Emerson Micro Motion TA Series Bedienungsanleitung

Installation Manual

MMI-20040393, Rev AA

April 2018

Micro Motion® TA-Series Flow and Density

Meters

Safety and approval information

This Micro Motion product complies with all applicable European directives when properly installed in accordance with the

instructions in this manual. Refer to the EU declaration of conformity for directives that apply to this product. The EU declaration of

conformity, with all applicable European directives, and the complete ATEX Installation Drawings and Instructions are available on

the internet at www.emerson.com or through your local Micro Motion support center.

Information affixed to equipment that complies with the Pressure Equipment Directive, can be found on the internet at

www.emerson.com.

For hazardous installations in Europe, refer to standard EN 60079-14 if national standards do not apply.

Other information

Full product specifications can be found in the product data sheet. Troubleshooting information can be found in the configuration

manual. Product data sheets and manuals are available from the Micro Motion web site at www.emerson.com.

Return policy

Follow Micro Motion procedures when returning equipment. These procedures ensure legal compliance with government

transportation agencies and help provide a safe working environment for Micro Motion employees. Micro Motion will not accept

your returned equipment if you fail to follow Micro Motion procedures.

Return procedures and forms are available on our web support site at www.emerson.com, or by phoning the Micro Motion Customer

Service department.

Emerson Flow customer service

Email:

•Worldwide: [email protected]

•Asia-Pacific: [email protected]

Telephone:

North and South America Europe and Middle East Asia Pacific

United States 800-522-6277 U.K. 0870 240 1978 Australia 800 158 727

Canada +1 303-527-5200 The Netherlands +31 (0) 704 136 666 New Zealand 099 128 804

Mexico +41 (0) 41 7686 111 France 0800 917 901 India 800 440 1468

Argentina +54 11 4837 7000 Germany 0800 182 5347 Pakistan 888 550 2682

Brazil +55 15 3413 8000 Italy 8008 77334 China +86 21 2892 9000

Central & Eastern +41 (0) 41 7686 111 Japan +81 3 5769 6803

Russia/CIS +7 495 981 9811 South Korea +82 2 3438 4600

Egypt 0800 000 0015 Singapore +65 6 777 8211

Oman 800 70101 Thailand 001 800 441 6426

Qatar 431 0044 Malaysia 800 814 008

Kuwait 663 299 01

South Africa 800 991 390

Saudi Arabia 800 844 9564

UAE 800 0444 0684

Contents

Chapter 1 Planning ...........................................................................................................................1

1.1 About this document ..................................................................................................................... 1

1.2 Additional documentation and resources .......................................................................................1

1.3 Installation checklist .......................................................................................................................2

1.4 Best practices .................................................................................................................................3

1.5 Temperature limits .........................................................................................................................4

Chapter 2 Mounting .........................................................................................................................5

2.1 Mount the meter ............................................................................................................................5

Chapter 3 Wiring ............................................................................................................................. 6

3.1 Tantalum wiring ............................................................................................................................. 6

Chapter 4 Grounding ........................................................................................................................8

Chapter 5 Pressure relief .................................................................................................................. 9

5.1 Purge the sensor case ...................................................................................................................10

Contents

Installation Manual i

Contents

ii Micro Motion TA Series

1 Planning

Topics covered in this chapter:

•About this document

•Additional documentation and resources

•Installation checklist

•Best practices

•Temperature limits

1.1 About this document

This manual provides information on planning, mounting, and grounding the meter. For

information on full configuration, maintenance, troubleshooting, or service of the

transmitter, see the configuration and use manual.

The information in this document assumes that users understand:

•Basic transmitter and sensor installation, configuration, and maintenance concepts

and procedures

•All corporate, local government, and national government safety standards and

requirements that guard against injuries and death

1.2 Additional documentation and resources

Topic Document

Product Data Sheet Micro Motion Tantalum-Series Meters Product Data Sheet (PDS)

Micro Motion Model 5700 Product Data Sheet (PDS)

Model 5700 installation Micro Motion Model 5700 Transmitters with Configurable Outputs:

Installation Manual

Micro Motion Model 5700 Ethernet Transmitters: Installation Manual

Micro Motion Model 5700 Transmitters with FOUNDATION™ Field-

bus: Installation Manual

Model 5700 configuration Micro Motion Model 5700 Transmitters with Configurable Outputs:

Configuration and Use Manual

Micro Motion Model 5700 Ethernet Transmitters: Configuration and

Use Manual

Micro Motion Model 5700 Transmitters with FOUNDATION™ Field-

bus: Configuration and Use Manual

Modbus TCP configuration Modbus Interface Tool (MIT) — available at www.emerson.com

Planning

Installation Manual 1

Topic Document

Hazardous area installation See the approval documentation shipped with the transmitter, or

download the appropriate documentation at www.emerson.com.

All documentation resources are available at www.emerson.com or on the user

documentation DVD.

1.3 Installation checklist

□Safety messages are provided throughout this content to protect personnel and

equipment. Read each safety message carefully before proceeding to the next step.

□If possible, install the meter in a location that will prevent direct exposure to

sunlight. The environmental limits for the meter may be further restricted by

hazardous area approvals.

□If you plan to mount the meter in a hazardous area:

-Verify that the meter has the appropriate hazardous area approval. Each meter

has a hazardous area approval tag attached to the meter housing.

-For ATEX/IECEx installations, strictly adhere to the safety instructions

documented in the ATEX/IECEx approvals documentation available on the

Product Documentation DVD shipped with the product or at www.emerson.com.

Be sure to reference this documentation in addition to the information shown in

this guide.

□Verify that the local ambient and process temperatures are within the limits of the

meter.

□Follow the wiring instructions in the Model 5700 installation manual for signal and

power wiring.

□Mount the meter in a location and orientation that allows sufficient clearance to

open the housing cover. Allow 8–10 inches (200–250 mm) clearance at the wiring

access points.

□Install the meter so that the flow direction arrow on the sensor case matches the

actual forward flow of the process. Flow direction is also software-selectable.

1.3.1 Orientation options

You can mount the meter in any orientation as long as the conduit openings or display do

not point upward. Keep the sensor tubes full of process fluid to achieve best performance.

CAUTION!

Installing the meter with the conduit openings or display facing upward risks moisture

entering the housing, which could damage the meter.

Planning

2Micro Motion TA Series

Preferred sensor orientationTable 1-1:

Liquids

Gases

Slurries

1.4 Best practices

•There are no pipe run requirements for Emerson meters. Straight runs of pipe

upstream or downstream are unnecessary.

•If the meter is installed in a vertical pipeline, liquids and slurries should flow upward

through the meters. Gases should flow downward.

•Keep the meter tubes full of process fluid.

•For halting flow through the meter with a single valve, install the valve downstream

from the meter.

•Minimize bending and torsional stress on the meter. Do not use the meter to align

misaligned piping.

•The meter does not require external supports. The flanges will support the sensor in

any orientation.

•Do not use the junction box to pick up the meter.

•Do not use the junction box as a step.

•Do not unscrew and rotate the junction box as this will break the wires.

•Do not install the meter in suspended pipes.

•Do not adjust the meter position by pulling or grasping the meter.

Planning

Installation Manual 3

1.5 Temperature limits

Temperature type Min Max

Process temperature -40 ˚F (-40 ˚C) 356 ˚F (180 ˚C)

Ambient temperature -40 ˚F (-40 ˚C) 212 ˚F (100 ˚C)

Use the extended mount junction box (electronic interface code H) for process

temperatures above 212 ˚F (100 ˚C).

Planning

4Micro Motion TA Series

2 Mounting

2.1 Mount the meter

Use your common practices to minimize torque and bending load on process connections.

Prerequisites

Read the installation checklist and best practices if you have not yet done so already. See

Section 1.3 and Section 1.4.

Procedure

Mount the meter using the following illustration.

Mounting

Installation Manual 5

3 Wiring

3.1 Tantalum wiring

•A 9-wire cable is limited to 1000 feet (305 meters) between the sensor and the

transmitter.

•If you are using the Smart Meter Verification (SMV) application, the 9-wire cable is

limited to 60 feet (18 meters) maximum.

•Use Teflon™ jacketed cable for SMV applications.

DANGER!

Make sure the hazardous area specified on the sensor approval tag is suitable for the

environment in which the sensor will be installed. Failure to comply with the requirements for

intrinsic safety in a hazardous area could result in an explosion.

CAUTION!

Fully close and tighten all housing covers and conduit openings. Improperly sealed housings

can expose electronics to moisture, which can cause measurement error or flowmeter failure.

Inspect and grease all gaskets and O-rings.

3.1.1 Connect the 9-wire cable

1. Prepare and install the cable according to the instructions in the Micro Motion 9-

Wire Flowmeter Cable Preparation and Installation Guide.

2. Insert the stripped ends of the individual wires into the terminal blocks of the

junction box. Ensure that no bare wires remain exposed.

Wiring

6Micro Motion TA Series

Andere Handbücher für Micro Motion TA Series

Inhaltsverzeichnis

Andere Emerson Messgerät Handbücher

Emerson

Emerson Rosemount 6888Xi Bedienungsanleitung

Emerson

Emerson FB2100 Bedienungsanleitung

Emerson

Emerson Rosemount Clarity II T56 Bedienungsanleitung

Emerson

Emerson AMS Bedienungsanleitung

Emerson

Emerson Rosemount 928 Bedienungsanleitung

Emerson

Emerson Rosemount X-Stream Series Montage- und Bedienungsanleitung

Emerson

Emerson Rosemount 9295 Bedienungsanleitung

Emerson

Emerson Rosemount 8800D Series Bedienungsanleitung

Emerson

Emerson Rosemount 1595 Bedienungsanleitung

Emerson

Emerson Micro Motion ELITE Bedienungsanleitung

Emerson

Emerson mobrey MSP-USTD1 Bedienungsanleitung

Emerson

Emerson Daniel 3812 Bedienungsanleitung

Emerson

Emerson 2130 RBM Consultant Pro Bedienungsanleitung

Emerson

Emerson EC2-XC645CX Verdrahtungsschema

Emerson

Emerson Micro Motion 782791**B Series Bedienungsanleitung

Emerson

Emerson Rosemount 9195 Bedienungsanleitung

Emerson

Emerson ROSEMOUNT370XA Bedienungsanleitung

Emerson

Emerson AMS 2140 Bedienungsanleitung

Emerson

Emerson Micro Motion SGM Series Kurzanleitung

Emerson

Emerson Rosemount Clarity II T1056 Bedienungsanleitung

Emerson

Emerson Fisher 4320 Bedienungsanleitung

Emerson

Emerson Rosemount WPG Bedienungsanleitung

Emerson

Emerson Rosemount Apex Bedienungsanleitung

Emerson

Emerson Daniel 3410 Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung