706 0 Fax: + 49 9421-706 265

Other International locations. For customer orders, contact Customer Service at:

+ 1 952 884-4051 Fax: + 1 952 736-4212

For warranty repair or service information, contact the Service Repair department at:

800/553-5992 or 402/467-5321

For technical assistance, contact Technical Support at: 800/392-3497 or 952/736-4656

Specifications subject to change without notice.

12000 Portland Avenue South, Burnsville, MN 55337

Phone:952/884-4051, Fax: 952/884-0043

www.electrovoice.com

Part Number LIT000079-000 Rev.A

Inhaltsverzeichnis

Andere Electro-Voice Mikrofon Handbücher

Electro-Voice

Electro-Voice C015P Bedienungsanleitung

Electro-Voice

Electro-Voice PL50-N/D Bedienungsanleitung

Electro-Voice

Electro-Voice RE3 Series Bedienungsanleitung

Electro-Voice

Electro-Voice 635N/D Bedienungsanleitung

Electro-Voice

Electro-Voice US690 Bedienungsanleitung

Electro-Voice

Electro-Voice PL Series Bedienungsanleitung

Electro-Voice

Electro-Voice 607 Bedienungsanleitung

Electro-Voice

Electro-Voice HM7 Bedienungsanleitung

Electro-Voice

Electro-Voice 1776B Bedienungsanleitung

Electro-Voice

Electro-Voice 652 Dimensionsleitfaden

Electro-Voice

Electro-Voice 408 Bedienungsanleitung

Electro-Voice

Electro-Voice N/D957 Bedienungsanleitung

Electro-Voice

Electro-Voice PL44 Bedienungsanleitung

Electro-Voice

Electro-Voice CL-1 Bedienungsanleitung

Electro-Voice

Electro-Voice PL37 Bedienungsanleitung

Electro-Voice

Electro-Voice ND46 Bedienungsanleitung

Electro-Voice

Electro-Voice 625TRSKK Dimensionsleitfaden

Electro-Voice

Electro-Voice US637A Bedienungsanleitung

Electro-Voice

Electro-Voice PL24 Bedienungsanleitung

Electro-Voice

Electro-Voice HM2 Bedienungsanleitung

Electro-Voice

Electro-Voice R300 Bedienungsanleitung

Electro-Voice

Electro-Voice PL88 Bedienungsanleitung

Electro-Voice

Electro-Voice 649A Bedienungsanleitung

Electro-Voice

Electro-Voice Cardinal Bedienungsanleitung

Beliebte Mikrofon Handbücher anderer Marken

IK Multimedia

IK Multimedia iRig Stream MIC PRO Bedienungsanleitung

DAPAudio

DAPAudio RM-101 Bedienungsanleitung

AKG

AKG CHM 21 Bedienungsanleitung

Sennheiser

Sennheiser evolution wireless series EM 100 Bedienungsanleitung

Sony

Sony C-48 Bedienungsanleitung

GIGAMEDIA

GIGAMEDIA GGM PAMICUHFG Bedienungsanleitung

Shure

Shure WH30TQG Bedienungsanleitung

auna PRO

auna PRO MIC-900 Bedienungsanleitung

AKG

AKG D 3800 Bedienungsanleitung

Shure

Shure KSM141 Bedienungsanleitung

MAIIN SOUND

MAIIN SOUND IIN style Bedienungsanleitung

Earthworks

Earthworks TC25 Bedienungsanleitung

Sennheiser

Sennheiser evolution D1 Bedienungsanleitung

Alesis

Alesis MicLink Wireless Bedienungsanleitung

DSPPA

DSPPA D6234 Bedienungsanleitung

Monacor

Monacor IMG STAGELINE ECM-300B Bedienungsanleitung

Ansr Audio

Ansr Audio Scan16 Bedienungsanleitung

Shure

Shure MXA710 Series Bedienungsanleitung