Emerson Rosemount 485 Annubar Bedienungsanleitung

Quick Start Guide

00825-0400-4809, Rev FB

June 2016

Rosemount™485 Annubar™Flanged

Flo-Tap Assembly

00825-0400-4809 Rev FB.fm Page 1 Thursday, June 16, 2016 1:16 PM

June 2016

Quick Start Guide

NOTICE

This guide provides basic guidelines for Rosemount 485 Annubar. It does not provide instructions for

configuration, diagnostics, maintenance, service, troubleshooting, Explosion-proof, Flameproof, or

Intrinsically Safe (I.S.) installations. Refer to the Rosemount 485 Annubar Reference Manual for more

instruction. This manual is also available electronically on EmersonProcess.com/Rosemount.

If the Rosemount Annubar was ordered assembled to a Rosemount Pressure Transmitter, see the following

Quick Start Guides for information on configuration and hazardous locations certifications:

Rosemount 3051S Series Pressure Transmitter and Rosemount 3051SF Series Flowmeter Quick Start

Guide.

Rosemount 3051S MultiVariable Transmitter and Rosemount 3051SF Series Flowmeter MultiVariable

Transmitter Quick Start Guide.

Rosemount 3051 Pressure Transmitter and Rosemount 3051CF Series Flowmeter Transmitter Quick

Start Guide.

Rosemount 2051 Pressure Transmitter and Rosemount 2051CF Series Flowmeter Transmitter Quick

Start Guide.

Process leaks may cause harm or result in death. To avoid process leaks, only use gaskets designed to seal

with the corresponding flange and O-rings to seal process connections. Flowing medium may cause the

Rosemount 485 Annubar Assembly to become hot and could result in burns.

Contents

Location and orientation . . . . . . . . . . . . . . . . . 4

Weld mounting hardware . . . . . . . . . . . . . . . . 8

Install isolation valve . . . . . . . . . . . . . . . . . . . . . 9

Mount drilling machine and drill hole . . . . .10

Remove drilling machine . . . . . . . . . . . . . . . .10

Mount the Rosemount Annubar Assembly . . . .11

Insert the Rosemount Annubar Sensor . . . . . . .12

Mount the Transmitter . . . . . . . . . . . . . . . . . . . . . 13

Retracting the Rosemount Annubar Assembly 17

Product certifications . . . . . . . . . . . . . . . . . . . . . 18

00825-0400-4809 Rev FB.fm Page 2 Thursday, June 16, 2016 1:16 PM

Quick Start Guide

June 2016

Figure 1. Rosemount 485 Annubar Flanged Flo-Tap Assembly Exploded View

Note

Use an appropriate pipe sealing compound rated for the service temperature on all

threaded connections.

A. Transmitter I. Isolation valve

B. 2⫻O-rings J. Cage nipple

C. Temperature sensor connection housing K. Support plate

D. Direct mount transmitter connection with valves L. Packing gland

E. Head plate M. Packing

F. Drive rods N. Follower

G. Mounting flange assembly O. Compression plate

H. Gasket P. Coplanar flange with drain vents

00825-0400-4809 Rev FB.fm Page 3 Thursday, June 16, 2016 1:16 PM

June 2016

Quick Start Guide

1.0 Location and orientation

Correct orientation and straight run requirements must be met for accurate and

repeatable flow measurements. Refer to Table 1for minimum pipe diameter

distances from upstream disturbances.

Table 1. Straight Run Requirements

In plane____________Out of plane Upstream pipe diameters

Downstream

pipe diameters

Without

straightening

vanes

With straightening

vanes

plane

Outof

plane

A’ CC’ B

N/A

00825-0400-4809 Rev FB.fm Page 4 Thursday, June 16, 2016 1:16 PM

Quick Start Guide

June 2016

Note

Consult the factory for instructions regarding use in square or rectangular

ducts.

“In plane A” means the bar is in the same plane as the elbow. “Out of plane A”

means the bar is perpendicular to the plane of the elbow.

If proper lengths of straight run are not available, position the mounting such

that 80% of the run is upstream and 20% is downstream.

Use straightening vanes to reduce the required straight run length.

Row 6 in Table 1 applies to gate, globe, plug, and other throttling valves that

are partially opened, as well as control valves.

1.1 Misalignment

Rosemount 485 Annubar installation allows for a maximum misalignment of 3°.

Figure 2. Misalignment

N/A

+3+3

00825-0400-4809 Rev FB.fm Page 5 Thursday, June 16, 2016 1:16 PM

June 2016

Quick Start Guide

1.2 Horizontal orientation

For proper venting and draining, the sensor should be located in the upper half of

the pipe for air and gas applications. For liquid and steam applications, the sensor

should be located in the bottom half of the pipe. The maximum temperature for a

direct mounted transmitter is 500 °F (260 °C). See “Install isolation valve” on

page 9 for remote mounted transmitter recommendations.

Figure 3. Gas

Figure 4. Liquid and Steam

Note

For steam applications with DP readings between 0.75 and 2 inH2O in horizontal pipes, it is

recommended to install the primary element/flowmeter mounting above the pipe.

Recommended zone

00825-0400-4809 Rev FB.fm Page 6 Thursday, June 16, 2016 1:16 PM

Quick Start Guide

June 2016

Note

Due to the weight of the Flo-Tap mounting hardware, external support may be needed for

vertical orientation applications and horizontal orientation applications that are installed

outside of the recommended zones.

1.3 Vertical orientation

The sensor can be installed in any position around the circumference of the pipe,

provided the vents are positioned properly for bleeding or venting. Optimal

results for liquid or steam are obtained when flow is up. For steam applications, a

90° spacer will be added to provide water legs to ensure the transmitter stays

within temperature limits. The maximum temperature for a direct mounted

transmitter is 500 °F (260 °C).

Figure 5. Steam

Figure 6. Liquid

Figure 7. Gas

360

Flow

360

Flow

360

Flow

00825-0400-4809 Rev FB.fm Page 7 Thursday, June 16, 2016 1:16 PM

June 2016

Quick Start Guide

2.0 Weld mounting hardware

Note

Rosemount-supplied mounting has an integral alignment built into the mounting hardware

that assists in the correct drilling of the mounting hole. It also assists in the alignment of the

sensor to the mounting hole for insertion.

1. At the pre-determined position, place the flanged assembly on the pipe, gap

1/16-in. (1.6 mm), and measure the distance from the outer diameter of the

pipe to the face of the flange. Compare this toTable 2 and adjust the gap as

necessary.

Table 2. Flange Sizes and Outer Diameter to Flange (ODF) per Sensor Size

Sensor size Flange size ODF (in. [mm]) Flange size ODF (in. [mm])

1 11/2-in. 150# 3.88 (98,5) DN40 PN16 3.09 (78,6)

1 11/2-in. 300# 4.13 (104,9) DN40 PN40 3.21 (81,6)

1 11/2-in. 600# 4.44 (112,7) DN40 PN100 3.88 (98,6)

1 11/2-in. 900# 4.94 (125,4) N/A N/A

1 11/2-in. 1500# 4.94 (125,4) N/A N/A

1 11/2-in. 2500# 6.76 (171,6) N/A N/A

22.0-in. 150# 4.13 (104,8) DN50 PN16 3.40 (86,3)

22.0-in. 300# 4.38 (111,2) DN50 PN40 3.51 (89,3)

22.0-in. 600# 4.76 (120,8) DN50 PN100 4.30 (109,3)

22.0-in. 900# 5.88 (149,2) N/A N/A

22.0-in. 1500# 5.88 (149,2) N/A N/A

23.0-in. 2500# 9.87 (250,7) N/A N/A

33.0-in. 150# 4.63 (117,5) DN80 PN16 3.84 (97,6)

33.0-in. 300# 5.00 (126,9) DN80 PN40 4.16 (105,6)

33.0-in. 600# 5.38 (136,6) DN80 PN100 4.95 (125,6)

34.0-in. 900# 8.19 (208,0) N/A N/A

34.0-in. 1500# 8.56 (217,5) N/A N/A

34.0-in. 2500# 11.19 (284,2) N/A N/A

00825-0400-4809 Rev FB.fm Page 8 Thursday, June 16, 2016 1:16 PM

Quick Start Guide

June 2016

2. Place four 1/4-in. (6 mm) tack welds at 90° increments. Check alignment of the

mounting both parallel and perpendicular to the axis of flow (see Figure 8). If

alignment of the mounting is within tolerances, finish weld per local codes. If

outside of specified tolerance, make adjustments prior to making the finish

weld.

Figure 8. Alignment

A. ODF

B. Tack welds

3. To avoid serious burns, allow the mounting hardware to cool before

continuing.

3.0 Install isolation valve

1. Position the isolation valve onto the mounting flange. Ensure the valve stem is

positioned so that when the Flo-Tap is installed, the insertion rods will straddle

the pipe and the valve handle will be centered between the rods (see Figure 9).

Note

Interference will occur if the valve is located inline with the rods.

2. Fasten the isolation valve to the mounting using gasket, bolts, and nuts.

Figure 9. Isolation Valve Orientation

A. Isolation valve

00825-0400-4809 Rev FB.fm Page 9 Thursday, June 16, 2016 1:16 PM

June 2016

Quick Start Guide

4.0 Mount drilling machine and drill hole

Drilling machine is not provided with assembly.

1. Determine the sensor size based on the sensor width (see Table 3).

Table 3. Sensor Size/Hole Diameter Chart

2. Mount the drilling machine to the isolation valve.

A. Isolation valve is fully open when inserting drill

B. Pressure drilling machine

C. Isolation valve is fully closed after withdrawing drill

3. Open the valve fully.

4. Drill the hole into the pipe wall in accordance with the instructions provided

by the drilling machine manufacturer (use Table 3 to select the proper drill bit

for the sensor being used).

5. Retract the drill fully beyond the valve.

5.0 Remove drilling machine

1. Verify the drill has been retracted past the valve.

2. Close the isolation valve to isolate the process.

3. Bleed drilling machine pressure and remove.

4. Check isolation valve and mounting for leakage.

Sensor size Sensor width Hole diameter

10.590-in. (14,99 mm) 3/4-in. (19 mm) +1/32-in (0,8 mm) – 0.00

21.060-in. (26,92 mm) 15/16-in. (34 mm) +1/16-in. (1,6 mm) – 0.00

31.935-in. (49,15 mm) 21/2-in. (64 mm) +1/16-in. (1,6 mm) – 0.00

00825-0400-4809 Rev FB.fm Page 10 Thursday, June 16, 2016 1:16 PM

Andere Handbücher für Rosemount 485 Annubar

Inhaltsverzeichnis

Andere Emerson Messgerät Handbücher

Emerson

Emerson Rosemount Oxymitter DR Bedienungsanleitung

Emerson

Emerson Rosemount 3410 Series Programmierhandbuch

Emerson

Emerson Rosemount 3051SF Series Bedienungsanleitung

Emerson

Emerson Fisher 4320 Bedienungsanleitung

Emerson

Emerson Clarity II Bedienungsanleitung

Emerson

Emerson Daniel 3415 Bedienungsanleitung

Emerson

Emerson Aventics R412018223 Bedienungsanleitung

Emerson

Emerson PENBERTHY LC Series Handbuch

Emerson

Emerson RXi HMI Bedienungsanleitung

Emerson

Emerson Lumity IC100D EVO Bedienungsanleitung

Emerson

Emerson Daniel PT Series Bedienungsanleitung

Emerson

Emerson X-STREAM Series Bedienungsanleitung

Emerson

Emerson mobrey MSP-USTD1 Bedienungsanleitung

Emerson

Emerson Rosemount 753R Bedienungsanleitung

Emerson

Emerson Micro Motion CDM100M A Series Kurzanleitung

Emerson

Emerson Rosemount 3300 Series Bedienungsanleitung

Emerson

Emerson FB2100 Bedienungsanleitung

Emerson

Emerson RTM-ATCA-736x-DD Bedienungsanleitung

Emerson

Emerson Rosemount Analytical X-STREAM X2 Series Bedienungsanleitung

Emerson

Emerson Rosemount 9195 Bedienungsanleitung

Emerson

Emerson Rosemount 5408 Bedienungsanleitung

Emerson

Emerson LMS1000 Bedienungsanleitung

Emerson

Emerson Fisher 4320 Konfigurationshandbuch

Emerson

Emerson Rosemount Wireless Permasense WT210 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung