Elkay Soft Sides ERO8C Series Installationshandbuch

97873C (Rev. H - 08/16)

ERO8C*C, *2C

PAGE 1

Installation/Care/Use Manual

Soft Sides™Refrigerated Fountain with FLEXI-GUARD®

To assure you install this model easily and correctly, PLEASE READ THESE

SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK

YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL AND

OTHER APPLICABLE CODES. After installation, leave these instructions inside the

fountain for future reference.

IMPORTANT

ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON

IMPORTANT! INSTALLER PLEASE NOTE.

THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO

WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY

OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO

A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE

IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER

MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE

OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.

SEE FIG. 4

FIG. 2FIG. 1

Installer

B CA

SIMPLY PUSH IN

TUBE TO ATTACH

TUBE IS SECURED

IN POSITION

PUSH IN COLLET

TO RELEASE TUBE

OPERATION OF QUICK CONNECT FITTINGS

PUSHING TUBE IN BEFORE

PULLING IT OUT HELPS TO

RELEASE TUBE

OPERATION OF QUICK CONNECT FITTINGS

SIMPLY PUSH IN

TUBE TO ATTACH

TUBE IS SECURED

IN POSITION

PUSH IN COLLET

TO RELEASE TUBE

PUSHING TUBE IN BEFORE

PULLING IT OUT HELPS TO

RELEASE TUBE

A B C

NOTE: WATER FLOW

DIRECTION

BUILDING WATER

INLET

SERVICE STOP

(NOT FURNISHED)

1/4" O.D. TUBE

WATER INLET

TO COOLER

3/8" O.D. UNPLATED COP-

PER TUBE CONNECT

COLD WATER SUPPLY

WWW.RESTROOMDIRECT.COM 704

•

937

•

2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

PAGE 297873C (Rev. H - 08/16)

ERO8C*C, *2C

FIG. 3

LEGEND

A = 1/4" O.D. TUBE CONNECT (CHILLER WATER OUTLET)

B = 3/8" O.D. TUBE CONNECT (CHILLER WATER INLET) SHUT OFF VALVE BY OTHERS

C = 1-1/4" TRAP FURNISHED

D = ELECTRICAL INLET

ERO8C ROUGH-IN

WWW.RESTROOMDIRECT.COM 704

•

937

•

2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

97873C (Rev. H - 08/16)

ERO8C*C, *2C

PAGE 3

FIG. 5

INSTALLATION INSTRUCTIONS

FIG. 6

10 32, 33

SEE FIG. 8

8, 11

1. Install mounting frame. See mounting frame instructions.

2. Install remote chiller. Remove front panel of chiller. Slide chiller onto the shelf and position it to the left within the guides on the shelf.

3. Attach solenoid valve assy to the underside of cross member of mounting frame. See Figure 7.

4. Make water supply connections. Install a shut-off valve and union connection to building water supply (valve and union not provided). Turn on the

water supply and ush the line thoroughly.

5. Make connection between remote chiller and building supply line. Install the strainer on the chiller inlet tube. Install a 3/8" O.D. unplated copper water

line between the valve and the cooler. Remove all burrs from the outside of the water line. Insert the 3/8" water line into the inlet side of the strainer

by pushing it in until it reaches a positive stop, approximately 3/4" (19mm). See Figures 2 and 5. DO NOT SOLDER TUBES INSERTED INTO THE

STRAINER AS DAMAGE TO THE O-RINGS MAY RESULT. Install the 1/4" x 1/4" union (provided) on the chiller outlet tube.

6. Make connection between remote chiller and solenoid valve assy. Insert end of 1/4" O.D. poly tubing (provided) into union on chiller outlet and the

other end into straight tting on solenoid valve assy.

7. Hang the upper panel on the mounting frame hanger. Align holes in the panel with holes in the mounting frame. Be sure that panel is engaged with

hanger at top of frame before releasing it.

8. Install fountain. Remove bottom cover plate on underside of fountain and save the screws. Mount the fountain to the upper panel and the wall frame

with (4) 5/16" x 3/4" (19mm) long bolts and nuts (provided). Tighten securely.

9. Connect solenoid valve assy and regulator holder in fountain by inserting 1/4" O.D. poly tubing (provided).

10. Remove elbow from end of p-trap and attach it to drain tube. Re-attach elbow to p-trap and cut waste tube to required length using plumbing

hardware and trap as a guide.

11. Connect power cord of sensor to solenoid valve by running it through the back panel and connecting it as shown in Fig. 8. Connectors may be

connected to either terminal on solenoid valve. Attach ground wire to solenoid valve bracket with green ground screw.

12. Turn on water supply. Release air from tank by interrupting infrared beam; steady stream of water assures all air is removed. The sensor has a 30

second maximum ON time. It may be necessary to step away from beam a few times to allow chiller tank to rell. Check for leaks.

13. These products are designed to operate on 20-105 PSI supply line pressure. If inlet pressure is above 105 PSI, a pressure regulator must be

installed in the supply line. Any damage caused by reason of connecting these products to supply line pressures lower than 20 PSI or higher than

105 PSI is not covered by warranty.

14. Make electrical connections to chiller. See chiller instructions.

15. Check stream height from bubbler. Stream height is factory set at 35 PSI . If supply pressure varies greatly from this, remove item 11 (bottom

cover plate) and adjust the screw on the regulator (item 7). Clockwise adjustment will raise stream height and counter-clockwise will lower stream

height. For best adjustment stream height should hit basin approximately 6-1/2" (165mm) from the bubbler.

16. Mount lower panel. Loosen the (2) #10-24 x 5/8" (16mm) screws at frame bottom lip. Slide upper tongue of lower panel under lower edge of already

installed upper panel. Tighten previously loosened screws securely.

17. Replace bottom cover plate to fountain basin using screws provided. Tighten securely.

NOTE: WHEN INSTALLING

REPLACEMENT BUBBLER

AND PEDESTAL, TIGHTEN

ITEM 4 NUT ONLY TO HOLD

PARTS SNUG IN POSITION.

DO NOT OVER TIGHTEN.

FIG. 4

34 34

34 (TO BUBBLER)

CHILLER

INLET

CHILLER

OUTLET

WWW.RESTROOMDIRECT.COM 704

•

937

•

2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

PAGE 497873C (Rev. H - 08/16)

ERO8C*C, *2C

FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816

ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484

PART NO.ITEM NO.

PARTS LIST

DESCRIPTION

TROUBLE SHOOTING AND MAINTENANCE

FIG. 8

826

Orice Assy

Housing Assy

Pedestal

Bubbler Locknut

Drain

Regulator Holder

Regulator

Screw - #10-24 X .50 PHTC

Strainer

Fountain Body

Bottom Cover Plate

Back Panel

Hex Nut

Lower Panel

Union-1/4 X 1/4

Regulator Mounting Bracket

Solenoid Mounting Bracket

Sensor Support Bracket

Solenoid Valve Assy 115V

Solenoid Valve Assy 220/230V

Power Cord 115V

Sensor - Clear

Screw- #8-18 X .37 HHSM

Nut - Regulator

Hex Nut #10-32

Strain Relief

Spacer - 1/2 X .44

Edge Trim

Screw - 1/4-20 X .38 HHTC

Elbow - 1/4 X 1/4

Fitting - 1/4 NPTF X 1/4 O.D.

Screw - #10-24 X .62 HHMS

Screw - 5/16-18 X .75

Hex Nut - 5/16-18

Poly Tubing (Cut To Length)

A54874

56011C

55997C

75580C

LK464

50986C

61313C

112627543890

55996C

28784C

55000665

26837C

40045C

26833C

70683C

22525C

22526C

27240C

31375C

0000000327

31376C

31384C

38417001

56082C

70016C

50203C

51409C

56280C

70256C

70817C

75507C

111008343890

111577243890

111577343890

56092C

1. Orice Assy: Minerals deposits on orice can cause water ow to spurt

or not regulate. Mineral deposits may be removed from the orice with a

small round le not over 1/8" diameter or a small diameter wire.

CAUTION: Do not le or cut orice materials.

2. Stream Regulator: If orice is free of material deposits regulate water

ow according to instructions on page 3.

3. Sensor Control: The sensor has a 2 second delay time. If sensor fails to

operate valve mechanism or operates erratically, check the following:

a) Ensure there are no obstructions within a 40 inch radius from the front

of fountain.

b) Check wire connections at the solenoid valve and at the sensor.

CAUTION: Make sure unit is unplugged before checking any wiring.

c) Ensure proper operation of solenoid valve. If there is an audible clicking

sound yet no water ows, look for an obstruction in the valve itself or

elsewhere in the water supply line.

WARNING: Do not expose sensor to direct sunlight.

4. Sensor Range Adjustment: The electronic sensor used in this fountain

is factory pre-set for a "visual" range of 36 inches. If actual range varies

greatly from this, or a different setting is desired, follow the range

adjustment procedure below:

a) Remove bottom cover of fountain.

b) Remove sensor by removing washers and nuts that secure sensor on

studs.

c) Locate range adjustment screw between the red lenses of the sensor,

then with a small tip screwdriver, rotate the range adjusting screw

clockwise to increase range or counter-clockwise to decrease range.

1/4 turn of screw is equal to approximately 12 - 18 inches of range.

CAUTION: Complete range of sensor (24 - 46 inches) is only one turn of

the adjusting screw.

d) Remount sensor on studs and replace bottom cover.

FIG. 7

REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640

MF100 Mounting Frame

WWW.RESTROOMDIRECT.COM 704

•

937

•

2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Elkay Freiluftbrunnen Handbücher

Elkay

Elkay HTHBHVR8-NF-25N Installationshandbuch

Elkay

Elkay LK4400 Bedienungsanleitung

Elkay

Elkay FLEXI-GUARD EIOA4 1E Series Installationshandbuch

Elkay

Elkay Soft Sides ERO8C C Series Installationshandbuch

Elkay

Elkay ERPA8C Installationshandbuch

Elkay

Elkay 4400BFEVGWR Installationshandbuch

Elkay

Elkay SWIRLFLO EDFPBWM114C Gebrauchsanweisung

Elkay

Elkay VRCTL 8 1D Series Installationshandbuch

Elkay

Elkay Soft Sides ERFPD28C Installationshandbuch

Elkay

Elkay LK4410FR FTN A Series Bedienungsanleitung

Elkay

Elkay EDFAC11PBC Installationshandbuch

Elkay

Elkay 4430 Bedienungsanleitung

Elkay

Elkay Soft Sides EDFP210FP B Series Installationshandbuch

Elkay

Elkay LZO8WSS2KWN Bedienungsanleitung

Elkay

Elkay 4420 Series Bedienungsanleitung

Elkay

Elkay VRCTL8 2C Series Installationshandbuch

Elkay

Elkay SWIRLFLO FLEXI-GUARD ERPB8C 2C Series Installationshandbuch

Elkay

Elkay FLEXI-GUARD ESRC8 3GJO Series Installationshandbuch

Elkay

Elkay EDF214WC Installationshandbuch

Elkay

Elkay 4590 Series Bedienungsanleitung

Elkay

Elkay EDFP220RC Installationshandbuch

Elkay

Elkay EWCDA B Series Installationshandbuch

Elkay

Elkay ERPA8C*A Installationshandbuch

Elkay

Elkay 4410FR-FTN Bedienungsanleitung

Beliebte Freiluftbrunnen Handbücher anderer Marken

Sunnydaze Decor

Sunnydaze Decor XSS-578 Bedienungsanleitung

Campania International

Campania International Bibendum FT-400 Bedienungsanleitung

S.R.Smith

S.R.Smith Color Light Stream 2CLSLBK Bedienungsanleitung

Hozelock Cyprio

Hozelock Cyprio Cascade 1500 Bedienungsanleitung

Campania International

Campania International Juliet Fountain Bedienungsanleitung

YARDART

YARDART FT-155 Bedienungsanleitung

Alpine

Alpine WIN732 Bedienungsanleitung

Campania

Campania Valencia Bedienungsanleitung

Campania International

Campania International FT-320 Bedienungsanleitung

GardenWize

GardenWize SWGSL230 Bedienungsanleitung

Kelkay

Kelkay Easy Fountain Rustic Windmill Bedienungsanleitung

Alpine

Alpine WIN258 Bedienungsanleitung

Bond

Bond Signature Series Bedienungsanleitung

Kenroy Home

Kenroy Home 51112COPBL Installationsanleitung

EasyPro

EasyPro Tranquil Décor HBB39 Bedienungsanleitung

Angelo Decor

Angelo Decor Castillo Bedienungsanleitung

Campania International

Campania International Girona FT-102A Bedienungsanleitung

Campania International

Campania International FT-271 Bedienungsanleitung