Emerson Rosemount 3051 CF Series Bedienungsanleitung

Quick Start Guide

00825-0200-4774, Rev CA

February 2019

Rosemount™ 3051 Pressure Transmitter

and Rosemount 3051CF Series

Flowmeters

with FOUNDATION™ Fieldbus Protocol

Safety messages

NOTICE

This guide provides basic guidelines for Rosemount 3051 Transmitters. It does not provide instructions

for configuration, diagnostics, maintenance, service, troubleshooting, Explosion-proof, Flameproof, or

intrinsically safe (I.S.) installations. Refer to the Rosemount 3051 FOUNDATION Fieldbus Reference

Manual for more instruction. This manual is also available electronically on Emerson.com/Rosemount.

WARNING

Explosions could result in death or serious injury.

Installation of the transmitters in a hazardous environment must be in accordance with the

appropriate local, national, and international standards, codes, and practices. Please review the

Product Certifications section for any restrictions associated with a safe installation.In Explosion-proof/

Flameproof and Non-Incendive/Type n installations, do not remove the transmitter covers when power

is applied to the unit.

Process leaks could result in death or serious injury.

To avoid process leaks, only use the O-ring designed to seal with the corresponding flange adapter.

Electrical shock could cause death or serious injury.

Avoid contact with the leads and terminals. High voltage that may be present on leads can cause

electrical shock.

Conduit/cable entries

Unless marked, the conduit/cable entries in the transmitter housing use a ½–14 NPT thread form.

Entries marked “M20” are M20 × 1.5 thread form. On devices with multiple conduit entries, all entries

will have the same thread form. Only use plugs, adapters, glands, or conduit with a compatible thread

form when closing these entries.

Contents

System readiness........................................... 3

Transmitter installation..................................5

Product Certifications.................................. 27

Quick Start Guide February 2019

2 Emerson.com/Rosemount

1 System readiness

1.1 Confirm correct device driver

•Verify the correct device driver (DD/DTM™) is loaded on your systems to

ensure proper communications.

•Download the correct device driver at your host vendor download site,

Emerson.com/Rosemount or Fieldbus.org.

1.1.1 Rosemount 3051 device revisions and drivers

Table 1-1 provides the information necessary to ensure you have the correct

device driver and documentation for your device.

Table 1-1: Rosemount 3051 FOUNDATION Fieldbus Device Revisions and

Files

Device

Revision(1)

Host Device driver (DD)(2) Device driver

(DTM)

Document

8 All DD4: DD Rev 1 Emerson.com Rosemount

3051 Pressure

Transmitter

with FOUNDATION

Fieldbus

Reference

Manual

All DD5: DD Rev 1

Emerson AMS Device Manager

V 10.5 or higher: DD

Rev 2

Emerson AMS Device Manager

V 8 to 10.5: DD Rev 1

Emerson Field Communicator:

DD Rev 2

7 All DD4: DD Rev 3

All DD5: NA

Emerson AMS Device Manager

V 10.5 or higher: DD

Rev 6

Emerson AMS Device Manager

V 8 to 10.5: DD Rev 4

Emerson Field Communicator:

DD Rev 6

(1) FOUNDATION Fieldbus device revision can be read using a Foundation Fieldbus

capable configuration tool.

(2) Device driver file names use device and DD revision. To access functionality, the

correct device driver must be installed on your control and asset management

hosts, and on your configuration tools.

February 2019 Quick Start Guide

Quick Start Guide 3

Figure 1-1: Installation Flowchart

Start

1. Transmitter

installation

(Section 3)

2. Commissioning

tag

(Section 3.4)

Done

Locate device

7. Zero trim the

transmitter

(Section 5.4)

3. Housing

rotation

(Section 3.5.1)

5. Grounding,

wiring and

power up

(Section 4.6)

6. Configuration

(Section 2.7.1, 2.8)

4. Set switches

and software

write lock

(Section 4.4)

Quick Start Guide February 2019

4 Emerson.com/Rosemount

2 Transmitter installation

2.1 Mount the transmitter

For dimensional drawing information refer to the Dimensional Drawings

section of the Rosemount™ 3051 Product Data Sheet.

Figure 2-1: Panel Mount Coplanar Flange

5/16 x 1½ panel bolts are customer supplied.

February 2019 Quick Start Guide

Quick Start Guide 5

Figure 2-2: Pipe Mount Coplanar Flange

Figure 2-3: Panel Mount Traditional Flange

Figure 2-4: Pipe Mount Traditional Flange

Quick Start Guide February 2019

6 Emerson.com/Rosemount

Figure 2-5: Panel Mount Rosemount™ 3051T

Figure 2-6: Pipe Mount Rosemount 3051T

2.1.1 Mount the transmitter in liquid applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Mount the transmitter so the drain/vent valves are oriented upward.

Figure 2-7: Mounting the Transmitter in Liquid Applications

Coplanar In-line

February 2019 Quick Start Guide

Quick Start Guide 7

Flow

2.1.2 Mount the transmitter in gas applications

Procedure

1. Place taps in the top or side of the line.

2. Mount beside or above the taps.

Figure 2-8: Mounting the Transmitter in Gas Applications

Coplanar Inline

Flow

2.1.3 Mount the transmitter in steam applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Fill impulse lines with water.

Quick Start Guide February 2019

8 Emerson.com/Rosemount

Figure 2-9: Mounting the Transmitter in Steam Applications

Coplanar In-line

Flow

2.1.4 Bolting considerations

If the transmitter installation requires assembly of the process flanges,

manifolds, or flange adapters, follow these assembly guidelines to ensure a

tight seal for optimal performance characteristics of the transmitters. Use

only bolts supplied with the transmitter or sold by Emerson as spare parts.

Figure 2-10 illustrates common transmitter assemblies with the bolt length

required for proper transmitter assembly.

Figure 2-10: Common Transmitter Assemblies

4 × 2.88-in. (73 mm)

4 × 1.75-in. (44 mm)

4 ×1.75-in.

(44 mm) 4 ×1.75-in.

(44 mm)

4 × 1.75-in. (44 mm)

4 × 2.25-in. (57 mm)

A. Transmitter with coplanar flange

B. Transmitter with coplanar flange and optional flange adapters

C. Transmitter with traditional flange and optional flange adapters

D. Transmitter with coplanar flange and optional manifold and flange

adapters

Bolts are typically carbon steel (CS) or stainless steel (SST). Confirm the

material by viewing the markings on the head of the bolt and referencing

February 2019 Quick Start Guide

Quick Start Guide 9

Table 2-1. If bolt material is not shown in Table 2-1, contact a local Emerson

representative for more information.

Procedure

1. Carbon steel bolts do not require lubrication and the stainless steel

bolts are coated with a lubricant to ease installation. However, no

additional lubricant should be applied when installing either type of

bolt.

2. Finger-tighten the bolts.

3. Torque the bolts to the initial torque value using a crossing pattern.

See Table 2-1 for initial torque value.

4. Torque the bolts to the final torque value using the same crossing

pattern. See Table 2-1 for final torque value.

5. Verify the flange bolts are protruding through the isolator plate before

applying pressure.

Example

Table 2-1: Torque Values for the Coplanar Flange and Flange Adapter

Bolts

Bolt material Head markings Initial

torque

Final

torque

B7M

300 in-lb 650 in-lb

SST

316

STM

316

B8M

150 in-lb 300 in-lb

Quick Start Guide February 2019

10 Emerson.com/Rosemount

Andere Handbücher für Rosemount 3051 CF Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Emerson Messgerät Handbücher

Emerson

Emerson Rosemount 5400 Series Bedienungsanleitung

Emerson

Emerson Rosemount 2051 Wireless Series Bedienungsanleitung

Emerson

Emerson Rosemount BINOS 100 F Bedienungsanleitung

Emerson

Emerson Rosemount Analytical CAT 100 Bedienungsanleitung

Emerson

Emerson FloBoss 103 Bedienungsanleitung

Emerson

Emerson FloBoss 103 Kurzanleitung

Emerson

Emerson Rosemount 8800D Series Benutzerhandbuch

Emerson

Emerson E2 Bedienungsanleitung

Emerson

Emerson Daniel 3812 Bedienungsanleitung

Emerson

Emerson mobrey MSP-USTD1 Bedienungsanleitung

Emerson

Emerson Daniel 3410 Series Bedienungsanleitung

Emerson

Emerson Mobrey Hydratect 2462 Bedienungsanleitung

Emerson

Emerson Rosemount 928 Bedienungsanleitung

Emerson

Emerson Daniel Ultrasonic 3410 Series Bedienungsanleitung

Emerson

Emerson Daniel Series Bedienungsanleitung

Emerson

Emerson Rosemount Oxymitter DR Bedienungsanleitung

Emerson

Emerson Wireless Field Link Bedienungsanleitung

Emerson

Emerson Rosemount 56 Bedienungsanleitung

Emerson

Emerson X-STREAM XE Bedienungsanleitung

Emerson

Emerson Rosemount 8800D Series Bedienungsanleitung

Emerson

Emerson Rosemount 1154DH Bedienungsanleitung

Emerson

Emerson Rosemount 8750WB Bedienungsanleitung

Emerson

Emerson Daniel PT Bedienungsanleitung

Emerson

Emerson Rosemount WPG Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung