Emerson Rosemount 8800D Series Bedienungsanleitung

Quick Start Guide

00825-0100-4004, Rev FE

October 2018

Rosemount™ 8800D Series Vortex

Flowmeter

1 About this guide

This guide provides basic guidelines for the Rosemount™ 8800D Series Vortex

Flowmeter. It does not provide instructions for detailed configuration,

diagnostics, maintenance, service, troubleshooting, Explosion-proof,

Flameproof, or Intrinsically Safe (I.S.) installations. Refer to the reference

manual for more instruction. The manuals and this quick start guide are also

available electronically on EmersonProcess.com/Rosemount.

WARNING

Explosions could result in death or serious injury.

Installation of this transmitter in an explosive environment must be in

accordance with the appropriate local, national, and international standards,

codes, and practices. Review the approvals section of thereference manual for

any restrictions associated with a safe installation.

•Before connecting a handheld communicator in an explosive atmosphere,

make sure the instruments in the loop are installed in accordance with

intrinsically safe or non-incendive field wiring practices.

•Verify the operating atmosphere of the flowmeter is consistent with the

appropriate product certifications.

•In an Explosion-proof/Flameproof installation, do not remove the

flowmeter covers when power is applied to the unit. Electrical shock can

result in death or serious injury.

WARNING

Electrical shock can result in death or serious injury.

•Avoid contact with the leads and terminals. High voltage that may be

present on leads can cause electrical shock.

1.1 Return policy

Emerson procedures must be followed when returning equipment. These

procedures ensure legal compliance with government transportation

agencies and help provide a safe working environment for Emerson

employees. Failure to follow Emerson procedures will result in your

equipment being refused delivery.

Quick Start Guide October 2018

2 Rosemount™ 8800D Series Vortex Flowmeter

1.2 Emerson Flow customer service

Email:

•Worldwide: [email protected]

•Asia-Pacific: [email protected]

Telephone:

North and South America Europe and Middle East Asia Pacific

United States 800 522 6277 U.K. 0870 240

1978

Australia 800 158 727

Canada +1 303 527

5200

The

Netherlands

+31 (0) 704

136 666

New Zealand 099 128 804

Mexico +41 (0) 41

7686 111

France 0800 917 901 India 800 440 1468

Argentina +54 11 4837

7000

Germany 0800 182

5347

Pakistan 888 550 2682

Brazil +55 15 3413

8000

Italy 8008 77334 China +86 21 2892

9000

Venezuela +58 26 1731

3446

Central &

Eastern

+41 (0) 41

7686 111

Japan +81 3 5769

6803

Russia/CIS +7 495 981

9811

South Korea +82 2 3438

4600

Egypt 0800 000

0015

Singapore +65 6 777

8211

Oman 800 70101 Thailand 001 800 441

6426

Qatar 431 0044 Malaysia 800 814 008

Kuwait 663 299 01

South Africa 800 991 390

Saudi Arabia 800 844 9564

UAE 800 0444

0684

October 2018 Quick Start Guide

Quick Start Guide 3

2 Installation

2.1 Mount the flowmeter

Design process piping so the meter body will remain full, with no entrapped

air. The vortex flowmeter can be installed in any orientation without affecting

accuracy. However, the following are guidelines for certain installations.

2.1.1 Vertical mounting

If the vortex flowmeter will be installed in a vertical orientation:

•Install upward or downward flow for gas or steam.

•Install upward flow for liquids.

Figure 2-1: Vertical installation

A. Gas flow

B. Liquid or gas flow

Quick Start Guide October 2018

4 Rosemount™ 8800D Series Vortex Flowmeter

2.1.2 Horizontal mounting

Figure 2-2: Horizontal installation

A. Preferred installation—meter body installed with electronics to side of pipe

B. Acceptable installation—meter body installed with electronics above pipe

For steam and fluids with small solids content, it is recommended to have the

flowmeter installed with the electronics to the side of the pipe. This will

minimize potential measurement errors by allowing the condensate or solids

to flow under the shedder bar without interrupting the vortex shedding.

2.1.3 High temperature mounting

The maximum temperature for integral electronics is dependent on the

ambient temperature where the flowmeter is installed. The electronics must

not exceed 185 °F (85 °C).

Figure 2-3 shows combinations of ambient and process temperatures needed

to maintain a housing temperature of less than 185 °F (85 °C).

October 2018 Quick Start Guide

Quick Start Guide 5

Figure 2-3: Ambient/Process temperature limits

200 (93)

180(82)

160 (71)

140 (60)

120 (49)

100 (38)

80 (27)

60 (16)

200 (93)

300 (149)

400 (204)

500 (260)

600 (316)

700 (371)

800 (427)

900 (482)

1000 (538)

100 (38)

A. Ambient temperature °F (°C)

B. Process temperature °F (°C)

C. 185 °F (85 °C) Housing temperature limit.

Note

The indicated limits are for horizontal pipe and vertical meter position, with

meter and pipe insulated with 3 in. (77 mm) of ceramic fiber insulation.

The following orientations are recommended for applications with high

process temperatures.

•Install with electronics head beside or below process pipe.

•Insulation around pipe may be necessary to maintain ambient

temperature below 185 °F (85 °C).

Note

Insulate pipe and meter body only. Do not insulate support tube bracket or

transmitter so heat can be dissipated.

2.1.4 Steam installations

Avoid installation shown in Figure 2-4. Such conditions may cause a water-

hammer condition at start-up due to trapped condensation.

Quick Start Guide October 2018

6 Rosemount™ 8800D Series Vortex Flowmeter

Figure 2-4: Improper installation

2.1.5 Upstream/downstream requirements

The flowmeter may be installed with a minimum of ten straight pipe

diameters (D) upstream and five straight pipe diameters (D) downstream by

following the K-factor corrections as described in the 8800 Installation Effects

Technical Data Sheet (00816-0100-3250). No K-factor correction is required if

35 straight pipe diameters upstream (35D) and 10 straight pipe diameters

downstream (10D) are present.

2.1.6 External pressure/temperature transmitters

When using pressure and temperature transmitters in conjunction with the

flowmeter for compensated mass flows, install the transmitters downstream

of the flowmeter as shown in Figure 2-5.

October 2018 Quick Start Guide

Quick Start Guide 7

Figure 2-5: Upstream/Downstream piping

A. Pressure transmitter

B. Four straight pipe diameters downstream

C. Temperature transmitter

D. Six straight pipe diameters downstream

2.1.7 Wafer style installation

Figure 2-6: Wafer style installation

A. Installation studs and nuts (supplied by customer)

B. Alignment ring

C. Gaskets (supplied by customer)

D. Flow direction

Quick Start Guide October 2018

8 Rosemount™ 8800D Series Vortex Flowmeter

2.1.8 Flanged style installation

Figure 2-7: Flanged style installation

A. Installation bolts and nuts (supplied by customer)

B. Gaskets (supplied by customer)

C. Flow direction

Note

The required bolt load for sealing the gasket joint is affected by several

factors, including operating pressure, gasket material, width, and condition. A

number of factors also affect the actual bolt load resulting from a measured

torque, including condition of bolt threads, friction between the nut head and

the flange, and parallelism of the flanges. Due to these application-dependent

factors, the required torque for each application may be different. Follow the

guidelines outlined in ASME PCC-1 for proper bolt tightening. Make sure the

flowmeter is centered between flanges of the same nominal size as the

flowmeter.

2.1.9 Insert integral temperature sensor (MTA option only)

About this task

Note

Step number of procedure corresponds with number in Figure 2-8.

October 2018 Quick Start Guide

Quick Start Guide 9

Figure 2-8: Thermocouple assembly

Procedure

1. Slide the thermocouple bolt (1) over the thermocouple (TC).

2. Place the 2-part ferrule (2) over the end tip of the thermocouple (TC).

3. Insert the thermocouple in to the thermowell hole (TW) on the

bottom side of the meter body.

Important

Carefully push the thermocouple in to the thermowell completely.

This is critical to get the proper insertion depth. Then thread the

thermocouple bolt in to the hole.

4. When the thermocouple bolt is hand tight, mark the position of the

bolt in relation to the meter body (the mark will help determine

rotations). Using a ½-in. wrench turn the bolt clockwise ¾ turn to seat

the ferrule.

Note

After completing Step 4, the ferrule and thermocouple bolt will be

permanently installed on the thermocouple.

5. Verify the rubber O-ring is installed on the electronics connection end

of the thermocouple.

6. Verify the 2.5 mm hex head screw is installed.

7. Insert the electronics end connector in to the transmitter housing.

Tighten the screw with a 2.5 mm hex bit to secure the connection.

Important

Do not over tighten hex screw.

Quick Start Guide October 2018

10 Rosemount™ 8800D Series Vortex Flowmeter

Andere Handbücher für Rosemount 8800D Series

Inhaltsverzeichnis

Andere Emerson Messgerät Handbücher

Emerson

Emerson Rosemount CT4400 Bedienungsanleitung

Emerson

Emerson Rosemount 370XA Bedienungsanleitung

Emerson

Emerson Hydrastep 2468 series Bedienungsanleitung

Emerson

Emerson Rosemount 8750W Bedienungsanleitung

Emerson

Emerson Rosemount CCO 5500 Bedienungsanleitung

Emerson

Emerson Rosemount 3812 Bedienungsanleitung

Emerson

Emerson Rosemount TCL Bedienungsanleitung

Emerson

Emerson Rosemount Analytical X-STREAM Enhanced... Anleitung zur Verwendung

Emerson

Emerson Energy Meter Bedienungsanleitung

Emerson

Emerson Rosemount 8800D Series Bedienungsanleitung

Emerson

Emerson MicroMotion HPC010 Bedienungsanleitung

Emerson

Emerson ALCO Controls AMI Series Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount CT5800 Bedienungsanleitung

Emerson

Emerson RLDS Betriebsanleitung

Emerson

Emerson Wireless Field Link Bedienungsanleitung

Emerson

Emerson Rosemount Bedienungsanleitung

Emerson

Emerson Micro Motion G-Series Bedienungsanleitung

Emerson

Emerson Appleton AEPGI Bedienungsanleitung

Emerson

Emerson Daniel 3410 Series Bedienungsanleitung

Emerson

Emerson Rosemount Analytical 400A Bedienungsanleitung

Emerson

Emerson Rosemount SOLU COMP II Bedienungsanleitung

Emerson

Emerson Rosemount 3051 CF Series Bedienungsanleitung

Emerson

Emerson Rosemount 5900S Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung