Emerson Rosemount 585 Annubar Bedienungsanleitung

www.rosemount.com

¢00825-0100-4809[¤

Quick Installation Guide

00825-0100-4585, Rev AA

January 2009 Flanged 585 Annubar

Step 1: Location and Orientation

Step 2: Drill Holes into Pipe

Step 3: Assemble and Check Fit-up

Step 4: Weld Mounting Hardware

Step 5: Insert the Annubar

Step 6: Mount the Transmitter

Product Certifications

Start

End

Rosemount 585 Annubar®Flanged Assembly

4585_QIG_AA.fm Page 1 Monday, January 19, 2009 11:18 AM

Quick Installation Guide

00825-0100-4585, Rev AA

January 2009

Flanged 585 Annubar

registered trademarks of Rosemount Inc.

Rosemount Inc.

8200 Market Boulevard

Chanhassen, MN USA 55317

T (US) (800) 999-9307

T (Intnl) (952) 906-8888

F (952) 949-7001

Emerson Process Management GmbH & Co. OHG

Argelsrieder Feld 3

82234 Wessling

Germany

T 49 (8153) 9390

F49 (8153) 939172

Emerson Process Management Asia Pacific

Private Limited

1 Pandan Crescent

Singapore 128461

T (65) 6777 8211

F (65) 6777 0947/65 6777 0743

Beijing Rosemount Far East Instrument Co.,

Limited

No. 6 North Street,

Hepingli, Dong Cheng District

Beijing 100013, China

T (86) (10) 6428 2233

F (86) (10) 6422 8586

IMPORTANT NOTICE

This installation guide provides basic guidelines for Rosemount

585 Annubar. It does not provide instructions for configuration, diagnostics, maintenance,

service, troubleshooting, Explosion-proof, Flame-Proof, or intrinsically safe (I.S.)

installations. Refer to the 585 Annubar reference manual (document number

00809-0100-4585) for more instruction. This manual is also available electronically on

www.rosemount.com.

If the 585 Annubar was ordered assembled to a Rosemount 3051S transmitter, see the

following Quick Installation Guide for information on configuration and hazardous

locations certifications: Rosemount 3051S Series Pressure Transmitter (document

number 00825-0100-4801).

If the 585 Annubar was ordered assembled to a Rosemount 3095 transmitter, see the

following Quick Installation Guide for information on configuration and hazardous

locations certifications: Rosemount 3095MV (document number 00825-0100-4716).

WARNING

Process leaks may cause harm or result in death. To avoid process leaks, only use

gaskets designed to seal with the corresponding flange and o-rings to seal process

connections. Flowing medium may cause the 585 Annubar assembly to become hot and

could result in burns.

CAUTION

If pipe/duct wall is less than 0.125-in. (3,2 mm) use extreme caution when installing

sensor. Thin walls can deform during welding, installation or from the weight of a

cantilevered flowmeter. These installations may require a fabricated outlet, saddle or

external flowmeter support. Please consult factory for assistance.

4585_QIG_AA.fm Page 2 Monday, January 19, 2009 11:18 AM

Quick Installation Guide

00825-0100-4585, Rev AA

January 2009 Flanged 585 Annubar

585 Annubar®Assembly Exploded View

NOTE

Use an appropriate pipe sealing compound rated for the service temperature on all threaded

connections.

Sensor Flange

585 Annubar Sensor

Mounting Flange Assembly

Remote Mount Instrument

Connection

Studs

Gasket

Opposites Side Support

Nuts

4585_QIG_AA.fm Page 3 Monday, January 19, 2009 11:18 AM

Quick Installation Guide

00825-0100-4585, Rev AA

January 2009

Flanged 585 Annubar

STEP 1: LOCATION AND ORIENTATION

Correct orientation and straight run requirements must be met for accurate and repeatable

flow measurements. Refer to Table 1 for minimum pipe diameter distances from upstream

disturbances.

Table 1. Straight Run Requirements

Upstream Dimensions

Downstream

Dimensions

Without

Straightening

Vanes

With Straightening

Vanes

Plane

Out of

Plane

A’ CC’A A

—

4585_QIG_AA.fm Page 4 Monday, January 19, 2009 11:18 AM

Quick Installation Guide

00825-0100-4585, Rev AA

January 2009 Flanged 585 Annubar

STEP 1 CONTINUED...

NOTE

• Consult the factory for instructions regarding use in square or rectangular ducts.

• “In Plane A” means the sensor is in the same plane as the elbow. “Out of Plane A”

means the bar is perpendicular to the plane of the elbow.

• If proper lengths of straight run are not available, position the mounting such that 80%

of the run is upstream and 20% is downstream.

• Use straightening vanes to reduce the required straight run length.

• Row 6 in Table 1 applies to gate, globe, plug, and other throttling valves that are

partially opened, as well as control valves.

Misalignment

585 Annubar installation allows for a maximum misalignment of 3°.

Figure 1. Misalignment

Upstream Dimensions

Downstream

Dimensions

Without Vanes With Vanes

Plane

Out of

Plane

A’ CC’A A

—

±3°

4585_QIG_AA.fm Page 5 Monday, January 19, 2009 11:18 AM

Quick Installation Guide

00825-0100-4585, Rev AA

January 2009

Flanged 585 Annubar

STEP 1 CONTINUED...

Horizontal Orientation

For proper venting and draining, the sensor should be located in the upper half of the pipe

for gas applications. For liquid and steam applications, the sensor should be located in the

bottom half of the pipe.

Figure 2. Gas Figure 3. Liquid and Steam

Figure 4. Steam on Top

45°45°

Recommended

Zone 90°

30° Recommended

Zone 30°

Recommended

Zone 30°

45° 45°

30° Recommended

Zone 30°

Recommended

Zone 30°

45° 45°

4585_QIG_AA.fm Page 6 Monday, January 19, 2009 11:18 AM

Quick Installation Guide

00825-0100-4585, Rev AA

January 2009 Flanged 585 Annubar

STEP 1 CONTINUED...

Vertical Orientation

The sensor can be installed in any position around the circumference of the pipe, provided

the vents are positioned properly for bleeding or venting. Optimal results for liquid or steam

are obtained when flow is up. For steam applications, a 90° spacer is included to provide

water legs to ensure the transmitter stays within temperature limits.

Figure 5. Liquid, Gas, or Steam

360°

Flow

4585_QIG_AA.fm Page 7 Monday, January 19, 2009 11:18 AM

Quick Installation Guide

00825-0100-4585, Rev AA

January 2009

Flanged 585 Annubar

STEP 2: DRILL HOLES INTO PIPE

1. Determine the sensor size based on the probe width (see Table 2).

2. Depressurize and drain the pipe.

3. Select the location to drill the hole.

4. Determine the diameter of the hole to be drilled according to the specifications in Table 2.

Drill the mounting hole into the pipe with a hole saw or drill. DO NOT TORCH CUT THE

HOLE.

Table 2. Sensor Size / Hole Diameter Chart

5. A second identically sized hole must be drilled opposite the first hole so that the sensor

can pass completely through the pipe. To drill the second hole, follow these steps:

a. Measure the pipe circumference with a pipe tape, soft wire, or string. (For the most

accurate measurement the pipe tape needs to be perpendicular to the axis of flow.)

b. Divide the measured circumference by two to determine the location of the second

hole.

c. Re-wrap the pipe tape, soft wire, or string from the center of the first hole. Then, using

the number calculated in the preceding step, mark the center of what will become the

second hole.

d. Using the diameter determined in step 3, drill the hole into the pipe with a hole saw or

drill. DO NOT TORCH CUT THE HOLE.

6. Deburr the drilled holes on the inside of the pipe.

Sensor

Size Sensor Width Hole Diameter

11 0.80-in. (20,32 mm) 7/8-in. (23 mm) + 1/32-in (0,8 mm)

– 0.00

22 1.20-in. (30,48 mm) 15/16-in. (34 mm) + 1/16-in. (1,6 mm)

– 0.00

44 2.30-in. (58,42 mm) 21/2-in. (64 mm) + 1/16-in. (1,6 mm)

– 0.00

Drill the appropriate diameter

hole through the pipe wall.

Note: Drill the hole 180° from

the first hole for opposite- side

support models.

4585_QIG_AA.fm Page 8 Monday, January 19, 2009 11:18 AM

Quick Installation Guide

00825-0100-4585, Rev AA

January 2009 Flanged 585 Annubar

STEP 3: ASSEMBLE AND CHECK FIT-UP

For accurate measurement, use the following steps to ensure that Ports A and B are equal

distances from the inside walls of the pipe.

1. Assemble the 585 to the mounting hardware with the gaskets and bolts.

2. Hand tighten the bolts just enough to hold the position of the sensor centered in the

mounting hardware.

3. Check the fit of the assembly to the pipe by inserting a rule or stiff wire through both

mounting holes. Note the distance. All sensing holes must be inside the pipe inner

diameter. See Figure 6.

4. Add 1/16-in. (1,6 mm) to the measured distance for the weld gap and transfer to the

assembly starting at the high point of the weldolet.

5. Measure the distance from the high point of the weldolet to the first sensing hole, port B,

then subtract 1/16-in (1,6 mm).

6. Measure the distance from the end of the transferred length in step 4 to the last sensing

hole, port A.

7. Compare the numbers obtained in steps 5 and 6.

Small discrepancies can be compensated for with the fit-up of the mounting hardware. Large

discrepancies may cause installation problems or error.

Figure 6. Fit-up check for 585 Annubar with Opposite-Side Support

ODF

Port B

Port A

Pipe

Outside

Diameter

The same within 1/8-in. (3 mm)

4585_QIG_AA.fm Page 9 Monday, January 19, 2009 11:18 AM

Quick Installation Guide

00825-0100-4585, Rev AA

January 2009

Flanged 585 Annubar

STEP 4: WELD MOUNTING HARDWARE

1. Center the flanged assembly over the mounting hole, gap 1/16 in. (1,6 mm), and measure

the distance from the outer diameter of the pipe to the face of the flange. Compare this to

Table 3 and adjust the gap as necessary.

Table 3. Flange Sizes and ODF Per Sensor Size

Sensor Size Flange Type Pressure Class Flange Size / Rating / Type ODF in. (mm)(1)

(1) Tolerances for the ODF dimension above a 10-in. (254 mm) line size is ±0.060-in. (1,6 mm). Below

10-in. (254 mm) line size is ±0.030-in. (0,8 mm).

1/2-in. 150# RF 3.88 (99)

11 3 11/2-in. 300# RF 4.13 (105)

11 6 11/2-in. 600# RF 4.44 (113)

11 N 11/2-in. 900# RF 4.94 (125)

11 F 11/2-in. 1500# RF 4.94 (125)

11 T 11/2-in. 2500# RF 6.76 (172)

1/2-in. 150# RTJ 4.07 (103)

11 3 11/2-in. 300# RTJ 4.32 (110)

11 6 11/2-in. 600# RTJ 4.44 (113)

11 N 11/2-in. 900# RTJ 4.94 (125)

11 F 11/2-in. 1500# RTJ 4.94 (125)

11 T 11/2-in. 2500# RTJ 6.82 (173)

1 DN40 PN16 RF 3.21 (81)

11 3DN40 PN40 RF 3.21 (81)

11 6 DN40 PN100 RF 3.88 (99)

12.0-in. 150# RF 4.13 (105)

22 3 2.0-in. 300# RF 4.38 (111)

22 62.0-in. 600# RF 4.76 (121)

22 N 2.0-in. 900# RF 5.88 (149)

22 F2.0-in. 1500# RF 5.88 (149)

22 T 3.0-in. 2500# RF 9.87 (251)

12.0-in. 150# RTJ 4.32 (110)

22 3 2.0-in. 300# RTJ 4.63 (117)

22 62.0-in. 600# RTJ 4.82 (122)

22 N 2.0-in. 900# RTJ 5.94 (151)

22 F2.0-in. 1500# RTJ 5.94 (151)

22 T 3.0-in. 2500# RTJ 10.00 (254)

1DN50 PN16 RF 3.40 (86)

22 3 DN50 PN40 RF 3.52 (89)

22 6DN50 PN100 RF 4.31 (109

1 3.0-in. 150# RF 4.63 (117.5)

44 33.0-in. 300# RF 5.00 (126.9)

44 6 3.0-in. 600# RF 5.38 (136.6)

44 N4.0-in. 900# RF 8.19 (208.0)

44 F 4.0-in. 1500# RF 8.56 (217.5)

44 T4.0-in. 2500# RF 11.19 (284.2)

1 3.0-in. 150# RTJ 4.82 (122)

44 33.0-in. 300# RTJ 5.25 (133)

44 6 3.0-in. 600# RTJ 5.44 (138)

44 N4.0-in. 900# RTJ 8.25 (209)

44 F 4.0-in. 1500# RTJ 8.63 (219)

44 T4.0-in. 2500# RTJ 11.38 (289)

1 DN80 PN16 RF 3.85 (98)

44 3DN80 PN40 RF 4.16 (106)

44 6 DN80 PN100 RF 4.95 (126)

4585_QIG_AA.fm Page 10 Monday, January 19, 2009 11:18 AM

Andere Handbücher für Rosemount 585 Annubar

Inhaltsverzeichnis

Andere Emerson Messgerät Handbücher

Emerson

Emerson Rosemount SOLU COMP II Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount 0085 Bedienungsanleitung

Emerson

Emerson Daniel 3812 Programmierhandbuch

Emerson

Emerson World Class 3000 Bedienungsanleitung

Emerson

Emerson ROSEMOUNT 485 Annubar Pak-Lok Bedienungsanleitung

Emerson

Emerson 404B Bedienungsanleitung

Emerson

Emerson Rosemount 3051SAL Bedienungsanleitung

Emerson

Emerson Micro Motion 1700 Kurzanleitung

Emerson

Emerson Rosemount X-Stream Series Bedienungsanleitung

Emerson

Emerson Rosemount 5400 Series Bedienungsanleitung

Emerson

Emerson Rosemount 8782 Bedienungsanleitung

Emerson

Emerson Daniel PT Bedienungsanleitung

Emerson

Emerson Penberthy Handbuch

Emerson

Emerson Rosemount 9195 Bedienungsanleitung

Emerson

Emerson Daniel 3812 Bedienungsanleitung

Emerson

Emerson ControlWave Series Technisches Dokument

Emerson

Emerson Rosemount 8700 Series Konfigurationshandbuch

Emerson

Emerson Rosemount FCL Bedienungsanleitung

Emerson

Emerson Rosemount Analytical X-STREAM X2 Series Bedienungsanleitung

Emerson

Emerson CSI 2140 Bedienungsanleitung

Emerson

Emerson Micro Motion Viscomaster Bedienungsanleitung

Emerson

Emerson Rosemount 3812 Programmierhandbuch

Emerson

Emerson Daniel 3410 Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung