Elkay VRCTL8 2C Series Installationshandbuch

Page 1 1000002483 (Rev. B - 11/15)

VRCTL8_2C

Description

Combination Refrigerated Drinking Fountain (Cooler) delivers chilled, clean potable drinking water. Two Level Water Cooler houses the refrigeration

and delivers a steady stream of water for direct drinking with push button activated water supply.

Ratings

• Electrical: 230Vac, 50Hz, (See Nameplate for Amperage), 1 phase.

• Ambient Air Temperature: 50-100.4 °F (10-38 °C).

• Water Pressure: 20-100 psig (0.14-0.69 MPa).

• Maximum Water Temperature: 90 °F (32 °C).

• Refrigerant: HFC-R134a

• Ingress Protection: IP21

• For Indoor Commercial Use only.

• Water Inlet: 3/8”O.D. unplated copper tube.

• Waste Water Outlet: 1-1/2” (38.1mm) O.D. tube

DANGER – Indicates death or serious injury will result if proper precautions are not taken.

WARNING – Indicates death, serious injury or property damage can result if proper precautions are not taken.

CAUTION – Indicates some injury or property damage may result if proper precautions are not taken.

Denitions

Authorized Service Personnel – Factory trained personnel or personnel having working knowledge of electrical, plumbing and

machine (appliance) maintenance procedures.

Safety

DANGER

• Please read these instructions completely before starting the installation or performing any service. Failure to follow the instructions and

safety precautions in this manual can result in serious injury or death.

• After installation, keep these instructions in a safe location for future reference.

• Electric supply must be identical in voltage, cycle, and phase to that specied on nameplate.

• Electrical supply must have Ground Fault Circuit Interrupter (GFCI) protection.

• A means for disconnecting electrical supply to the unit must be incorporated in the xed wiring in accordance with wiring rules. This is

to allow electrical disconnection of the unit from electrical supply after installation.

WARNING

• For use with clean, clear potable drinking water only. Do not use with water that is microbiologically unsafe or of unknown quality

without adequate disinfection before the system.

• Installation and connection to water and electrical mains must be in compliance with local and national laws.

• All Installation and Service work must be performed by an authorized service personnel.

CAUTION

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory, or mental

capabilities or lack of experience and knowledge if they have been given supervision or instructions concerning use of the appliance

in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall

not be made by children without supervision.

• To prevent a metallic taste or increased metal content in the water due to an electrolysis process caused by electrical feedback from

the grounding of electrical equipment to water supply and water waste mains, connect to these mains using non-conductive

materials. The provided in-line strainer meets this requirement.

Installation / Care / Use Manual

Original Instructions

Model: VRCTL8S2JOC

Page 2

VRCTL8_2C

1000002483 (Rev. B - 11/15)

Installation

For correct and safe installation, please read these instructions completely.

• All Installation work must be performed by an authorized service personnel.

• Disconnect electrical supply serving the Installation area to reduce risk of electrocution.

• Unit not suitable for installations where water jets could be used.

DANGER

WARNING

• Shut off water supply serving the Installation area to reduce risk of water damage.

• Ensure proper ventilation by maintaining clearance from cabinet louvers to wall on each side of Cooler as specied in Rough-In.

• Never wire compressor directly to electrical supply.

• Thoroughly ush all water lines and ttings of all foreign matter before connecting to Cooler.

• Warranty is void if Installation is not made in accordance with current Manufacturing instructions.

CAUTION

• Hose-sets are not to be used for connecting to water mains.

• If inlet pressure is above 100 psig (0.69 MPa), a pressure regulator must be installed in water supply line. Any damage caused by

reason of connecting this product to water supply line pressure outside it’s rated pressure, is not covered by warranty.

• Tools/Items required but not provided.

o Water Shut-off Valve with 3/8” (9.5mm) compression outlet.

o Waste Trap (non-metallic)

o Safety Glasses

o Protective Gloves

o Fasteners for wall type

Installation: Cooler Mounting

1. Remove Hanger Bracket fastened to back of cooler by removing one (1) screw.

2. Mount Hanger Bracket as shown in Figure 1.

• NOTE: Hanger Bracket MUST be supported securely. Add xture support carrier if wall will not provide adequate support. Anchor hanger securely

to wall using all ve (5) 5/16” (8mm) diameter mounting holes.

• IMPORTANT: 4-3/4” (121mm) dimension from wall to center line of trap must be maintained for proper t.

3. Hang Cooler on the Hanger Bracket. Be certain the Hanger Bracket is engaged properly in the slots on the cooler back as shown in Figure 1.

4. Loosen two (2) screws holding the lower front panel at the bottom of the cooler base and two (2) screws at the top using the T-25 Torx bit

(Provided). Remove front panel and set aside.

5. Fasten cooler to wall using three (3) 7/16 (11.1mm) Dia. holes. See Figure 1, Item F.

Installation: Water Line connection

1. Ensure Mains Water Supply has Water Shut-off Valve with 3/8” (9.5mm) compression outlet.

2. Connect loose end of supplied 3/8” (9.5mm) unplated copper tube to Water Shut-off Valve. Other end of tube should be connected to inlet of in-

line strainer (Item 47). If not connected, simply insert into inlet tting of strainer until positive stop - approximately 3/4” (19mm).

• NOTE: If 3/8” (9.5mm) copper tube must be cut for proper t, remove all burrs from the outside of tube and re-ush before use.

3. Install waste trap. Remove the slip nut and gasket from the waste trap and install them on the cooler waste line making sure that the end of the

waste line ts into the waste trap. Assemble the slip nut and gasket to the waste trap and tighten securely.

4. It is recommended that the waste trap be insulated to avoid excessive condensation due to chilled water running through the waste trap.

5. Turn on building water supply and open Water Shut-off Valve. Check all connections for leaks and correct any found.

Installation: Electrical connection

1. Rotate fan to insure proper clearance and free fan action.

2. Connect modular (C-13) end of International Power Cord Set (sold

separately) into Power Inlet on Cooler and ensure plug-end reaches

electrical outlet. Do not plug into electrical outlet!

230V Wiring Diagram

POWER INLET

Page 3 1000002483 (Rev. B - 11/15)

VRCTL8_2C

Rough-In: VRCTL8

Figure 1

Service

For proper and safe servicing, please read these instructions completely.

DANGER

• All Service and Maintenance must be performed by an authorized service personnel.

• Disconnect electrical supply to the unit before any service work to reduce risk of electrocution.

• Shut off water supply serving the unit before any service work to reduce risk of water damage.

CAUTION

• Tools/Items required but not provided, for Servicing:

o Safety Glasses

o Protective gloves

o Flathead Screwdriver

Service: Adjustments

1. Temperature Control: Factory set for 50ºF ± 5º (10ºC ± 2.8º) water under normal conditions. To adjust water temperature, turn screw on Item

No. 8 clockwise for colder, counter clockwise for warmer.

2. Water Stream Height: Stream height is factory set at 35 psig (0.24 MPa). If supply pressure varies greatly from this, adjust screw using th

access hole in the pushbutton by inserting a athead screwdriver. Clockwise adjustment will raise stream and Counterclockwise adjustment

will lower stream. For best adjustment, stream should hit basin approximately 6-1/2” (165mm) from bubbler on the downward slope of the basin.

3. Water coming out of Bubbler continuously: When this occurs at the end of the compressor cycle, turn the cold control warmer (counterclockwise)

¼ turn.

Operation: Start-Up

1. Turn on the building water supply and check all connections for leaks.

2. Purge air from all water lines by activating both pushbuttons with your hand.

3. Recheck all water and drain connections with water owing through system.

4. Rotate fan to ensure proper clearance and free fan action.

5. Connect plug-end of International Power Cord Set (sold separately) into electrical outlet.

6. After verifying that the water cooler is properly connected and operational, replace and reattach the cooler front panel by tightening (4) screws.

2 7/16"

63mm

10"

254mm

127mm

1 1/2"

38mm

37 1/2"

952mm

6 1/2"

166mm

ORIFICE

HEIGHT

ALTURA DEL

ORIFICIO

HAUTEUR DE

L'ORIFICE

ORIFICE

HEIGHT

ALTURA DEL

ORIFICIO

HAUTEUR DE

L'ORIFICE

1 3/8"

35mm 1 3/8"

35mm

5 3/4"

146mm 5 3/4"

146mm

1 3/8"

35mm 1 3/8"

35mm

5 3/4"

146mm 5 3/4"

146mm

18 1/16"

459mm

FINISHED FLOOR

PISO ACABADO

PLANCHER FINI

5/16" (8mm) DIA. (10 HOLES)

8mm (10 AGUJEROUS)

8mm (10 TROUS)

20 1/8"

511mm

4 1/2"

114mm

6 1/4"

159mm

18 3/4"

476mm

25 1/8"

638mm

3 1/2"

89mm

RIM HEIGHT

ALTURA DEL

ORIFICIO

HAUTEUR DE

L 'ORIFICE

18 5/8"

474mm

12 5/16"

312mm

4 3/4"

121mm

27"

686mm

31 7/8"

810mm

32 15/16"

837mm

39 1/2"

1003mm

2 5/8"

67mm

203mm

13 7/8"

351mm

20 3/8"

518mm

HANGER BRACKET

FIJADOR DE SUSPENSION

SUPPORT DE SUSPENSION

*6 3/4"

173mm

* REDUCE HEIGHT BY 3” FOR INSTALLATION OF CHILDRENS ADA COOLER * ADA REQUIREMENT

LEGEND:

A = Water Mains Supply, 3/8” (9.5mm) O.D. compression outlet of Shut-off Valve (not provided) to be 1-1/2” (38mm) from Wall.

B = Waste Outlet, 1-1/4” (31.8mm) O.D. Drain Tube

C = 1-1/4” (31.8mm) Trap (not provided).

D = Electrical Mains Supply Duplex Outled, 3-wire in Recessed Box. Must have Ground Fault Circuit Interrupter (GFCI) protection.

E = Ensure proper ventilation by maintaining 6” (152mm) minimum clearance from cabinet louvers to wall.

F = 7/16” (11mm) Bolt holes for fastening unit to wall.

Page 4

VRCTL8_2C

1000002483 (Rev. B - 11/15)

7. Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free

connectors which utilize o-ring water seal. To remove tubing from the tting,

relieve water pressure, push in on the gray collar before pulling on the tubing.

To insert tubing, push tube straight into tting until it reaches a positive stop,

approximately 3/4” (19mm). See Figure 2.

Service: Inspection/Replacement

• Inspect Cooler twice each year for proper operation and performance.

• Inspection of the unit will require disconnecting electrical supply, removal of panels, etc. and reassembly and return to service practices.

1. Lower Front Panel and Front Dispenser Panel: To access the refrigeration system and plumbing connections, loosen two (2) screws holding the

lower front panel at the bottom of cooler base and two (2) screws at the top using the provided T-25 Torx bit. To gain access to the regulator,

bubbler, and push button assembly remove (2) screws on the underside of the front dispenser panel (Item 34) using the provided T-20 Torx Bit.

Tilt the bottom of the panel toward you, and slide the panel down to remove it.

2. Bubbler: To remove the bubbler, rst disconnect the electrical and water supply. The underside of the bubbler can be reached through the front

dispenser panel (Item 34). Follow the above instructions to remove the Front Dispenser Panel. To remove the bubbler, loosen bubbler nipple from

the underside of the bubbler (Item 4) and remove the tubing from the quick connect tting. See Figure 2. When installing replacement bubbler,

tighten nipple only to hold parts snug in position. Do Not Overtighten. After servicing, replace the Front Dispenser panel and two (2) screws.

3. Cleaning Strainer: To clean the strainer (Item 47), rst shut off water supply and remove strainer from waterline. Remove plug and screen. Clean

screen and rinse thoroughly with water. Insert screen back into strainer and reassemble. Lubricate O-Ring with food grade pharmaceutical mineral

oil. Do not overtighten plug or ttings. See gure 3.

B CA

SIMPLY PUSH IN

TUBE TO ATTACH

TUBE IS SECURED

IN POSITION

PUSH IN COLLET

TO RELEASE TUBE

OPERATION OF QUICK CONNECT FITTINGS

PUSHING TUBE IN BEFORE

PULLING IT OUT HELPS TO

RELEASE TUBE

OPERATION OF QUICK CONNECT FITTINGS

SIMPLY PUSH IN

TUBE TO ATTACH

TUBE IS SECURED

IN POSITION

PUSH IN COLLET

TO RELEASE TUBE

PUSHING TUBE IN BEFORE

PULLING IT OUT HELPS TO

RELEASE TUBE

A B C

Service: Inspection/Cleaning

• Inspect Cooler twice each year for proper operation and performance.

• Inspection of the unit will require disconnecting electrical supply, removal of panels, etc. and reassembly and return to service practices.

1. Cleaning: Warm, soapy water or mild household cleaning products can be used to clean the exterior panels. Extra caution should be used to

clean the mirror nished stainless steel panels. They can be easily scratched and should only be cleaned with mild soap and water or Windex

glass cleaner and a clean, soft cloth. Use of harsh chemicals or petroleum based or abrasive cleaners will void the warranty.

2. Bubbler: Mineral deposits on the orice can cause water ow to spurt or not regulate. Mineral deposits may be removed from the orice with a

small round le not over 1/8” (3 mm) diameter or small diameter wire.

• CAUTION : DO NOT le or cut orice material. Care must be taken not to damage the orice(s)

3. Condenser Fan Motor: Conrm condenser fan turns freely. If the condenser fan does not spin freely, have an authorized service personnel replace.

4. Ventilation: Cabinet louvers and condenser ns should be periodically cleaned with a brush, air hose or vacuum cleaner. Cleaning should be

done twice each year or more frequently if needed due to environment. Excess dirt or poor ventilation can cause no cold water and compressor

cycling on the compressor overload protector.

5. Water Flow: Conrm proper water ow. If water ow is slow, inspect lter or inline strainer for restriction. Replace lter cartridge if required.

Disassemble inline strainer and clean if required.

6. Lubrication: Motors are lifetime lubricated.

ACBD

A = Plug with 7/8" (22.2mm) Hex

B = O-ring

C = Screen

D = Strainer Body with 1" (25.4mm) Hex Figure 3

Figure 2

VANDAL RESISTANT BUBBLER DETAIL

Basin

Estanque

Bassin

220V Power Inlet Detail

Figure 4

Figure 5

Page 5 1000002483 (Rev. B - 11/15)

VRCTL8_2C

Figure 6

49 (8)

40 (TL)

41 (TLR)

59 31

14, 17, 18

(Items 31 & 24 also

used on the LH unit)

13 9

62 61

Page 6

VRCTL8_2C

1000002483 (Rev. B - 11/15)

42, 43

1, 4

6, 7, 22, 45

See Fig. 4

See Fig. 6

49 12

40 (TL)

41 (TLR)

49 35 8

38 (TL)

39 (TLR)

59, 61, 62

16 9, 13,

23,30

2, 3, 5

1, 4

9, 13, 23, 30

Figure 7

Page 7 1000002483 (Rev. B - 11/15)

VRCTL8_2C

Replacement Parts: 230V Parts List *Includes Relay & Overload. If under Warranty, replace with same Compressor used

in original assembly.

NOTE: All correspondence pertaining to any of the above water cooler or orders for

repair parts MUST include Model number and Serial number of cooler, name and part

number of replacement part.

NOTE: “NS” indicates item is not shown on manual.

ITEM

NO. PART NO. DESCRIPTION

11*

56305C

100806740570

101474551730

15009C

19037000

30664C

31431C

35839C

110868642550

35870C

1000002147

98751C

160270508640

50986C

45866C

56092C

15005C

61313C

66703C

66810C

70002C

70009C

600985451640

28617C

28963C

22897C

45662C

45737C

75672C

100147140560

28596C

See Color Table

66743C

56237C

40045C

70018C

75524C

55996C

45736C

75570C

75661C

70864C

56033C

66576C

45929C

27124C

55931C

45876C

75583C

56121C

70682C

75588C

75589C

35826C

35827C

75520C

75523C

28551C

Gasket - Bubbler

Grommet - Compressor Mtg.

Stud - Compressor Mtg.

Nipple - Bubbler

Clip - Compressor Mtg.

Fan Blade

Fan Motor

Cold Control

Screw - #10-24 x .75 Socket Hd.

Power Cord

Compressor Serv. Pak (50Hz)

Kit - Relay/OverLoad/Cover (50Hz)

Strainer - Bright

Holder - Regulator

Bubbler Assy.

Tubing - Poly (Cut To length)

Retaining Nut

Regulator

Drier

Evaporator Assembly

Screw - #10 x 1/2” Lg. HHSM

Screw - Fan Motor

Drain Plug 1-1/2

Screen - VR

Basin - Stainless Steel

Panel - Bottom Dispenser

Button - Push

Sleeve - Push Button

Cap Screw

Gasket - Drain

Panel - Screen

Panel - RH Dispenser Side

Panel - LH Dispenser Side

Panel - Dispenser Front

Panel - Front Lower

Panel - RH Rear

Panel - LH Rear

Panel - RH Rear TL

Panel - RH Rear TLR

Panel - LH Rear TL

Panel - LH Rear TLR

Condenser

Shroud Fan

Hex Nut

Hex Nut - Fan Blade

Clip (Front & Rear Panels)

Strainer

Half Nut - Regulator

Screw - #10 x .50 Pinned Torx

Screw - #8 x .50 Pinned Torx

Screw - #8 x .62 Torx/Slot

Washer

Heat Exchanger

Tube - Drain

Cover - Cold Control

Cover - Dispenser Bottom

Drain Tube Assy.

Elbow

Elbow - Drain

Tee 1/4

Nut - 1-1/4” Slip Joint

Gasket

Power Inlet

Wire Assembly

Torx Tool - T25

Torx Tool - T20

Hanger Bracket

Stainless Steel

PANEL COLOR

COLOR TABLE

Item No. 40

Part No.

Item No. 32

Part No.

Item No. 33

Part No.

Item No. 34

Part No.

Item No. 35

Part No.

Item No. 36

Part No.

28525C28519C 28516C 28536C28522C 22955C

Refrig. Unit Item No. 41

Part No.

28562C

Stainless Steel

PANEL COLOR

COLOR TABLE

Item No. 38

Part No.

Item No. 32

Part No.

Item No. 33

Part No.

Item No. 34

Part No.

Item No. 35

Part No.

Item No. 37

Part No.

28539C28519C 28516C 28528C28522C 22955C

Left Unit

Item No. 39

Part No.

28559C

For Replacement Parts, contact your local distributor or call 1.800.834.4816

Elkay Manufacturing Co. 2222 Camden Court – Oak Brook, IL 60523 U.S.A – 630.574.8484

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Elkay Freiluftbrunnen Handbücher

Elkay

Elkay 4400FR-FTN Series Bedienungsanleitung

Elkay

Elkay EZS8WS 1F Series Gebrauchsanweisung

Elkay

Elkay 4400FR Series Bedienungsanleitung

Elkay

Elkay EFRC8CDC-A Installationshandbuch

Elkay

Elkay Swirlflo EDFPB114FPC Installationshandbuch

Elkay

Elkay HEWD K Series Installationshandbuch

Elkay

Elkay 4400FR Series Bedienungsanleitung

Elkay

Elkay 4592 FTN Series Bedienungsanleitung

Elkay

Elkay ERPA8C Installationshandbuch

Elkay

Elkay EHFRA7FC*A Installationshandbuch

Elkay

Elkay EHWM214C*A Installationshandbuch

Elkay

Elkay Swirlflo EDFPB117FP Installationshandbuch

Elkay

Elkay FLEXI-GUARD ESRC8,13 1D Series Installationshandbuch

Elkay

Elkay Soft Sides ERO8C C Series Installationshandbuch

Elkay

Elkay 4420FR FTN A Series Bedienungsanleitung

Elkay

Elkay Swirlflo EDFPBW114FP Bedienungsanleitung

Elkay

Elkay SWIRLFLO ENOBM28K Gebrauchsanweisung

Elkay

Elkay 4420BF1UDB Series Bedienungsanleitung

Elkay

Elkay 4400BF Bedienungsanleitung

Elkay

Elkay EFA8 2YJO Series Installationshandbuch

Elkay

Elkay Halsey Tailor 4400DB Bedienungsanleitung

Elkay

Elkay SWIRLFLO FLEXI-GUARD ENOBM8C Installationshandbuch

Elkay

Elkay SWIRLFLO ENOBM28RAK Installationshandbuch

Elkay

Elkay Soft Sides ERFP8C C Series Installationshandbuch

Beliebte Freiluftbrunnen Handbücher anderer Marken

Sunnydaze Decor

Sunnydaze Decor XSS-578 Bedienungsanleitung

Campania International

Campania International Bibendum FT-400 Bedienungsanleitung

S.R.Smith

S.R.Smith Color Light Stream 2CLSLBK Bedienungsanleitung

Hozelock Cyprio

Hozelock Cyprio Cascade 1500 Bedienungsanleitung

Campania International

Campania International Juliet Fountain Bedienungsanleitung

YARDART

YARDART FT-155 Bedienungsanleitung

Alpine

Alpine WIN732 Bedienungsanleitung

Campania

Campania Valencia Bedienungsanleitung

Campania International

Campania International FT-320 Bedienungsanleitung

GardenWize

GardenWize SWGSL230 Bedienungsanleitung

Kelkay

Kelkay Easy Fountain Rustic Windmill Bedienungsanleitung

Alpine

Alpine WIN258 Bedienungsanleitung

Bond

Bond Signature Series Bedienungsanleitung

Kenroy Home

Kenroy Home 51112COPBL Installationsanleitung

EasyPro

EasyPro Tranquil Décor HBB39 Bedienungsanleitung

Angelo Decor

Angelo Decor Castillo Bedienungsanleitung

Campania International

Campania International Girona FT-102A Bedienungsanleitung

Campania International

Campania International FT-271 Bedienungsanleitung