Emerson Micro Motion T Series Bedienungsanleitung

Installation Manual

20002172, Rev BC

February 2020

Micro Motion™ T-Series Coriolis Flow and

Density Sensors

Safety messages

Safety messages are provided throughout this manual to protect personnel and equipment. Read each safety message carefully

before proceeding to the next step.

Safety and approval information

This Micro Motion product complies with all applicable European directives when properly installed in accordance with the

instructions in this manual. Refer to the EU declaration of conformity for directives that apply to this product. The EU declaration

of conformity, with all applicable European directives, and the complete ATEX Installation Drawings and Instructions are available

on the internet at www.emerson.com or through your local Micro Motion support center.

Information affixed to equipment that complies with the Pressure Equipment Directive, can be found on the internet at

www.emerson.com.

For hazardous installations in Europe, refer to standard EN 60079-14 if national standards do not apply.

Other information

Full product specifications can be found in the product data sheet. Troubleshooting information can be found in the configuration

manual. Product data sheets and manuals are available from the Micro Motion web site at www.emerson.com.

Return policy

Follow Micro Motion procedures when returning equipment. These procedures ensure legal compliance with government

transportation agencies and help provide a safe working environment for Micro Motion employees. Micro Motion will not accept

your returned equipment if you fail to follow Micro Motion procedures.

Return procedures and forms are available on our web support site at www.emerson.com, or by phoning the Micro Motion

Customer Service department.

Emerson Flow customer service

Email:

•Worldwide: [email protected]

•Asia-Pacific: [email protected]

Telephone:

North and South America Europe and Middle East Asia Pacific

United States 800-522-6277 U.K. 0870 240 1978 Australia 800 158 727

Canada +1 303-527-5200 The Netherlands +31 (0) 704 136

666

New Zealand 099 128 804

Mexico +41 (0) 41 7686

111

France 0800 917 901 India 800 440 1468

Argentina +54 11 4837 7000 Germany 0800 182 5347 Pakistan 888 550 2682

Brazil +55 15 3413 8000 Italy 8008 77334 China +86 21 2892 9000

Central & Eastern +41 (0) 41 7686

111

Japan +81 3 5769 6803

Russia/CIS +7 495 995 9559 South Korea +82 2 3438 4600

Egypt 0800 000 0015 Singapore +65 6 777 8211

Oman 800 70101 Thailand 001 800 441 6426

Qatar 431 0044 Malaysia 800 814 008

Kuwait 663 299 01

South Africa 800 991 390

Saudi Arabia 800 844 9564

UAE 800 0444 0684

Contents

Chapter 1 Before you begin............................................................................................................5

1.1 About this document........................................................................................................................5

1.2 Hazard messages..............................................................................................................................5

1.3 Related documentation....................................................................................................................5

Chapter 2 Planning........................................................................................................................ 7

2.1 Installation checklist.........................................................................................................................7

2.2 Best practices................................................................................................................................... 8

2.3 Temperature limits...........................................................................................................................8

2.4 Recommendations for hygienic and self-draining applications......................................................... 9

Chapter 3 Mounting.....................................................................................................................13

3.1 Mount the sensor........................................................................................................................... 13

3.2 Attach extended electronics...........................................................................................................13

3.3 Rotate junction box or 800 core processor (optional)..................................................................... 15

Chapter 4 Transmitter power and I/O wiring................................................................................ 17

4.1 Options for wiring...........................................................................................................................17

4.2 Connect 4-wire cable......................................................................................................................18

4.3 Connect the 9-wire cable ............................................................................................................... 22

Chapter 5 Grounding....................................................................................................................23

Chapter 6 Supplementary information.........................................................................................25

6.1 Purge the sensor case .................................................................................................................... 25

Installation Manual Contents

20002172 February 2020

Installation Manual iii

Contents Installation Manual

February 2020 20002172

iv Micro Motion T-Series

1 Before you begin

1.1 About this document

This document provides information on planning, mounting, wiring, and grounding the T-

Series sensor.

The information in this document assumes that users understand basic transmitter and

sensor installation, configuration, and maintenance concepts and procedures.

1.2 Hazard messages

This document uses the following criteria for hazard messages based on ANSI standards

Z535.6-2011 (R2017).

DANGER

Serious injury or death will occur if a hazardous situation is not avoided.

WARNING

Serious injury or death could occur if a hazardous situation is not avoided.

CAUTION

Minor or moderate injury will or could occur if a hazardous situation is not avoided.

NOTICE

Data loss, property damage, hardware damage, or software damage can occur if a

situation is not avoided. There is no credible risk of physical injury.

Physical access

NOTICE

Unauthorized personnel can potentially cause significant damage and/or misconfiguration

of end users' equipment. Protect against all intentional or unintentional unauthorized use.

Physical security is an important part of any security program and fundamental to

protecting your system. Restrict physical access to protect users' assets. This is true for all

systems used within the facility.

1.3 Related documentation

You can find all product documentation on the product documentation DVD shipped with

the product or at www.emerson.com.

See any of the following documents for more information:

•The hazardous area approvals documentation shipped with the sensor or available at

www.emerson.com/flowmeasurement.

•Micro Motion T-Series Flow and Density Meters Product Data Sheet

Installation Manual Before you begin

20002172 February 2020

Installation Manual 5

•Micro Motion 9-Wire Flowmeter Cable Preparation and Installation Guide

•The transmitter installation and configuration and use guides

Before you begin Installation Manual

February 2020 20002172

6 Micro Motion T-Series

2 Planning

2.1 Installation checklist

□Make sure that the hazardous area specified on the approval tag is suitable for the

environment in which the meter will be installed.

WARNING

Failure to abide by approvals can cause an explosion resulting in injury or death.

□Verify that the local ambient and process temperatures are within the limits of the

meter.

□If your sensor has an integral transmitter, no wiring is required between the sensor and

transmitter. Follow the wiring instructions in the transmitter installation manual for

signal and power wiring.

□If your transmitter has remote-mounted electronics, follow the instructions in this

manual for wiring between the sensor and the transmitter, and then follow the

instructions in the transmitter installation manual for power and signal wiring.

Table 2-1: Maximum cable lengths

Cable type To transmitter Maximum length

Micro Motion

9-wire

9739 MVD and 5700

transmitter

1,000 ft (305 m)

All other MVD transmitters 60 ft (18 m)

Micro Motion

4-wire

All 4-wire MVD transmitters 1,000 ft (305 m) without Ex-approval

500 ft (152 m) with IIC-rated sensors

1,000 ft (305 m) with IIB-rated sensors

Table 2-2: Maximum lengths for user-supplied 4-wire cable

Wire function Wire size Maximum length

Power (VDC) 22 AWG (0.326 mm²) 300 ft (91 m)

20 AWG (0.518 mm²) 500 ft (152 m)

18 AWG (0.823 mm²) 1,000 ft (305 m)

Signal (RS-485) 22 AWG (0.326 mm²) or larger 1,000 ft (305 m)

□For optimal performance, install the sensor in the preferred orientation. The sensor will

work in any orientation as long as the flow tubes remain full of process fluid.

□Install the meter so that the flow direction arrow on the sensor case matches the actual

forward flow of the process. (Flow direction is also software-selectable.)

Installation Manual Planning

20002172 February 2020

Installation Manual 7

2.2 Best practices

The following information can help you get the most from your sensor.

•There are no pipe run requirements for Micro Motion sensors. Straight runs of pipe

upstream or downstream are unnecessary.

•If the sensor is installed in a vertical pipeline, liquids and slurries should flow upward

through the sensor. Gases should flow downward.

•Keep the sensor tubes full of process fluid.

•For halting flow through the sensor with a single valve, install the valve downstream

from the sensor.

•Minimize bending and torsional stress on the meter. Do not use the meter to align

misaligned piping.

•The sensor does not require external supports. The flanges will support the sensor in

any orientation.

2.3 Temperature limits

Sensors can be used in the process and ambient temperature ranges shown in the

temperature limit graphs. For the purposes of selecting electronics options, temperature

limit graphs should be used only as a general guide. If your process conditions are close to

the gray area, consult with your Micro Motion representative.

Note

•In all cases, the electronics cannot be operated where the ambient temperature is

below -40 °F (-40.0 °C) or above 140 °F (60.0 °C). If a sensor is to be used where the

ambient temperature is outside of the range permissible for the electronics, the

electronics must be remotely located where the ambient temperature is within the

permissible range, as indicated by the shaded areas of the temperature limit graphs.

•Temperature limits may be further restricted by hazardous area approvals. Refer to the

hazardous area approvals documentation shipped with the sensor or available at

www.emerson.com/flowmeasurement.

•The extended-mount electronics option allows the sensor case to be insulated without

covering the transmitter, core processor, or junction box, but does not affect

temperature ratings. When insulating the sensor case at elevated process

temperatures above 140 °F (60.0 °C), ensure electronics are not enclosed in insulation

as this may lead to electronics failure.

Planning Installation Manual

February 2020 20002172

8 Micro Motion T-Series

Ambient and process temperature limits for all models

122 (50)

125.5

(52)

140 (60)

-40 (-40)

-60 (–51)

-20 (-29)

20 (7)

60 (16)

100 (38)

-60 (-51)

300 (149)

-20 (-29)

20 (7)

60 (16)

100 (38)

140 (60)

200 (93)

280 (138)

240 (116)

320 (160)

A. Ambient temperature of core processor or transmitter in °F (°C)

B. Maximum process temperature in °F (°C)

C. Mount transmitter remotely and use a junction box

D. Temperature is below -40 °F (-40 °C); mount transmitter remotely and use a junction box

2.4 Recommendations for hygienic and self-

draining applications

For optimal cleanability and drainability:

•If possible, install the sensor in a vertical pipeline with the process fluid flowing upward

through the sensor.

•The minimum angle of inclination of the sensor depends on the process fitting. See

Figure 2-1 and Table 2-3.

•For clean-in-place (CIP) applications, Micro Motion recommends using the generally-

accepted flow velocity of at least 1.5 m/s for cleaning the sensor.

•If the process piping must be larger than the sensor, eccentric reducers may be used to

ensure full drainability. In this case, the process end connections for the piping and

sensor must be the same size. See Figure 2-2.

Note

As part of the cleaning process, you can purge skid-based systems with nitrogen at the

end of the cleaning cycle. When using eccentric reducers, it is possible to trap gas in

the section of process piping adjacent to the reducer. Sensor performance can be

impacted by intermittent flow of the captured gas in a liquid fluid stream.

Installation Manual Planning

20002172 February 2020

Installation Manual 9

•The gap between the electronics housing and sensor body should be inspected

periodically. Manually clean this gap when necessary.

•Tri-Clamp® and DIN 11851 style process connections require special gaskets to comply

with EHEDG requirements for hygienic design.

Figure 2-1: Sensor inclination

A. Angle of inclination

B. Direction of gravity

Table 2-3: Minimum angle of inclination

Model Fitting

code Description Min. angle

T025F, T025T 621 0.5 in (13 mm) Tri-Clamp compatible sanitary

clamp

47°

670 DN10 DIN 11851 sanitary coupling 47°

671 DN15 DIN 11851 sanitary coupling 47°

676 DN15 DIN 11864-1A sanitary coupling 47°

T050F, T050T 621 0.5 in (13 mm) Tri-Clamp compatible sanitary

clamp

0°

671 DN15 DIN 11851 sanitary coupling 47°

676 DN15 DIN 11864-1A sanitary coupling 47°

T075F, T075T 622 0.75 in (19.0 mm) Tri-Clamp compatible sanitary

clamp

0°

623 1 in (25 mm) Tri-Clamp compatible sanitary clamp 47°

662 DN25 ISO 2853 (IDF) sanitary coupling 47°

672 DN25 DIN 11851 sanitary coupling 47°

677 DN25 DIN 11864-1A sanitary coupling 47°

692 DN25 SMS 1145 sanitary coupling 32°

T100F, T100T 623 1 in (25 mm) Tri-Clamp compatible sanitary clamp 0°

Planning Installation Manual

February 2020 20002172

10 Micro Motion T-Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Emerson Zubehör Handbücher

Emerson

Emerson WaterSiren Pro Bedienungsanleitung

Emerson

Emerson ER40 Bedienungsanleitung

Emerson

Emerson Rosemount 3900 Bedienungsanleitung

Emerson

Emerson Rosemount 372 Bedienungsanleitung

Emerson

Emerson Rosemount 499ACL-03 Bedienungsanleitung

Emerson

Emerson Fisher 249W Bedienungsanleitung

Emerson

Emerson Rosemount 499ACL-01 Bedienungsanleitung

Emerson

Emerson Micro Motion 7835 Bedienungsanleitung

Emerson

Emerson Rosemount 499AOZ Bedienungsanleitung

Emerson

Emerson MICRO MOTION T-SERIES Bedienungsanleitung

Emerson

Emerson Rosemount 226 Bedienungsanleitung

Emerson

Emerson 210-2002 Betriebsanleitung

Emerson

Emerson Rosemount 225 Bedienungsanleitung

Emerson

Emerson Rosemountl Bedienungsanleitung

Emerson

Emerson Rosemount 214C Bedienungsanleitung

Emerson

Emerson Rosemount 396PVP Bedienungsanleitung

Emerson

Emerson Fisher 249VS Bedienungsanleitung

Emerson

Emerson Rosemount Hx338+ Bedienungsanleitung

Emerson

Emerson Fisher 249 Bedienungsanleitung

Emerson

Emerson Micro Motion F-Series Sensor Bedienungsanleitung

Emerson

Emerson AVENTICS ST4-2P Bedienungsanleitung

Emerson

Emerson FB1100 Stücklistenhandbuch

Emerson

Emerson ER107001 Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung