Emerson RTM-ATCA-736x-DD Bedienungsanleitung

RTM-ATCA-736x-DD

Quick Start Guide

P/N:6806800P33A (May 2012)

Observe ESD-safe

measures

What’s in the box?

When installing or servicing the

module or accessories, strictly

observe the safety precautions

in the Safety Notes. Otherwise,

personal injury or property dam-

age may occur. Ignoring these

instructions can void the board

warranty.

Electrostatic discharge and

incorrect RTM installation and

removal can damage circuits or

shorten their life.

• Use either a properly grounded ESD

wrist strap or make sure that you are

working in an ESD-safe environ-

ment.

• Connect to the ESD connector at the

front or the rear of the system.

Make sure you receive all items of

your shipment:

• RTM-ATCA-736x-DD blade

• Other items that were ordered

• Printed Safety Notes Prepare the installation

site

• For information on the environmen-

tal and power requirements, see the

RTM-ATCA-736x-DD Installation and

Use manual.

• Operating temperatures refer to the

temperature of the air circulating

around the blade and not to the

actual component temperature.

RTM-ATCA-736x-DD Quick Start Guide

Emerson Network Power – Embedded Computing

2900 South Diablo Way, Suite 190

Tempe, AZ 85282-3222

USA

Emerson Network Power – Embedded Computing

Lilienthalstr. 15

D-85579 Neubiberg/München

Germany

Emerson Trading (Shanghai) Ltd.

15/F Gateway Building No.

10 Ya Bao Road, Chao Yang Dist.

Beijing 100020

China

Emerson Network Power – Embedded Computing

Shiba Excellent Building 5F

2-1-13 Hamamatsucho, Minato-ku

Tokyo 1 05-0013

Japan

Install the hard disk module

1. Remove the HDD slot cover of the RTM

by loosening and removing the screws

that attach the plate to the RTM.

2. Place the hard disk insulator on the top

of the SAS-PCB assembly . (Find #1 & 8)

3. Align the insulator holes with the holes

on the board.

4. Place the hard disk on the top of the

insulator, such that it is aligned with the

board SATA connector. (Find #9)

5. Slide the hard disk into the SATA connec-

tor.

6. Flip assembly on its back and align the

SAS-PCB holes with the insulator and

hard disk holes.

7. Attach the drive support bracket to the

side of the hard disk. (Find #4)

8. Install the four flat head screws to secure

the drive support bracket to the hard

disk. (Find #5)

9. Install the two pan head screws to fix the

hard disk, insulator, and SAS-PCB

together. (Find #6)

10.Assemble the front panel bezel to the

disk drive assembly using two flat head

screws. (Find #3)

11.Take all necessary steps in your operat-

ing system to make the hard disk opera-

ble (the steps depend on the OS you are

using).

8 4306883A01 A SPACER, HDD MODULE 1 -

6 0306868A01 SCREW, M3x0.5x5, PH 2 -

5 03SL992G30A SCREW, M3x0.5x5, FH 6 -

4 0706823C01 B BRACKET, DRIVE SUPPORT, SAS, HDD-FRU 1 -

3 1306804A01 D BEZEL, MACHINED, SAS, HDD-FRU 1 -

2 88068XXX* HDD 1 -

1 8406880J0** SAS-PCB 1 -

ITEM PART NUMBER DESCRIPTION QTY SUPPLIER

RTM-ATCA-736x-DD Quick Start Guide

Emerson Network Power – Embedded Computing

2900 South Diablo Way, Suite 190

Tempe, AZ 85282-3222

USA

Emerson Network Power – Embedded Computing

Lilienthalstr. 15

D-85579 Neubiberg/München

Germany

Emerson Trading (Shanghai) Ltd.

15/F Gateway Building No.

10 Ya Bao Road, Chao Yang Dist.

Beijing 100020

China

Emerson Network Power – Embedded Computing

Shiba Excellent Building 5F

2-1-13 Hamamatsucho, Minato-ku

Tokyo 1 05-0013

Japan

Install the RTM

1. Locate the slot the RTM is to be

installed into the shelf's rear which

must be the same as that of the front

blade.

2. Ensure that the top and the bottom

handles of the RTM are in an out-

ward position by squeezing the lever

and the latch together.

3. Insert the RTM into the shelf by plac-

ing the top and bottom edges in the

card guides of the slot.

4. Slide the RTM into the slot.

5. Apply equal and steady pressure to

the RTM to carefully slide the RTM

into the shelf until you feel resis-

tance. Continue to gently push the

RTM until the RTM connectors

engage.

Install the RTM (Cont.)5

6. Squeeze the lever and the latch

together and hook the lower and the

upper handle into the shelf rail

recesses.

7. Fully insert the RTM and lock it to the

shelf by pressing the two compo-

nents of the lower and the upper

handles together and turning the

handles toward the face plate.

8. Tighten both face plate screws on

the RTM.

9. Wait until the blue LED on the RTM is

OFF.

A switched off blue LED indicates

that the payload of the RTM has

become active.

10.Plug interface cable into face plate

connectors, if applicable.

11.Reboot the front blade.

This is necessary so that the OS of

the front blade can recognize the

SAS controller or any other PCI

device located on the RTM.

Finding more information

For more information on the product, see

the RTM-ATCA-736x-DD Installation and Use

and other related documentation.

Visit our Web site http://www.emersonnet-

workpower.com/embeddedcomputing.

Use the Product Search link to look for tech-

nical documentation.

Technical Assistance

To request technical assistance, visit our

Web site http://crcportal.emerson.com.

Andere Emerson Messgerät Handbücher

Emerson

Emerson Daniel 3818 Bedienungsanleitung

Emerson

Emerson Rosemount 2051CF series Bedienungsanleitung

Emerson

Emerson ControlWave XFC Bedienungsanleitung

Emerson

Emerson FB1100 Bedienungsanleitung

Emerson

Emerson Rosemount 8800D Series Bedienungsanleitung

Emerson

Emerson Rosemount 3814 Programmierhandbuch

Emerson

Emerson Rosemount 928 Bedienungsanleitung

Emerson

Emerson Rosemount 485 Annubar Bedienungsanleitung

Emerson

Emerson Daniel 3818 Programmierhandbuch

Emerson

Emerson Rosemount 751 Bedienungsanleitung

Emerson

Emerson EC2-XC645CX Verdrahtungsschema

Emerson

Emerson 8800C Bedienungsanleitung

Emerson

Emerson Rosemount Analytical CAT 100 Bedienungsanleitung

Emerson

Emerson Rosemount Wireless Pressure Gauge Bedienungsanleitung

Emerson

Emerson Rosemount 8750WB Bedienungsanleitung

Emerson

Emerson CSI 2140 Bedienungsanleitung

Emerson

Emerson Micro Motion FDM Bedienungsanleitung

Emerson

Emerson Rosemount 1056 Bedienungsanleitung

Emerson

Emerson Fisher 4320 Bedienungsanleitung

Emerson

Emerson Micro Motion 782791**B Series Bedienungsanleitung

Emerson

Emerson Rosemount Clarity II T56 Bedienungsanleitung

Emerson

Emerson Rosemount 485 Annubar Bedienungsanleitung

Emerson

Emerson Rosemount FCL Bedienungsanleitung

Emerson

Emerson NGA2000 TO2 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung