Emerson Rosemount 3051S Series Bedienungsanleitung

Quick Start Guide

00825-0100-4803, Rev EG

October 2018

Rosemount™ 3051S and 3051SF Series

Flow Meter MultiVariable™ Transmitters

Safety messages

NOTICE

This guide provides basic guidelines for Rosemount™ 3051S MultiVariable™ Transmitter (3051SMV). It

also provides the basic Rosemount 3051SMV configuration guidelines for the Rosemount 3051SFA,

Rosemount 3051SFC, and Rosemount 3051SFP. It does not provide instructions for diagnostics,

maintenance, service, or troubleshooting. Refer to the Rosemount 3051SMV Reference Manual for

more instruction.This document is also available electronically on Emerson.com/Rosemount.

WARNING

Explosions could result in death or serious injury.

Installation of device in an explosive environment must be in accordance with appropriate local,

national, and international standards, codes, and practices.

Review Rosemount 3051SMV Reference Manual for any restrictions associated with a safe installation.

•Before connecting a handheld communicator in an explosive atmosphere, make sure the

instruments in the loop are installed in accordance with intrinsically safe or non-incendive field

wiring practices.

•In an explosion-proof/flameproof installation, do not remove the transmitter covers when power

is applied to the unit.

Process leaks could result in death or serious injury.

•Install and tighten process connectors before applying pressure.

Electrical shock could cause death or serious injury.

•Avoid contact with the leads and terminals. High voltage that may be present on leads can cause

electrical shock.

Conduit/cable entries

•Unless marked, the conduit/cable entries in the transmitter housing use a ½–14 NPT thread form.

Entries marked “M20” are M20 × 1.5 thread form. On devices with multiple conduit entries, all

entries will have the same thread form. Only use plugs, adapters, glands, or conduit with a

compatible thread form when closing these entries.

•When installing in a hazardous location, use only appropriately listed or Ex certified plugs, glands,

or adapters in cable/conduit entries.

Contents

Mount the transmitter .................................. 3

Consider housing rotation ............................ 9

Set the switches ......................................... 10

Connect wiring and power up ..................... 11

Engineering Assistant installation ............... 15

Flow configuration ..................................... 17

Verifying device configuration .................... 26

Trimming the transmitter ........................... 30

Safety instrumented systems installation ... 31

Product certifications ................................. 32

Quick Start Guide October 2018

2 Rosemount 3051SMV

1 Mount the transmitter

1.1 Liquid flow applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Mount the transmitter so that the drain/vent valves are oriented

upward.

A. Direction of flow

1.2 Gas flow applications

Procedure

1. Place taps in the top or side of the line.

2. Mount beside or above the taps.

A. Direction of flow

October 2018 Quick Start Guide

Quick Start Guide 3

1.3 Steam flow applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Fill impulse lines with water.

A. Direction of flow

1.4 Mounting brackets

Figure 1-1: Mounting Bracket – Coplanar Flange

Panel mount Pipe mount

Quick Start Guide October 2018

4 Rosemount 3051SMV

Figure 1-2: Mounting Brackets – Traditional Flange

Panel mount Pipe mount

Figure 1-3: Mounting Brackets – In-line

Panel mount Pipe mount

1.5 Bolting considerations

About this task

If the transmitter installation requires assembly of a process flange, manifold,

or flange adapters, follow these assembly guidelines to ensure a tight seal for

optimal performance characteristics of the transmitter. Only use bolts

supplied with the transmitter or sold by Emerson™ as spare parts. Figure 1-4

illustrates common transmitter assemblies with the bolt length required for

proper transmitter assembly.

October 2018 Quick Start Guide

Quick Start Guide 5

Figure 1-4: Common Transmitter Assemblies

4 × 1.75-in.

(44 mm)

4 × 1.75-in.

(44 mm)

4 × 2.25-in.

(57 mm)

4 ×1.75-in.

(44 mm) 4 ×1.50-in.

(38 mm)

4 × 2.88-in.

(73 mm)

A. Transmitter with coplanar flange

B. Transmitter with coplanar flange and optional flange adapters

C. Transmitter with traditional flange and optional flange adapters

D. Transmitter with coplanar flange and optional Rosemount Conventional

Manifold and flange adapters

Note

For all other manifolds, contact Customer Central technical support.

Bolts are typically carbon steel or stainless steel. Confirm the material by

viewing the markings on the head of the bolt and referencing Table 1-1 . If

bolt material is not shown in Table 1-1, contact the local Emerson

representative for more information.

Use the following bolt installation procedure:

Procedure

1. Carbon steel bolts do not require lubrication and the stainless steel

bolts are coated with a lubricant to ease installation. However, no

additional lubricant should be applied when installing either type of

bolt.

2. Finger-tighten the bolts.

3. Torque the bolts to the initial torque value using a crossing pattern.

See Table 1-1 for initial torque value.

4. Torque the bolts to the final torque value using the same crossing

pattern. See Table 1-1 for final torque value.

Quick Start Guide October 2018

6 Rosemount 3051SMV

5. Verify the flange bolts are protruding through the sensor module

before applying pressure (see Figure 1-5).

Example

Table 1-1: Torque Values for the Flange and Flange Adapter Bolts

Bolt material Head markings Initial torque Final torque

Carbon Steel

(CS)

B7M

300 in-lb 650 in-lb

Stainless Steel

(SST)

316

STM

316

B8M

150 in-lb 300 in-lb

Figure 1-5: Proper Bolt Installation

A. Bolt

B. Sensor module

October 2018 Quick Start Guide

Quick Start Guide 7

1.6 O-rings with flange adapters

WARNING

Failure to install proper flange adapter O-rings may cause process leaks, which

can result in death or serious injury. Only use the O-ring that is designed for its

specific flange adapter.

A. Flange adapter

B. O-ring

C. PTFE-based profile (square)

D. Elastomer profile (round)

Whenever the flange or adapters are removed, visually inspect the O-rings.

Replace them if there are any signs of damage, such as nicks or cuts. If the O-

rings are replaced, re-torque the flange bolts and alignment screws after

installation to compensate for seating of the O-rings.

Quick Start Guide October 2018

8 Rosemount 3051SMV

2 Consider housing rotation

About this task

To improve field access to wiring or to better view the optional LCD display:

Procedure

1. Loosen the housing rotation set screw.

2. Turn the housing up to 180° left or right of its original (as shipped)

position.

3. Re-tighten the housing rotation set screw.

Figure 2-1: Transmitter Housing Set Screw

A. LCD display

B. Housing rotation set screw (3/32-in.)

CAUTION

Do not rotate the housing more than 180° without first performing a

disassembly procedure (refer to Troubleshooting for more

information). Over-rotation may sever the electrical connection

between the sensor module and the electronics.

October 2018 Quick Start Guide

Quick Start Guide 9

3 Set the switches

The transmitter’s default configuration sets the alarm condition to high (HI)

and the security to off.

Procedure

1. If the transmitter is installed, secure the bus and remove power.

2. Required: Remove the transmitter cover opposite the field terminal

side. Do not remove the instrument covers in explosive environments

when the circuit is live.

3. Slide the Security and Alarm switches into the preferred position by

using a small screwdriver.

Note

The Security switch will need to be in the off position in order to make

any configuration changes.

4. Required: In order to meet explosion-proof requirements, reinstall the

housing cover and tighten so the cover is fully seated with metal to

metal contact between the housing and cover. After the cover is

seated properly, replace the flathead screw located on the bottom of

the housing cover.

Figure 3-1: Transmitter Switch Configuration

A B

A. Security

B. AC Termination

Quick Start Guide October 2018

10 Rosemount 3051SMV

Andere Handbücher für Rosemount 3051S Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson Rosemount 644 Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Bedienungsanleitung

Emerson

Emerson Rosemount 5408 Bedienungsanleitung

Emerson

Emerson Rosemount 148 Bedienungsanleitung

Emerson

Emerson Rosemount Ultrasonic 3107 Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Bedienungsanleitung

Emerson

Emerson Rosemount 2090 Konfigurationshandbuch

Emerson

Emerson Rosemount 648 Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Bedienungsanleitung

Emerson

Emerson Rosemount 848T Bedienungsanleitung

Emerson

Emerson Net Safety Millennium II Bedienungsanleitung

Emerson

Emerson 6081-P Bedienungsanleitung

Emerson

Emerson Rosemount 148 Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Series Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Konfigurationshandbuch

Emerson

Emerson Rosemount 8732EM Bedienungsanleitung

Emerson

Emerson Rosemount 3051P Bedienungsanleitung

Emerson

Emerson Rosemount OCX 8800 Bedienungsanleitung

Emerson

Emerson Rosemount 2051G Bedienungsanleitung

Emerson

Emerson Rosemount 1056 Bedienungsanleitung

Emerson

Emerson Rosemount Wireless Permasense WT210 Bedienungsanleitung

Emerson

Emerson Rosemount MultiVariable 3051SMV Bedienungsanleitung

Emerson

Emerson Rosemount 3051HT Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung