Emerson Rosemount 8700 Series Konfigurationshandbuch

www.rosemount.com

¢00809-0300-4727h¤

Manual Supplement

00809-0300-4727, Rev AA

June 2005 Rosemount 8700 Series

Step 1: Disassembling the Tube and Transmitter

Step 2: Preparing the Flowtube

Step 3: Preparing the Transmitter

Step 4: Wiring the Tube and Transmitter

Step 5: Perform a Loop Test

Start

End

Integral Mount to Remote Mount Conversion

0300-4727 Supplement.fm Page 1 Tuesday, June 7, 2005 9:27 AM

Manual Supplement

00809-0300-4727, Rev AA

June 2005

Rosemount 8700 Series

Introduction

This document will explain how to change an integrally mounted Rosemount 8732/8742

transmitter to a remote mount system.

Tools and Parts

• 10 mm Wrench to remove the bolts

• Phillips screwdriver

• Standard screwdriver

• 5 mm Allen Wrench

• Wrench appropriately sized for conduit fittings

• Rosemount spare part kit (08732-0016-0001)

IMPORTANT NOTICE

This installation guide provides basic guidelines. It does not provide instructions for

detailed configuration, diagnostics, maintenance, service, troubleshooting, or

installations. Refer to the Rosemount 8700 Series reference manual (document number

00809-0100-4727) for more instruction. The manual and this supplement are also

available electronically on www.rosemount.com.

WARNING

Explosions could result in death or serious injury:

Installation of this transmitter in an explosive environment must be in accordance with the

appropriate local, national, and international standards, codes, and practices. Please

review the Hazardous Locations Certifications for any restrictions associated with a safe

installation. In an Explosion-proof/Flame-proof installation, do not remove the transmitter

covers when power is applied to the unit.

Process leaks may cause harm or result in death

• Install and tighten thermowells or sensors before applying pressure.

• Do not remove the thermowell while in operation.

Electrical shock can result in death or serious injury

• Avoid contact with the leads and terminals. High voltage that may be present on leads

can cause electrical shock.

Emerson Process Management

Rosemount Inc.

8200 Market Boulevard

Chanhassen, MN USA 55317

T (US) (800) 999-9307

T (Intnl) (952) 906-8888

F (952) 949-7001

Emerson Process Management

Flow

Groeneveldselaan 6-8

3903 AZ Veenendaal

The Netherlands

Tel 31 (0) 318 549 549

Fax 31 (0) 318 549 559

Tel 0800-966 180 (U.K. only)

Fax 0800-966 181 (U.K. only)

Emerson Process Managemen

Asia Pacific Private Limited

1 Pandan Crescent

Singapore 128461

T (65) 6777 8211

F (65) 6777 0947 / (65) 6777 0743

Enquiries@AP.EmersonProcess.com

0300-4727 Supplement.fm Page 2 Tuesday, June 7, 2005 9:27 AM

Manual Supplement

00809-0300-4727, Rev AA

June 2005 Rosemount 8700 Series

STEP 1: DISASSEMBLING THE TUBE AND TRANSMITTER

1. Shut off the power going to the magnetic transmitter.

2. Remove the cover on the terminal strip side of the electronics housing.

3. Disconnect all wires from the terminal block. This will require a Phillips screwdriver.

4. Remove the conduit and wiring from the transmitter housing.

5. Replace the terminal strip side cover.

6. Open the LOI/Electronics cover.

7. Disconnect the quick connect connectors from the circuit board sockets. See Figure 4.

(For units equipped with a LOI, it will be necessary to remove the LOI to access the

connectors. This will require a small standard screwdriver.)

8. Remove the 4 bolts from the mounting plate on the flow tube holding the transmitter in

place. This will require the 10 mm wrench. See Figure 1.

9. Carefully lift the transmitter off of the mounting plate.

10.Disconnect the transmitter wiring from the terminal block on the flow tube. This will

require a small standard screwdriver. This wiring harness is no longer needed.

Figure 1.

Bolts

8732/8732_04a.eps

Bolts

0300-4727 Supplement.fm Page 3 Tuesday, June 7, 2005 9:27 AM

Manual Supplement

00809-0300-4727, Rev AA

June 2005

Rosemount 8700 Series

STEP 2: PREPARING THE FLOWTUBE

1. Remove the existing o-ring and discard appropriately.

2. Replace the o-ring with the new one supplied with the Remote Junction Box in the

conversion kit.

3. Place the remote mount junction box on the flowtube mounting plate.

4. Mount the junction box with the 4 bolts provided in the kit. See Figure 2.

Figure 2. Mount the junction box

Replacement O-Ring

8711/8711_01aa.eps

Mounting Plate

Junction Box

Bolts

0300-4727 Supplement.fm Page 4 Tuesday, June 7, 2005 9:27 AM

Manual Supplement

00809-0300-4727, Rev AA

June 2005 Rosemount 8700 Series

STEP 3: PREPARING THE TRANSMITTER

1. Position the remote mount terminal box adjacent to the transmitter and carefully feed the

wire leads so that they are accessible from the electronics access of the transmitter.

2. Place the O-Ring in the groove on the remote mount terminal box.

3. Mount the remote mount terminal box to the transmitter using the bolts provided.

See Figure 3.

4. Connect the wires from the remote mount terminal box to the electronics. Note that the

sockets are different sizes so that they can only be connected one way. See Figure 4.

5. Replace the LOI (if applicable).

6. Replace the electronics side cover.

Figure 3.

Remote mount

terminal box cover

8732/8732_03a.eps

Bolts

Remote mount

terminal box

O-rings

Wiring

Connection

0300-4727 Supplement.fm Page 5 Tuesday, June 7, 2005 9:27 AM

Manual Supplement

00809-0300-4727, Rev AA

June 2005

Rosemount 8700 Series

STEP 4: WIRING THE TUBE AND TRANSMITTER

1. Follow the procedures outlined in the magnetic flow meter manual for making the proper

wiring terminations between the Transmitter Remote Terminal box and the Flowtube

Terminal Junction Box.

2. Install all conduit and wiring in accordance with all local and plant electrical codes.

3. When the wiring between the flowtube and transmitter are complete, replace the covers

to both the flowtube junction box and the remote mount terminal box on the transmitter.

Figure 4.

Electrical Quick

Connect Connections

8732/8732_02a.eps

0300-4727 Supplement.fm Page 6 Tuesday, June 7, 2005 9:27 AM

Andere Handbücher für Rosemount 8700 Series

Inhaltsverzeichnis

Andere Emerson Messgerät Handbücher

Emerson

Emerson Rosemount 8732 Bedienungsanleitung

Emerson

Emerson Daniel 3814 Programmierhandbuch

Emerson

Emerson OPM 3000 Bedienungsanleitung

Emerson

Emerson Rosemount 5900 Bedienungsanleitung

Emerson

Emerson Rosemount WPG Bedienungsanleitung

Emerson

Emerson DIXELL XWEB1000D PRO Verdrahtungsschema

Emerson

Emerson Rosemount 1154DH Bedienungsanleitung

Emerson

Emerson Nelson CM-1 Bedienungsanleitung

Emerson

Emerson Rosemount 3410 Series Programmierhandbuch

Emerson

Emerson Rosemount 3051 CF Series Bedienungsanleitung

Emerson

Emerson Daniel 3812 Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Micro Motion 7829 Visconic Series Betriebshandbuch

Emerson

Emerson Klauke UAP432CFM Bedienungsanleitung

Emerson

Emerson Rosemount 8750W Bedienungsanleitung

Emerson

Emerson Rosemount 2051 Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount CT5100 Bedienungsanleitung

Emerson

Emerson ControlWave EFM 4710A Bedienungsanleitung

Emerson

Emerson ROSEMOUNT OCX8800C Bedienungsanleitung

Emerson

Emerson Rosemount 8800D Series Bedienungsanleitung

Emerson

Emerson FloBoss 103 Bedienungsanleitung

Emerson

Emerson Rosemount 6888C Bedienungsanleitung

Emerson

Emerson Rosemount CT5400 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung