Emerson Rosemount 2051 Bedienungsanleitung

Quick Start Guide

00825-0200-4101, Rev FC

September 2016

with FOUNDATION™Fieldbus Protocol

Note

Before installing the transmitter, confirm the correct device driver is loaded on the host systems.

See “System readiness” on page 3.

Rosemount™ 2051 Pressure Transmitter

Rosemount 2051CF Series Flowmeter

00825-0200-4101_RevFC.fm Page 1 Monday, September 5, 2016 7:16 AM

September 2016

Quick Start Guide

NOTICE

This guide provides basic guidelines for Rosemount 2051 Transmitters. It does not provide instructions for

configuration, diagnostics, maintenance, service, troubleshooting, Explosion-Proof, Flame-Proof, or

intrinsically safe (I.S.) installations. Refer to the Rosemount 2051 Reference Manual for more instruction.

This manual is also available electronically on EmersonProcess.com/Rosemount.

Explosions could result in death or serious injury.

Installation of this transmitter in an explosive environment must be in accordance with the appropriate local,

national, and international standards, codes, and practices. Review the approvals section of the Rosemount

2051 Reference Manual for any restrictions associated with a safe installation.

In an Explosion-proof/Flameproof installation, do not remove the transmitter covers when power is

applied to the unit.

Process leaks may cause harm or result in death.

To avoid process leaks, only use the o-ring designed to seal with the corresponding flange adapter.

Electrical shock can result in death or serious injury.

Avoid contact with the leads and the terminals. High voltage that may be present on leads can cause

electrical shock.

Conduit/cable entries

Unless marked, the conduit/cable entries in the transmitter housing use a 1/2–14 NPT thread form. Entries

marked “M20” are M20 ⫻1.5 thread form. On devices with multiple conduit entries, all entries will have

the same thread form. Only use plugs, adapters, glands, or conduit with a compatible thread form when

closing these entries.

When installing in a hazardous location, use only appropriately listed or Ex certified plugs, adapters, or

glands in cable/conduit entries.

Contents

System readiness . . . . . . . . . . . . . . . . . . . . . . . . . 3

Mount the transmitter . . . . . . . . . . . . . . . . . . . . 4

Tagging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Housing rotation . . . . . . . . . . . . . . . . . . . . . . . . . 9

Set the switches . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Wire, ground, and power up . . . . . . . . . . . . . . 10

Configure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Zero trim the transmitter . . . . . . . . . . . . . . . . 19

Product Certifications . . . . . . . . . . . . . . . . . . . 20

00825-0200-4101_RevFC.fm Page 2 Monday, September 5, 2016 7:16 AM

Quick Start Guide

September 2016

1.0 System readiness

1.1 Confirm correct device driver

Verify the correct device driver (DD/DTM™) is loaded on your systems to

ensure proper communications.

Download the correct device driver at your host vendor download site,

EmersonProcess.com or Fieldbus.org.

Rosemount 2051 device revisions and drivers

Table 1 provides the information necessary to ensure you have the correct device

driver and documentation for your device.

Figure 1. Installation Flowchart

Table 1. Rosemount 2051 FOUNDATION Fieldbus Device Revisions and Files

Device

revision

(1)

1. FOUNDATION Fieldbus device revision can be read using a FOUNDATION Fieldbus capable configuration tool.

Host Device driver (DD)(2)

2. Device driver file names use device and DD revision. To access functionality, the correct device driver must be installed on your

control and asset management hosts, and on your configuration tools.

Obtain at Device driver (DTM) Manual document

number

All DD4: DD Rev 1 Fieldbus.org

EmersonProcess.com 00809-0200-4101,

Rev BA or newer

All DD5: DD Rev 1 Fieldbus.org

Emerson

AMS™Device Manager

V 10.5 or higher:

DD Rev 2

EmersonProcess.com

Emerson AMS Device Manager

V 8 to 10.5: DD Rev 1 EmersonProcess.com

Emerson 375/475: DD Rev 2 FieldCommunicator.com

All DD4: DD Rev 4 Fieldbus.org

EmersonProcess.com 00809-0200-4101,

Rev AA

All DD5: NA N/A

Emerson AMS Device Manager

V 8or higher: DD Rev 2 EmersonProcess.com

Emerson 375/475: DD Rev 2 FieldCommunicator.com

00825-0200-4101_RevFC.fm Page 3 Monday, September 5, 2016 7:16 AM

September 2016

Quick Start Guide

2.0 Mount the transmitter

2.1 Liquid applications Coplanar In-line

1. Place taps to the side of the

line.

2. Mount beside or below the

taps.

3. Mount the transmitter so the

drain/vent valves are oriented

upward.

2.2 Gas applications

1. Place taps in the top or side of

the line.

2. Mount beside or above the

taps.

2.3 Steam applications

1. Place taps to the side of the

line.

2. Mount beside or below the

taps.

3. Fill impulse lines with water.

00825-0200-4101_RevFC.fm Page 4 Monday, September 5, 2016 7:16 AM

Quick Start Guide

September 2016

Figure 2. Panel and Pipe Mounting

Panel mount(1)

1. 5/16 ⫻11/2panel bolts are customer supplied.

Pipe mount

Coplanar flange

Traditional flange

Rosemount 2051T

00825-0200-4101_RevFC.fm Page 5 Monday, September 5, 2016 7:16 AM

September 2016

Quick Start Guide

2.4 Bolting considerations

If the transmitter installation requires assembly of the process flanges, manifolds,

or flange adapters, follow the assembly guidelines to ensure a tight seal for

optimal performance characteristics of the transmitters. Use only bolts supplied

with the transmitter or sold by Emerson™as spare parts. Figure 3 on page 6

illustrates common transmitter assemblies with the bolt length required for

proper transmitter assembly.

Figure 3. Common Transmitter Assemblies

A. Transmitter with coplanar flange

B. Transmitter with coplanar flange and optional flange adapters

C. Transmitter with traditional flange and optional flange adapters

D. Transmitter with coplanar flange and optional manifold and flange adapters

Bolts are typically carbon steel or stainless steel. Confirm the material by viewing

the markings on the head of the bolt and referencing Table 2. If bolt material is

not shown in Table 2, contact a local Emerson Process Management

representative for more information.

Carbon steel bolts do not require lubrication and the stainless steel bolts are

coated with a lubricant to ease installation. However, no additional lubricant

should be applied when installing either type of bolt.

Use the following bolt installation procedure:

1. Finger tighten the bolts.

2. Torque the bolts to the initial torque value using a crossing pattern.

See Table 2 for initial torque value.

3. Torque the bolts to the final torque value using the same crossing pattern.

See Table 2 for final torque value.

4. Verify the flange bolts are protruding through the sensor module bolt holes

before applying pressure.

4 × 1.75-in.

(44 mm)

4 × 1.75-in.

(44 mm)

4 × 2.25-in.

(57 mm)

4 ×1.75-in.

(44 mm) 4 ×1.50-in.

(38 mm)

4 × 2.88-in.

(73 mm)

00825-0200-4101_RevFC.fm Page 6 Monday, September 5, 2016 7:16 AM

Quick Start Guide

September 2016

2.5 O-rings with flange adapters

2.6 Environmental seal for housing

Thread sealing (PTFE) tape or paste on male threads of conduit is required to

provide a water/dust tight conduit seal and meets requirements of NEMA®

Type 4X, IP66, and IP68. Consult factory if other Ingress Protection ratings are

required.

For M20 threads, install conduit plugs to full thread engagement or until

mechanical resistance is met.

2.7 In-line gage transmitter orientation

The low side pressure port (atmospheric reference) on the in-line gage

transmitter is located in the neck of the transmitter, behind the housing.

The vent path is 360° around the transmitter between the housing and sensor.

(See Figure 4.)

Table 2. Torque Values for the Flange and Flange Adapter Bolts

Bolt material Head markings Initial torque Final torque

Carbon Steel (CS) 300 in-lb 650 in-lb

Stainless Steel (SST) 150 in-lb 300 in-lb

Failure to install proper flange adapter O-rings may cause process leaks, which can result in death or

serious injury. The two flange adapters are distinguished by unique O-ring grooves. Only use the O-ring

that is designed for its specific flange adapter, as shown below:

O-ring location

A. Flange adapter

B. O-ring

C. PTFE based (profile is square)

D. Elastomer (profile is round)

Whenever the flanges or adapters are removed, visually inspect the O-rings. Replace them if there are

any signs of damage, such as nicks or cuts. If you replace the O-rings, re-torque the flange bolts and

alignment screws after installation to compensate for seating of the PTFE O-ring.

B7M

316

STM

316

B8M

Rosemount 3051S/3051/2051

00825-0200-4101_RevFC.fm Page 7 Monday, September 5, 2016 7:16 AM

September 2016

Quick Start Guide

Keep the vent path free of any obstruction, including but not limited to paint,

dust, and lubrication by mounting the transmitter so fluids can drain away.

Figure 4. In-line Gage Low Side Pressure Port

A. Pressure port location

3.0 Tagging

3.1 Commissioning (paper) tag

To identify which device is at a particular location use the removable tag provided

with the transmitter. Ensure the physical device tag (PD tag field) is properly

entered in both places on the removable commissioning tag and tear off the

bottom portion for each transmitter.

Note

The device description loaded in the host system must be at the same revision as this

device, see “System readiness” on page 3.

Figure 5. Commissioning Tag

A. Device revision

Commissioning Tag

DEVICE ID:

001151AC00010001440-12169809172

DEVICE REVISION: 2.1

PHYSICAL DEVICE TAG

DEVICE ID:

001151AC00010001440-12169809172

DEVICE REVISION: 2.1

S / N :

PHYSICAL DEVICE TAG

Device Barcode

Commissioning Tag

DEVICE ID:

0011512051010001440-12169809172

DEVICE REVISION: 1.1

PHYSICAL DEVICE TAG

DEVICE ID:

0011512051010001440 -12169809172

DEVICE REVISION: 1.1

S / N :

PHYSICAL DEVICE TAG

Device Barcode

00825-0200-4101_RevFC.fm Page 8 Monday, September 5, 2016 7:16 AM

Quick Start Guide

September 2016

Note

The device description loaded in the host system must be at the same revision as this

device. The device description can be downloaded from the host system website or

EmersonProcess.com/Rosemount by selecting Download Device Drivers under Product

Quick Links. You can also visit Fieldbus.org and select End User Resources.

4.0 Housing rotation

To improve field access to wiring or to better view the optional LCD display:

Figure 6. Housing Rotation

A. Housing rotation set screw (5/64-in.)

1. Loosen the housing rotation set screw.

2. First rotate the housing clockwise to the desired location.

3. If the desired location cannot be achieved due to thread limit, rotate the

housing counter clockwise to the desired location (up to 360° from thread

limit).

4. Re-tighten the housing rotation set screw to no more than 7 in-lb when

desired location is reached.

5.0 Set the switches

Set simulate and security switch configuration before installation as shown in

Figure 7.

The simulate switch enables or disables simulated alerts and simulated AI

Block status and values. The default simulate switch position is enabled.

The security switch allows (unlocked symbol) or prevents (locked symbol) any

configuration of the transmitter.

- Default security is off (unlocked symbol).

- The security switch can be enabled or disabled in software.

Use the following procedure to change the switch configuration:

1. If the transmitter is installed, secure the loop, and remove power.

2. Remove the housing cover opposite the field terminal side. Do not remove the

instrument cover in explosive atmospheres when the circuit is live.

3. Slide the security and simulate switches into the preferred position.

4. Replace the housing cover.

00825-0200-4101_RevFC.fm Page 9 Monday, September 5, 2016 7:16 AM

September 2016

Quick Start Guide

Note

It is recommended the cover be tightened until there is no gap between the cover and

housing.

Figure 7. Simulate and Security Switches

6.0 Wire, ground, and power up

Use of copper wire of sufficient size to ensure that the voltage across the

transmitter power terminals does not drop below 9 Vdc. Power supply voltage

can be variable, especially under abnormal conditions such as when operating on

battery backup. A minimum of 12 Vdc under normal operating conditions is

recommended. Shielded twisted pair Type A cable is recommended.

1. To power the transmitter, connect the power leads to the terminals indicated

on the terminal block label.

Figure 8. Wiring Terminals

A. Simulate disabled position

B. Simulate switch

C. Simulate enabled position (default)

D. Security locked position

E. Security switch

F. Security unlocked position (default)

A. Minimize distance

B. Trim shield and insulate

C. Protective grounding terminal

(do not ground cable shield at the transmitter)

D. Insulate shield

E. Minimize distance

F. Connect shield back to the power

supply ground

00825-0200-4101_RevFC.fm Page 10 Monday, September 5, 2016 7:16 AM

Andere Handbücher für Rosemount 2051

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson Rosemount 3051 CF Series Bedienungsanleitung

Emerson

Emerson Rosemount 56 Bedienungsanleitung

Emerson

Emerson Rosemount 4600 Bedienungsanleitung

Emerson

Emerson Rosemount 3051HT Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount Oxymitter 4000 Bedienungsanleitung

Emerson

Emerson MICRO MOTION 1500 Kurzanleitung

Emerson

Emerson Micro Motion 5700 Bedienungsanleitung

Emerson

Emerson Rosemount 705 Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount 3051SF Series Bedienungsanleitung

Emerson

Emerson Rosemount 2051 Bedienungsanleitung

Emerson

Emerson Rosemount 2051 Wireless Series Bedienungsanleitung

Emerson

Emerson Rosemount 2051 Bedienungsanleitung

Emerson

Emerson Rosemount 8782 Bedienungsanleitung

Emerson

Emerson Rosemount 2051G Bedienungsanleitung

Emerson

Emerson CSI 9420 Bedienungsanleitung

Emerson

Emerson Rosemount 3051P Bedienungsanleitung

Emerson

Emerson Rosemount 5408 Bedienungsanleitung

Emerson

Emerson Incus GDU-01-TT Bedienungsanleitung

Emerson

Emerson Rosemount 4088B MultiVariable Bedienungsanleitung

Emerson

Emerson Rosemount 5408 Bedienungsanleitung

Emerson

Emerson Rosemount 550PT Bedienungsanleitung

Emerson

Emerson Magtech LTM-350 Series Handbuch

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung