Emerson Rosemount 3051G Bedienungsanleitung

Quick Start Guide

00825-0100-4057, Rev EA

March 2020

Rosemount™ 3051G Pressure

Transmitter

with 4-20mA HART® Protocol (Revision 5

and 7)

Note

Before installing the transmitter, confirm the correct device driver is loaded on the host systems. See

System readiness.

NOTICE

This installation guide provides basic guidelines for Rosemount 3051 transmitters. It does not provide

instructions for configuration, diagnostics, maintenance, service, troubleshooting, Explosion-Proof,

Flameproof, or intrinsically safe (I.S.) installations. Refer to the Rosemount 3051 Reference Manual

(document number 00809-0100-5007) for more instruction. This manual is also available

electronically on www.emerson.com.

WARNING

Explosions could result in death or serious injury.

Installation of this transmitter in an explosive environment must be in accordance with the appropriate

local, national, and international standards, codes, and practices. Review the approvals section of the

Rosemount 3051 Reference Manual for any restrictions associated with a safe installation.

Before connecting a HART-based communicator in an explosive atmosphere, make sure the

instruments in the loop are installed in accordance with intrinsically safe or non-incendive field wiring

practices.

In an explosion-proof/flameproof installation, do not remove the transmitter covers when power is

applied to the unit.

Process leaks could result in death or serious injury.

To avoid process leaks, only use the o-ring designed to seal with the corresponding flange adapter.

Electrical shock could cause death or serious injury.

Avoid contact with the leads and terminals. High voltage that may be present on leads can cause

electrical shock.

Conduit/cable entries

Unless otherwise marked, the conduit/cable entries in the housing enclosure use a ½–14 NPT form.

Only use plugs, adapters, glands, or conduit with a compatible thread form when closing these entries.

Physical access

Unauthorized personnel may potentially cause significant damage to and/or misconfiguration of end

users’ equipment. This could be intentional or unintentional and needs to be protected against.

Physical security is an important part of any security program and fundamental to protecting your

system. Restrict physical access by unauthorized personnel to protect end users’ assets. This is true for

all systems used within the facility.

Contents

System readiness......................................................................................................................... 5

Transmitter installation................................................................................................................ 6

Safety instrumented systems installation................................................................................... 18

Product certifications................................................................................................................. 19

Quick Start Guide March 2020

2 Emerson.com/Rosemount

Declaration of Conformity..........................................................................................................28

China RoHS table........................................................................................................................32

March 2020 Quick Start Guide

Quick Start Guide 3

Quick Start Guide March 2020

4 Emerson.com/Rosemount

1 System readiness

1.1 Confirm HART revision capability

•If using HART based control or asset management systems, please

confirm the HART capability of those systems prior to transmitter

installation. Not all systems are capable of communicating with HART

Revision 7 protocol. This transmitter can be configured for either HART

Revision 5 or 7.

•For instructions on how to change the HART revision of your transmitter,

see Switch HART revision mode.

1.2 Confirm correct device driver

•Verify the latest device driver (DD/DTM™) is loaded on your systems to

ensure proper communications.

•Download the latest device driver at Emerson.com or FieldComm Group

1.2.1 Rosemount 3051 device revisions and drivers

Table 1-1 provides the information necessary to verify the correct device

driver and documentation for your device.

Table 1-1: Rosemount 3051 Device Revisions and Files

Identify device Find device driver Review

instructions

Review

functionality

Software

release

date

NAMUR

software

revision(

HART

software

revision(1)

HART

universal

revision

Device

revision

(2)

Manual

document

number

Changes to

software(3)

Dec-11 1.0.0 01 7 10 00809-0100

-4007

See (3) for list

of changes.

5 9

Jan-98 N/A 178 5 3 00809-0100

-4001

N/A

(1) NAMUR Software Revision is located on the hardware tag of the device. HART

Software Revision can be read using a HART capable configuration tool.

(2) Device driver file names use Device and DD Revision, e.g. 10_01. HART Protocol

is designed to enable legacy device driver revisions to continue to communicate

with new HART devices. To access new functionality, the new device driver must

be downloaded. It is recommended to download new device driver files to

ensure full functionality.

(3) HART Revision 5 and 7 Selectable, Safety Certified, Local Operator Interface,

Process Alerts, Scaled Variable, Configurable Alarms, Expanded Engineering

Units.

March 2020 Quick Start Guide

Quick Start Guide 5

2 Transmitter installation

2.1 Step 1: Mount the transmitter

2.1.1 Liquid applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Mount the transmitter so that the drain/vent valves are oriented

upward.

Figure 2-1: In-Line Liquid Applications

2.1.2 Gas applications

Procedure

1. Place taps in the top or side of the line.

2. Mount beside or above the taps.

Quick Start Guide March 2020

6 Emerson.com/Rosemount

Figure 2-2: In-Line Gas Applications

2.1.3 Steam applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Fill impulse lines with water.

Figure 2-3: In-Line Steam Applications

March 2020 Quick Start Guide

Quick Start Guide 7

Figure 2-4: Panel and Pipe Mounting

Rosemount 3051G

Panel mount(1) Pipe mount

(1) 1.5 / 16 × 1 ½ Panel bolts are customer supplied.

2.2 Inline gage transmitter orientation

The low side pressure port (atmospheric reference) on the inline gage

transmitter is located in the neck of the transmitter, behind the housing. The

vent path is 360° around the transmitter between the housing and sensor.

(See Figure 2-5).

Keep the vent path free of any obstruction, including but not limited to

paint, dust, and lubrication by mounting the transmitter so that the process

can drain away.

Figure 2-5: Inline Gage Low Side Pressure Port

ALow side pressure port (atmospheric reference)

Quick Start Guide March 2020

8 Emerson.com/Rosemount

2.3 Step 2: Set the switches

Set Alarm and Security switch configuration before installation as shown in

Figure 2-6.

•The Alarm switch sets the analog output alarm to high or low.

—Default alarm is high.

•The Security switch allows (unlocked symbol) or prevents (locked

symbol) any configuration of the transmitter.

—Default security is off (unlocked symbol).

Use the following procedure to change the switch configuration:

Procedure

1. If the transmitter is installed, secure the loop, and remove power.

2. Remove the housing cover opposite the field terminal side. Do not

remove the instrument cover in explosive atmospheres when the

circuit is live.

3. Slide the security and alarm switches into the preferred position

using a small screwdriver.

4. Reattach the transmitter cover. The cover must be fully engaged to

comply with explosion-proof requirements.

Figure 2-6: Transmitter Electronics Board

Without LCD display With LCD/LOI display

March 2020 Quick Start Guide

Quick Start Guide 9

Alarm

Security

2.4 Step 3: Connect the wiring and power up

Figure 2-7: Transmitter Wiring Diagrams (4–20 mA)

A24 Vdc supply

BRL ≥ 250

CCurrent meter (optional)

Shielded twisted pair cable should be used for best results. Use 24 AWG or

larger wire that does not exceed 5,000 feet (1500 meters) in length. If

applicable, install wiring with a drip loop. Arrange the drip loop so the

bottom is lower than the conduit connections and the transmitter housing.

CAUTION

Installation of the transient protection terminal block does not provide

transient protection unless the Rosemount 3051 case is properly grounded.

Do not run signal wiring in conduit or open trays with power wiring, or near

heavy electrical equipment.

Do not connect the powered signal wiring to the test terminals. Power could

damage the test diode in the terminal block.

Use the following steps to wire the transmitter:

Procedure

1. Remove the housing cover on the FIELD TERMINALS side.

2. Connect the positive lead to the “+” terminal (PWR/COMM) and the

negative lead to the “–” terminal.

3. Ground housing to fulfill local grounding regulations.

4. Ensure proper grounding. It is important that the instrument cable

shield be:

Quick Start Guide March 2020

10 Emerson.com/Rosemount

Andere Handbücher für Rosemount 3051G

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson Rosemount 1056 Bedienungsanleitung

Emerson

Emerson Rosemount 2090 Konfigurationshandbuch

Emerson

Emerson Rosemount 1408H Bedienungsanleitung

Emerson

Emerson Rosemount 1151 Bedienungsanleitung

Emerson

Emerson Rosemount 1208 Bedienungsanleitung

Emerson

Emerson Micro Motion Bedienungsanleitung

Emerson

Emerson Rosemount MultiVariable 3051SMV Bedienungsanleitung

Emerson

Emerson PT5N FLR Series Bedienungsanleitung

Emerson

Emerson Rosemount 702 Bedienungsanleitung

Emerson

Emerson Rosemount 8732EM Bedienungsanleitung

Emerson

Emerson Micro Motion 2400S Bedienungsanleitung

Emerson

Emerson wirelessHART Rosemount Series Bedienungsanleitung

Emerson

Emerson Rosemount 6888A Bedienungsanleitung

Emerson

Emerson Rosemount X-well 648 Bedienungsanleitung

Emerson

Emerson Micro Motion 4200 Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount 644R Bedienungsanleitung

Emerson

Emerson PT5N Series Bedienungsanleitung

Emerson

Emerson Rosemount 644 Bedienungsanleitung

Emerson

Emerson Rosemount 3095FC MultiVariable Bedienungsanleitung

Emerson

Emerson Rosemount 1056 Bedienungsanleitung

Emerson

Emerson Rosemount 3100 Series Bedienungsanleitung

Emerson

Emerson Rosemount 5081 Bedienungsanleitung

Emerson

Emerson Rosemount 1408A Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung